tala CP-BLK-LRG-BS-01-US Basalt Nine Pendant Installation Guide
- June 3, 2024
- TALA
Table of Contents
INSTALLATION GUIDE
Basalt Nine Pendant
Thoughtful lighting, responsibly designed in London.
Thank you for making the switch to Tala.
Discover the full Tala family at us.tala.co.uk
BEFORE STARTING
We recommend the installation of our canopy and pendants is performed by a qualified electrician. Please read the instructions thoroughly before commencing work and keep them for future reference. Please take extreme care when carrying out these instructions.
IMPORTANT
This light fitting must be connected to the earth supply. If your lighting
circuit does not have earth, ask a qualified electrician to provide an earth
facility. This light fitting is suitable for indoor use only. This fitting
operates on 120V mains voltage. For a list of recommended dimmers to pair with
this light fitting, please visit our website.
WARNING
You must switch off the electricity supply at the mains during installation
and maintenance. We strongly recommend that you withdraw the fuse or switch
off the circuit breaker whilst work is in progress. Do not only turn off the
wall switch. All fittings must be installed in accordance with current
Building Regulations and IEE Wiring Regulations.
RECOMMENDED EQUIPMENT
– Small Flat-head and Phillips-head screwdrivers
– Wire strippers
– Insulation tape
Further equipment may be required for fixing to your ceiling.
BASALT NINE PENDANT – COMPONENTS
STEP 1
Attach A to the ceiling using screws and a plug. Make sure to use screws
and plugs that are appropriate for the ceiling type.
STEP 2
Attach ceiling plate B to ceiling bracket A using safety tether clips D
STEP 3
Thread all nine pendant cables F though ceiling plate cord grips C
STEP 4
Pull cables through to your desired length. Using a flathead screwdriver,
tighten set screws C to secure them.
STEP 5
Cut off excess cable and strip wires to expose the copper core. Maintain all
double insulation.
STEP 6
Connect the pendants, plate and mains wiring as shown.
STEP 7
Lift to B sit flush with| A
Make sure pins 1 are located at the opening of the bayonet fitting . 2
STEP 8
Rotate plate B anti-clockwise until the pin is locked into the 1 bayonet
mechanism 2
Secure plate B in place using bolt H
STEP 9
Lift the metal pendant sleeve F and screw the bulb firmly into the socket.
Take care to prevent the metal sleeve from dropping onto the glass bulb.
STEP 10
Rotate metal sleeve F to align with the contours of the bulb. Carefully lower
the metal sleeve F to sit flush with the bulb and make final tweaks to the
alignment to achieve the intended design.
PENDANTS DISPLAY GUIDE
MINIMUM CORD LENGTH A
For all bulbs shortest recommended cord length is 350mm
DISTANCE BETWEEN PENDANTS B
The recommended minimum distance between pendants is 100mm
PENDANTS – RECOMMENDED CABLE LENGTHS
SCENARIO 1
Above a coffee or dining table, or where height is required for seated tasks
SCENARIO 2
Above side tables, or where height is required for storage
SCENARIO 3
Above a kitchen island or bar, or where height is required for standing tasks
SCENARIO 4
Above a stairwell or walkway, or where height is required for walking
underneath
CARE AND CLEANING
We recommend cleaning with a soft dry cloth. Do not use abrasive materials as these will damage the finish of the product. Do not expose any part of the bulb or pendant to water or moisture.
WARRANTY AND AFTER-CARE
This product is covered by a three-year warranty. Within this time, we will replace any parts that show functional defects or malfunctions. Please report any signs of fault or damage to our Customer Service team, along with supporting visual evidence, by emailing: customerservice@tala.co.uk.
Join the Community
hello@tala.co.uk | Instagram: @tala | Facebook:
talaHQ | Pinterest: TalaLED | Tag: lighttoliveby
Tala North America, Inc. P.O. Box 89, 1051 Port Washington Blvd. Port
Washington, NY 11050
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>