tala Walnut Nine Pendant with Sphere IV User Guide

tala Walnut Nine Pendant with Sphere IV

• Thoughtful lighting, responsibly designed in London.
• Thank you for making the switch to Tala.
• Discover the full Tala family at us.tala.co.uk

BEFORE STARTING

We recommend the installation of our Canopy and Pendants is performed by a qualified electrician. Please read the instructions thoroughly before commencing work and keep them for future reference. Please take extreme care when carrying out these instructions.
IMPORTANT
This light fitting must be connected to the earth supply. If your lighting circuit does not have an earth, ask a qualified electrician to provide an earth facility. This light fitting is suitable for indoor use only. This fitting operates on 120V mains voltage. For a list of recommended dimmers to pair with this light fitting, please visit our website.
WARNING

• You must switch off electricity supply at the mains during installation and maintenance. We strongly recommend that you withdraw the fuse or switch off the circuit breaker whilst work is in progress.
• Do not only turn off the wall switch. All fittings must be installed in accordance with current NFPA 70, National Electrical Code (NEC).

RECOMMENDED EQUIPMENT

• Small flat head screwdriver
• Wire strippers
• Insulation tape
  Further equipment may be required for fixing to your ceiling.

NINE PENDANT – PROVIDED COMPONENTS

• A. x1 Ceiling Bracket
• B. x1 Ceiling Plate
• C. x9 Cord Grips
• D. x3 Safety Teathers and Clips
• E. x1 Junction Box
• F. x9 Tala Pendants Oak, Walnut, Brass or Graphite
• G. x1 M4 20MM bolt

INSTALLATION INSTRUCTION

• STEP 1
  Attach A to the ceiling using screws and plug. Make sure to use screws and plugs that are appropriate for the ceiling type

• STEP 2A – REVERSE OR REPLACE DISPLAY PANEL (OPTIONAL)

  • Remove panel B and display disk 3 by loosening all nuts 2 and washers 1 Including the nine cord grips C
  • To display the alternative finish, rotate disc 3 180 degrees. Note, not all display panels have an alternative finish.

• STEP 2B

  • Re-assemble the plate in the same order and fasten it securely with nuts 1 and washers 2
  • Replace the Cord grips C and secure with the nuts and washers.
  • Tighten all firmly with a spanner/wrench

• STEP 3
  Attach ceiling plate B to ceiling bracket A using safety tether clips D

• STEP 4
  Thread all nine pendant cables F though ceiling plate cord grips C

• STEP 5

  • Pull cables through to your desired length. See end of this guide for our recommended lengths and distance between bulbs.
  • Using a flat head screwdriver, tighten set screws C to secure them.

• STEP 6
  Cut off excess cable and strip wires to expose the copper core. Maintain all double insulation.

• STEP 7
  Connect the pendants, plate and mains wiring as shown.

• STEP 8
  • Lift B to sit flush with A.
  • Make sure the pins 1 are located at the opening of the bayonet fitting 2

• STEP 9
  • Rotate plate B anti-clockwise until the pin is locked into the 1 bayonette mechanism 2.
  • Secure plate B in place using bolt G

• STEP 10
  Insert bulbs into pendants F and screw clockwise

PENDANTS DISPLAY GUIDE

MINIMUM CORD LENGTH
For all bulbs shortest recomended cord length is 14 in

DISTANCE BETWEEN PENDANTS
Recomended minimum distance between pendant, dependant on bulb style, are as follows:

• Voronoi I – 6 in
• Voronoi II – 8 in
• Voronoi III – 14 in
• Basalt – 4 in
• All other bulbs – 4 in

PENDANTS – RECOMMENDED CABLE LENGTHS

• SCENARIO 1
  Above a coffee or dining table, or where height is required for seated tasks

• SCENARIO 2
  Above side tables, or where height is required for storage

• SCENARIO 3
  Above a kitchen island or bar, or where height is required for standing tasks

• SCENARIO 4
  Above a stairwell or walkway, or where height is required for walking underneath

CARE AND CLEANING

We recommend cleaning with a soft dry cloth. Do not use abrasive materials as these will damage the finish of the product.

WARRANTY AND AFTER-CARE

• This product has a three-year warranty. Within this time  we will replace any parts that have functional defects.
• Please report any faults by emailing: customerservice@tala.co.uk

Join the Community

• Instagram: @tala
• Facebook: talaHQ
• Pinterest: TalaLED
• Tag: lighttoliveby
• Tala Studios, 25B Vyner Street, London E2 9DG
• +44 20 3026 3246
• hello@tala.co.uk

References

• Tala | Shop Official Tala® Lighting | Light to Live By – Tala US

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>