Zoroufy 2023 Adjustable Legacy Wall Hanger Collection Installation Guide

June 13, 2024
Zoroufy

Zoroufy 2023 Adjustable Legacy Wall Hanger Collection

Zoroufy-2023-Adjustable-Legacy-Wall-Hanger-Collection-
PRO

Product Information

  • Product Name: Finial
  • Design: Pineapple
  • Collection Specifications: Wall Hanger
  • Rod Gauge: 3
  • Rod Diameter: .031 inches
  • Length: 3.25 inches

Product Usage Instructions

  1. Attach the first finial:
    • Insert the rod into the finial base.
    • Tighten the small screw to secure the finial in place.
  2. Extend the rod to the desired length:
    • Remove the plastic cap to extend the rod.
  3. Slide the end bracket onto the rod.
  4. Hold the extended rod in the desired position against the wall and mark the position of the holes in the attached end bracket.
  5. Install the attached end bracket while supporting the opposite side.
  6. Slide the end bracket onto the opposite end of the extended rod and level the rod to locate the desired position.
  7. Install the end bracket.
  8. Attach the remaining finial:
    • Insert the rod into the finial base.
    • Tighten the small screw to secure the finial in place.
  9. Locate the desired position for both the center support brackets.
  10. Attach the clips to the rug, tapestry, or quilt and secure in place by tightening the disc.
  11. Place the clips over the rod. (Use the provided clips based on rod size – / and 5/8 clips)
  12. If bracket screws are not installed into a stud, use wall anchors.
  13. To clean, simply wipe with a soft dry cloth.
  14. Periodically check and tighten all screws and hardware.

Note: All parts are lacquer coated to resist tarnishing. Do not use brass cleaner or other abrasives.

SPECIFICATIONS

Zoroufy-2023-Adjustable-Legacy-Wall-Hanger-
Collection-1

  • Pineapple: 3 1/4”
  • ROD GAUGE: 031”
  • ROD DIAMETER: 1/2” into 5/8”

Zoroufy® Legacy rods slide into each finial approximately 3/4”. Finials attach to the rod.

INSTALLATION INSTRUCTIONS

Zoroufy-2023-Adjustable-Legacy-Wall-Hanger-
Collection-2

  1. Attach the first finial by inserting the 5/8” rod into the 5/8“ finial base and tightening the small scew.
  2. Extend the rod to the desired length (remove plastic cap to extend rod.)
  3. Slide the 5/8” end bracket onto the 5/8“ rod. Hold the extended rod in the desired position against wall and mark the position of the holes in the attached 5/8” end bracket.
  4. While supporting the opposite side, install the attached 5/8“ end bracket.
  5. Slide the 1/2” end bracket onto the opposite 1/2” end of the extended rod and locate the desired position by leveling the rod. Install the 1/2” end bracket.
  6. After both end brackets are installed, attach the remaining finial by inserting 1/2” rod into 1/2” finial base and tightening the small screw.
  7. Located the desired position for both the 5/8” and the 1/2” center support brackets.
  8. Attach the clips to the rug, tapestry, or quilt and secure in place by tightening the disc. Place the clips over the rod. (Both 1/2” and 5/8” clips are provided and should be used on corresponding rods.)

Wall anchors must be used if bracket screws are not installed into a stud.

ALL PARTS ARE LACQUER COATED TO RESIST TARNISHING. DO NOT USE BRASS CLEANER OR OTHER ABRASIVES. TO CLEAN, SIMPLY WIPE WITH A SOFT DRY CLOTH. PERIODICALLY CHECK AND TIGHTEN ALL SCREWS AND HARDWARE.

2140 W. GREENVIEW DR. SUITE 5, MIDDLETON, WI 53562-0345 • 800-762-1525info@zoroufy.comwww.zoroufy.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals