ABESTORM SN35P 70 Pints Crawl Space Dehumidifiers Instruction Manual

ABESTORM SN35P 70 Pints Crawl Space Dehumidifiers

Product Information

• Specifications
  • Model: XDUGLDQ613
  • Power: 6 volts
  • Weight: 1 pound
  • Dimensions: 6 x 3 x 1 inches

Product Usage Instructions

• Powering on/off the device
  • To power on the device, locate the power button on the front panel and press it. The device will then start up and be ready for use. To power off the device, press and hold the power button for 3 seconds until the device shuts down completely.
• Operating the device
  • The device can be operated using the control buttons located on the top panel. The buttons include:
  • Button A: Perform action X
  • Button B: Perform action Y
  • Button C: Perform action Z
  • To use a specific function, press the corresponding button. The device will respond accordingly.
• Charging the device
  • To charge the device, connect the provided charging cable to the charging port located on the bottom of the device.
  • Plug the other end of the cable into a power source, such as a USB port or wall adapter. The device will start charging automatically. A full charge takes approximately 2 hours.
• Maintenance and care
  • To ensure optimal performance and longevity of the device, follow these maintenance guidelines:
  • Keep the device clean by wiping it with a soft, dry cloth.
  • Avoid exposing the device to extreme temperatures or humidity.
  • Avoid dropping or subjecting the device to impact.
  • Store the device in a cool and dry place when not in use.
• Frequently Asked Questions (FAQ)
  • Q: How long does the battery last on a full charge?
  • A: The device can operate for up to 8 hours on a full charge.
  • Q: Can I use the device while it is charging?
  • A: Yes, you can use the device while it is charging.
  • Q: How can I check the battery level?
  • A: Press and hold the power button for 3 seconds. The device will indicate the battery level through a series of LED lights.

Warranty Registration

• Congratulations on your purchase of a Guardian SN35P dehumidifier.
• Your new dehumidifier comes with an extensive warranty program.
• To register, simply complete and return the warranty form provided in the dehumidifier box.
• Be sure to include your dehumidifier’s serial number. as you will need it to register.

Safety Notes

• The Guardian SN35P dehumidifier must always use a grounded electrical connection (as required for all appliances). If a non-grounded wire is used, all liability goes to the buyer and the warranty is void.
• Your new dehumidifier comes with an extensive warranty program. To register, simply complete and return the warranty form provided in the dehumidifier box.
• Be sure to include your dehumidifier’s serial number as you will need it for registration.
• The Guardian SN35P dehumidifier should be maintained and repaired by a qualified technician.
• The Guardian SN35P dehumidifier is intended for operation when the unit is standing and horizontal only. Operating the unit in any other direction may allow water to flood the electrical components.
• Always unplug the dehumidifier before moving.
• If water threatens to food the dehumidifier, turn off and unplug the dehumidifier.
• To ensure proper operation, the dehumidifier’s air inlet and air outlet should be at least 6 feet away from a wall or any obstruction.
• Do not insert fingers or any objects into the inlet or outlet holes.
• The dehumidifier should be turned OFF and unplugged when performing maintenance or repair.
• Before repairing the dehumidifier, contact our customer support team. Some procedures must be performed by a qualified technician.
• Do not use water to clean the exterior of the machine. To clean the unit, unplug the power and wipe the exterior with a damp cloth.
• Do not stand on the machine or use it as a device for hanging clothes.

Identification

Please write down the model number, serial number and date of purchase of the dehumidifier for future reference. If you need to ask for help in the future. This is very useful. The data label on the side of the unit has the key features of the particular machine.

• Model Number: Guardian SN35P
• Serial Number:
• Date of Purchase: For additional questions about your dehumidifier, email sales@abestorm.com.

Electrical Supply

• Power supply: 115V, 60HZ AC, single phase
• Outlet requirements: 3 holes, GFCI
• Circuit protector: 15 amps
• Warning: 240 volts AC power may cause serious injury due to electric shock.

To reduce the risk of injury:

1. Disconnect the power supply before servicing.
2. Only plug the device into a grounded circuit.
3. Do not use extension cords.
4. Do not use plug adapters.

Principle of Operation

• The Guardian SN35P dehumidifier reads the relative humidity in the room.
• When the detected relative humidity exceeds the humidity setpoint, the dehumidifier will automatically turn on.
• The air passes through the evaporator coil, which is cooler than the dew point of the air.
• This means that moisture condenses out of the air. The air is then reheated through the condenser coil and distributed back into the room.

Installation

The area to be controlled should be sealed with a vapor barrier. If the equipment is installed in a confined space, all vents should be sealed.
WARNING: Do not install the dehumidifier in a corrosive environment. Some liquid vapor barriers dry by “solvent evaporation”. Always make sure the barrier is completelydry.

• Step 1: Place the dehumidifier on a level surface.
  • Do not place the dehumidifier directly on the vapor barrier. It is suggested to place the dehumidifier on a level block or paver.
  • Wait for at least 12 hours before turning on the dehumidifier after delivery.
• Step 2: Set up the drain line.
  • Remove the nut from the drain nozzle before connecting the drain hose when using the dehumidifier’s pump drain system.
  • To use the gravity drain system, locate the other drain nozzle on the side of the unit. Remove the drain plug and connect the drain hose (with a larger inner diameter) onto the other drain nozzle.
• Step 3: Plug the unit into a 15-amp ground circuit.

Key Functions

1. The “ON /OFF” Button
   • Press this button to turn ON/OFF the dehumidifier.
   • When the dehumidifier is turned off, there would be a 120-second delay on the fan. Do not unplug the unit until the fan is off.
2. “SET” Button
   • This button is used to change the humidity setpoint from 25% to 80%. The dehumidifier may also be set at “CO” or Continuous Operation mode to run the dehumidifier continuously. The setpoint has 5% increments of each press.
3. “Drain” Button
   • Hold this button down for at least 3 seconds to switch the drain system to use. Either pump drain system or gravity drain system.
4. Water Pump Drainage Mode:

   •   * If the “Pump” light is turned ON, it indicates that the pump drain system is in use. (The gravity drain nozzle must be blocked to cover the drain hole)

   • The “Drain” button can be pressed once to force the water pump to remove the collected moisture from the water tray for 14 seconds. During pump operation, this button is not valid.
   • If the water pump float switch detects a high level of water in the tray, the pump will automatically run and drain the collected moisture for 14 seconds. If a high level of water is still detected, after the pump runs for 14 seconds, the screen will display an “E4” error code.
5. Gravity Drainage Mode:

   •   * If the “Pump” light is turned OFF, it indicates that the gravity drain system is in use. The system. i sense dentate to then drain the moisture so let drain

   • If a high level of water is detected by the float switch for 14 seconds, the screen will display an “E4” error code and the dehumidifier will STOP from running to avoid a water leak.
   • Note: When moving the machine from one location to another, wait at least 10 minutes after turning it off. This will allow the moisture in the coil to drip down in the removal are collected moist the or water comprehe direction of the drain hole to
6. ” GPP” button
   • This button is used to change the humidity reading from RH% to GPP (Grains per pound). GPP is the unit used to measure the weight of moisture in the air. The number of grains per pound of dry air expresses the specific humidity of the air. The GPP setpoint can be set at 25 to 200.
   • Relative humidity (RH) refers to the moisture content of the atmosphere, expressed as a percentage of the amount of moisture that can be retained by the atmosphere at a given temperature and pressure with condensation.
7. “SET +Drain” key
   • The SET + Drain key combination is used to display the temperature of the temperature sensor by pressing and holding for 3 seconds. “SET +GPP” key
   • “SET + GPP” key combination press for 3 seconds to display the temperature of the coil in Celsius.

Indicator lights

1. Humidity display screen
2. The display screen has two functions
3. By default, the screen displays the Relative humidity level in the space.
4. While setting the humidity setpoint, the screen displays the current setpoint. After 2-3 seconds, the display will return to the default screen to display the Relative humidity level in the space.
5. Operation Indicator Power
   • When the power light is solid green, it indicates that the dehumidifier is turned on. If this light is flashing, it means that the dehumidifier has reached the desired humidity setpoint.
6. Continuous mode light Continue
   • When this light is on green, it indicates that the dehumidifier is set to continuous operation mode. In continuous mode of operation, this light is always on, in other states, this light is off.
7. Water Pump Drainage Pump
   • In water pump mode, this light is on; in gravity drainage mode, this light is off. The factory default mode of the device is gravity drainage mode
8. GPP mode indicator GPP
   • When the compressor is in GPP mode, this light is on; in regular mode, this light is off

Remote Control Instructions

• The Abestorm 35P dehumidifier can be controlled using the (optional) wired remote accessory.
• It is connected via a 25-inch CAT5 Cable.
• The remote control contains an integrated sensor which also detects the temperature and humidity level of the room where the remote controller is placed in

1. On/Off Power (Button)
   • Press the on/off button and the machine will start running . Press the button again to turn off the machine.
2. Up Button / Down Button
   • Use the up and down arrow buttons to adjust the humidity level.
3. Mode M
   • Use the Mode button to switch between dehumidification and a ducted application.
   • The symbol on the display board indicates the sensor on the remote control is being utilized.
   • The symbol on the display board indicates the sensor on the dehumidifier is being utilized.
4. Temperature T
   • Press the temperature button to display the current temperature on the screen. The T button toggles the temperature scale setting back and forth °C / F°.
5. Continuous C
   • Pressing this button will switch the unit to continuous mode. cont will appear on the display to indicate continuous mode.
6. Drain Pump P
   • Press this button to drain or pump the collected moisture or water out of the dehumidifier.
   • NOTE: The above symbol will only appear when the dehumidifier is powered on. (Pressing the P button screen displays Draining indicating that it is draining and disappears when the drainage is complete.

Dehumidifier Diagram

Maintenance

WARNING: Always unplug the power before performing any maintenance.
Cleaning the body

• Use a soft damp cloth to clean the exterior of the unit. Do not use any soap or solvent.

Coil Maintenance

• Once a year, clean coils with an approved coil cleaner.
• Coil cleaner should be a self-cleaning, foaming cleaner such as WEB® Coil Cleaner.

Dehumidifier Storage
If the unit will be stored for an extended period, complete the following steps:

1. Turn the unit off and allow it to dry.
2. Pack and secure the power cord.
3. Cover the filter.
4. Store in a clean, dry place.

Troubleshooting

Pump Alarm Trouble Code E4

1. Reset the unit by disconnecting the power cord, then reconnecting it.
   • NOTE: The unit will not work until the error code is cleared.
2. Manually check if the pump is operational by pressing the drain button. Check that the pump is properly powered on and off. Also, check to see if any water is draining from the unit.
3. If tecte balance of the pumpse rem see Maintena dis on page for detailstions, then If maintenance alone is not enough, the hoses and/or pumps can be replaced

Maintenance and Application

Maintenance and application of water pumps
Normal use of the water pump

1. To verify if the drain button is functional.
   When the power is on, press the drain button. If the collected moisture is properly drained through the water tray nozzle, this indicates that the condensate pump is not defective.

2. To verify if the automatic drain system is functional.
   When the dehumidifier automatically activates the pump after a certain amount of moisture is collected, this indicates that the float switch is working properly.

3. Pump Error.
   In the event of a pump failure, the screen will display a “E4” Error code to stop the dehumidifier from running to prevent water leak.

Use of gravity drainage pipe (gravity drainage or pump drainage can be selected according to the working environment) When the gravity drain system is in use, elevate the unit from the ground. This can be done by hanging the dehumidifier on the floor joist or using a level object to place the water leak.

Water pump fault judgment and maintenance methods
Judgment of the problem when the error code “E4” appears.

1. The drainage hose is blocked by foreign objects or bent and deformed
2. The drainage height exceeds the standard.
3. Water level switch failure.
4. The water pump is malfunctioning or its service life has expired.
5. The internal water pump hose is blocked or bent or deformed by foreign objects.

Water pump repair method

1. Use a Phillips screwdriver to unscrew the screws on the water pump panel, and you can see the fixed status of the water pump.
2. Use a Phillips screwdriver to unscrew the screw of the pump fixing bracket.
3. Pull out the hose fixed in the water reservoir and take out the water pump for replacement.
4. Follow the above steps to install the new water pump to the original position.

Spare Parts

Guardian SN35P Spare Parts

Limited Warranty

• This limited warranty period begins on the date of purchase Abestorm warrants to the original purchaser that during the following limited warranty period, the Abestorm product is free from manufacturing defects in material or workmanship. six (6) months for parts and labor.
• This includes the cost of shipment of replacement parts or equipment. One (1) year for parts and labor.
• This does not include the cost of shipping the defective product back for repair or replacement.
• Three (3) years of parts and labor on the refrigeration system only (compressor, condenser, and evaporator). Transportation costs are not included.
• Five (5) year parts only on the refrigeration system (compressor, condenser, and evaporator). Shipping costs are not included.
• This limited warranty applies only to units purchased from the manufacturer or an authorized Abestorm dealer and purchased following the instructions contained in this User’s Guide or with the product for operation, installation and maintenance.
• Alestorm will not provide home service during or after the warranty period. You may be responsible for shipping costs to bring the product to the manufacturer for service
• To obtain warranty service, the buyer must contact Abestorm at 888-276-9833 or sales@abestorm.com.
• Warranty service requires proof of purchase or order number. During the applicable warranty period, a product will be repaired or replaced at the sole option of Abestorm.

IMPORTANT NOTICE: Keep the item’s packaging in case warranty service is required.

Limited Warranty Exclusions

This limited warranty covers manufacturing defects in materials or workmanship encountered in the normal domestic, commercial, or non -non-commercial use of this product Defects, excluding the following.

• Damage caused by this product during unintended use.
• Damage caused by unauthorized modification or alteration of the product.
• Cosmetic damage, including scratches, dents, chips, and other damage to the finish of the product.
• Damage is caused by abuse, misuse, pests, accidents, fire, floods, or other acts of nature.
• Damage is caused by abuse, misuse, pests, accidents, fire, floods, or other acts of nature.
• Damage is caused by incorrect line currents, voltages, fluctuations, and surges.
• Damage caused by failure to properly maintain the product.

The Use of this product in SPA or a room with an outdoor pool invalidates or voids the limited warranty.

WIRING

WARRANTY REGISTRATION CARD

• If you have any questions, please feel free to contact us at (888)276-9833 or visit www.abestorm.com.
• Register your unit for warranty using this link: https://www.abestorm.com/service-warranty.

Abestorm Solutions INC.

• Add: 8605 SANTAMONICABLVD#79525
• WEST HOLLYWOOD, California,90069 USA
• E-mail: sales@abestorm.com.

Note: as we keep upgrading our product, we reserve the right to modify the product without notice in advance

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>