Solar Lighting DiRECt SLDMP008-610-PIR Residential Multi-Purpose Light Instruction Manual

June 3, 2024
Solar Lighting DIRECT

Solar Lighting DiRECt SLDMP008-610-PIR Residential Multi-Purpose Light

Solar-Lighting-DiRECt-SLDMP008-610-PIR-Residential-Multi-Purpose-Light-
PRODUCT

PACKAGE CONTENTS

  • 1 x Light Fitting
  • 1 x Solar Panel
  • 1 x Wall Mount & Bracket 1 x Pack of Screws
  • 1 x Remote

FEATURES

  1. Remote controlled sensor modes
  2. Sensor Triggered Piezoelectric alarm
  3. 6-8 hours Operation per day
  4. Pyro-electric Infrared Sensor

INSTALLATION METHOD

  1. Remove contents from packaging
  2. Refer to FIGURE 1 below for the location of your concealed on/off power button. To activate the light use the supplied pin and press & hold for 2 seconds to turn “ON/OFF”Solar-Lighting-DiRECt-SLDMP008-610-PIR-Residential-Multi-Purpose-Light-FIG-2

ASSEMBLY & INSTALLATION

Light Fitting – With the supplied screws, fix the wall mount to the wall. Connect light fitting to the bracket & connect to the wall mount by sliding into the back of the bracket
Solar Panel – Using the supplied screws, fasten your solar panel to the wall (Note; make sure the length from the light fitting is within 3m so the cable can reach). Place in a location that receives maximum direct sunlight throughout the day

IMPORTANT NOTES

  • Please ensure you place your solar panel in a location where it can achieve a minimum of 6HRS DIRECT SUNLIGHT
  • Be aware that on overcast/cloudy days, the solar panel will still charge. However, not a s efficiently as a sunny day, so the battery may not reach full cap acity. Therefore, your light may turn off earlier than specified
  • It’s best not to install the fitting under a street light, porch light or similar as this may stop the automatic day-night sensor triggering and result in your lights not turning on

TROUBLESHOOTING

Phenomenon Cause Inspection Method Solution
  Switch  
  hasn’t been

turned

| Determine what position the switch is

in

| Turn the switch on
Light won’t| on|  |
turn on|  | Period of rainy or| Charge the light
 | Battery| cloudy weather or| in direct
 | has run| installation site| sunlight for 1-2
 | flat| doesn’t provide| days then check
 |  | enough direct sunlight| again
 |  |  | 1. Charge the
 |  | 1. Bad installation site| battery in direct
 |  | for the solar panel| sunlight for 1-2
 | Low| 2. Dust or leaves are| days with the
The light only| Battery| covering the panel| switch off, then
stays on for a|  | 3. Long period of| check again
short amount|  | overcast weather| 2. Clean the
of time|  |  | solar panel
 |  | 1. Access the light and| Contact SLD
 | Battery| & replace battery| Customer
 | Failure| 2. Battery has| Service to buy
 |  | matured| new batteries

UNDERSTANDING YOUR REMOTE

Solar-Lighting-DiRECt-SLDMP008-610-PIR-
Residential-Multi-Purpose-Light-FIG-3

  • Press once to switch light “ON”
    Once the alarm has beeped once, this is now in Sensor mode. A dull light will be emitted when no movement is detected. Once the sensor is triggered the light turns to 100% brightness for approximately 20 seconds

  • Press once to switch light completely “OFF”

  • Press twice to switch the alarm feature “ON”
    Alarm will beep twice & take approximately 20 seconds to set, once set you will
    hear a long beep to confirm. Light will operate as per the previous option, however once the sensor is triggered both the brighter lights & alarm will operate together for approximately 20 seconds

  • Press once to switch the alarm feature “OFF”

Customer Service Numbe r : 1300 135 911
www.solarlightingdirect.com.au

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Solar Lighting DIRECT User Manuals

Related Manuals