V I V O MOUNT-KB05HT Clamp on Height Adjustable Tilting Keyboard Tray Instruction Manual

: May 15, 2024
: V I V O

Table of Contents

MOUNT-KB05HT Clamp on Height Adjustable Tilting Keyboard Tray
Package Contents
Included Hardware & Tools
ASSEMBLY STEPS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Clamp-on Tilting Keyboard Tray with
Height Adjustment

V I V O MOUNT-KB05HT Clamp on Height Adjustable Tilting Keyboard
Tray

SKU: MOUNT-KB05HT
Instruction Manual

MOUNT-KB05HT Clamp on Height Adjustable Tilting Keyboard Tray

Assembly Video & Product Info
www.vivo-us.com/products/mount-kb05ht

CAUTION!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please contact our product support team at 309-278-5303 or help@vivo- us.com for further assistance. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.

WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

DO NOT EXCEED WEIGHT CAPACITY
FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY.

We’re Here for You
Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.

Give us a Call:
309-278-5303| AVG. RESOLUTION TIME (within office hrs): 5M 4S
---|---
Chat Us:
www.vivo-us.com| AVG. RESOLUTION TIME (within office hrs): < 15 M
Email Us:
help@vivo-us.com| AVG. RESPONSE TIME (within office hrs): 1HR 8M
– 23% within < 15m
– 38% within < 30m
– 61% within < 1hr
– 83% within < 2hr
– 92% within < 3hr

Package Contents

V I V O MOUNT-KB05HT Clamp on Height Adjustable Tilting Keyboard Tray -
Package Contents

Included Hardware & Tools

V I V O MOUNT-KB05HT Clamp on Height Adjustable Tilting Keyboard Tray -
Included Hardware

Tools Needed:	Weight Capacity:

ASSEMBLY STEPS

STEP 1
Flip Keyboard Tray (A) upside down and install Keyboard Stop (B) into predrilled holes using M5x12mm Flat Head Screws (S-D) and a Phillips screwdriver.

V I V O MOUNT-KB05HT Clamp on Height Adjustable Tilting Keyboard Tray -
ASSEMBLY STEPS

STEP 2
Secure Tilting Bracket Set (E) to the outer edges of Keyboard Tray (A) using M5x12mm Round Head Screws (S-B) and a Phillips screwdriver.

V I V O MOUNT-KB05HT Clamp on Height Adjustable Tilting Keyboard Tray -
Secure Tilting Bracket

Note: The brackets should protrude past the keyboard tray on the side of Keyboard Stop (B).

STEP 3
Assemble Support Brackets (C) onto the Tilting Bracket Set (E) slider rails using M4x7mm Screws (S-A) and a Phillips screwdriver. Ensure the countersunk holes on Support Brackets (C) are facing outward, as shown below.

V I V O MOUNT-KB05HT Clamp on Height Adjustable Tilting Keyboard Tray -
ASSEMBLY STEPS 2

STEP 4
Assemble Clamp Set (D) to Support Brackets (C) at desired height using M5x9mm Flat Head ScrewScrews (S-C). Tighten with a Phillips screwdriver.

V I V O MOUNT-KB05HT Clamp on Height Adjustable Tilting Keyboard Tray -
ASSEMBLY STEPS 3

Adjusting Clamp for Greater Desktop Thickness
Clamps are pre-assembled for compatibility with desktops 0-65mm (2.56”) thick. The clamp features two additional height settings if the pre-assembled clamp does not work with your desktop.
Remove the preinstalled screws using 4mm Allen Wrench (T-A) and adjusting the position of the upper clamp according to your desktop thickness.

0-45mm (1.77”)
Desktop Thickness:
Use upper hole set.
5-85mm (0.197” – 3.35”)
Desktop Thickness:
Use lower hole set.

STEP 5
Place the assembled keyboard mount on the edge of the desk, then slide Clamp Pads (G) on the underside of each Clamp (D). Tighten clamps fully to secure to desktop. Remove the protective film on Wrist Pad (F) and place in desired location on Keyboard Tray (A).

Note: To ensure the keyboard tray is leveled correctly, do not over- tighten clamps.

V I V O MOUNT-KB05HT Clamp on Height Adjustable Tilting Keyboard Tray -
ASSEMBLY STEPS 5

STEP 6
Clamps are able to rotate and clamp onto a corner section of an L-desk. To adjust the tilt angle of the tray, remove the thumbscrews on both tilting brackets. Adjust the angle of the tray to your desired position, then reinstall the thumbscrews into the new adjustment locations to secure.

V I V O MOUNT-KB05HT Clamp on Height Adjustable Tilting Keyboard Tray -
ASSEMBLY STEPS 6