3onedata IES2300SL Series Unmanaged Industrial Ethernet Switch Installation Guide
- June 1, 2024
- 3onedata
Table of Contents
- Package Checklist
- Product Overview
- Panel Design
- Front view
- Mounting Dimension
- DIN-Rail Mounting
- Disassembling DIN-Rail
- Power Supply Connection
- DIP Switch Settings
- Checking LED Indicator **
- Specification
- Disposal of Waste Electrical and Electronic Equipment (WEEE 2012/19/EU)
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
3onedata IES2300SL Series Unmanaged Industrial Ethernet Switch Installation
Guide
Package Checklist
Please check the integrity of package and accessories while first using the switch.
- Industrial Ethernet
- DIN-Rail mounting switch attachment
- Certification
- Warranty card
If any of these items are damaged or lost, please contact our company or dealers, we will solve it ASAP.
Product Overview
This series of product is Gigabit unman aged DIN-Rail industrial Ethernet switch. For convenience, the products of this series adopt the following number on the left in this guide, please affirm the number of your product.
Model I. IES2300SL-5GT-2LV (5 Gigabit copper ports, 12/24/48VDC redundant
power supply input).
Model II. IES2300SL-8GT-2LV (8 Gigabit copper ports (two-row RJ45),
12/24/48VDC redundant power supply)
Model III. IES2301SL-8GT-2LV (8 Gigabit copper ports (single-row RJ45),
12/24/48VDC redundant power supply)
Model IV. IES2300SL-16GT-2LV (16 Gigabit copper ports, 12/24/48VDC
redundant power supply input).
Panel Design
Top view, bottom view and rear view
Front view
Model I Model II Model III Model IV
- Terminal blocks for power input (P1-P2)
- DIP switch
- Grounding screw
- DIN-Rail mounting kit
- Location hole for wall-mounting panel
- Ethernet port indicator (G1-G5/G8/G16)
- Running indicator (RUN)
- Power supply indicator (P1-P2)
- 10/100/1000Base-T(X) Gigabit (G1-G5/G8/G16)
Mounting Dimension
**Model I
Model II
Model III, Model IV
**
Notice Before Mounting:
- Don’t place or install the device in area near water or moist, keep the relative humidity of the device surrounding between 5%~95% without
- condensation. Before power on, first confirm the supported power supply specification to avoid over-voltage damaging the device.
- The device surface temperature is high after running; please don’t directly contact to avoid scalding
DIN-Rail Mounting
The product adopts 35mm standard DIN-Rail mounting which is suitable for most
industrial scenes, mounting steps as follows:
Step 1 Check if the DIN-Rail mounting kit is installed firmly.
Step 2 Insert the bottom of DIN-Rail mounting kit (one side with spring
support) into DIN-Rail, and then insert the top into DIN-Rail.
Tips: Insert a little to the bottom, lift upward and then insert to the
top.
Step 3 Check and confirm the product is firmly installed on DIN-Rail,
then mounting ends.
Disassembling DIN-Rail
Step 1 Power off the device.
Step 2 After lifting the device upward slightly, first shift out the top
of DIN-Rail mounting kit, and then shift out the bottom of DIN-Rail,
disassembling ends.
Notice before power on:
- Power ON operation: First insert the power supply terminal block into the device power supply interface, then plug the power supply plug contact and power on.
- Power OFF operation: First, remove the power plug, then remove the wiring section of terminal block. Please pay attention to the above operation sequence.
Power Supply Connection
Support 2 power inputs, and adopt 4-pin 5.08mm pitch terminal blocks. The power input supports 1 power supply alone or 2 power supply at the same time; When two power supply input at the same time, it supports redundant backup of power supply. If one power supply fails, the device can still work normally without interruption. Power supply supports anti-reverse connection, which cannot power the device but won’t damage it when it’s reversely connected. The definitions of power pin are shown in the figure above, and the power input range is 12/24/48 VDC (49~60VDC).
DIP Switch Settings
This series provide 4-pin DIP switch for function setting, where “ON” is the enabled end. The definitions of DIP switch are as follows:
Model I
No. | Definition | Operation |
---|---|---|
1 | Forced 100M be forced to be | Set the switch to ON, Port 1-5 would in 100M |
2 | Storm Set the Suppression su | switch to ON to enable storm oppression |
function
3| VLAN| Set the DIP switch to ON, Port 1 linkup port, Port 2-5 are the down
link
No.| Definition| Operation
| | ports, and the down link ports are isolated from each other.
4| Flow control| Set the switch to ON to enable flow control function.
Model II Model III
ON | Definition | Operation |
---|---|---|
1 | Forced Set th be forced to b | e switch to ON, Port 1-8 would 100M e in 100M |
2 | Storm Set the Suppression | switch to ON to enable storm suppression |
function
3| Davenports, and the isolated from| Set the DIP switch to ON, Port 1 is up
link port, Port 2-8 are the down link down link ports are each other.
4| Set the switch Flow control control function| h to ON to enable flown.
Model IV
No. | Definition | Operation |
---|---|---|
1 | Loop Set the Detection loo | switch to ON to enable port p detection |
function.
2| Storm Set the Suppression| switch to ON to enable storm suppression
function.
3| Set the DIP sear up link pro VLAN are isolated fr| witch to ON, Port 1- 2
ts, Port 3-16 are the down link ports, and the down link ports om each other.
4| Set the switch Flow control control function| h to ON to enable flow on.
Checking LED Indicator **
**
The device provides LED indicators to monitor its operating status, which has simplified the overall troubleshooting process. The function of each LED is described in the table below:
LED | Indicate | Description |
---|---|---|
P1-P2 | ON | Power is connected and running normally |
OFF | Power supply is disconnected or running abnormally The device is powering |
on or
RUN| ON| the device is abnormal.The device is running
Blinking| normallyThe device is powered off or
OFF| the device is abnormal.Ethernet port has established
G1-G5/G8/G16| ON| a valid network connectionEthernet port is in an active
network status
Blinking| Ethernet port has not established a valid network
OFF| connection
Specification
Pan|
---|---
| 00 Base-T(X) self- adapting RJ45 port, half/full duplex self-adaption or
forced working mode, support MDI/ MDI-X self-adaption
Indicator| Power indicator, running indicator, interface indicator
Switch Property|
Model I| Back plane bandwidth: buffer size: 2Mbit MAC address table: 2K
Model II Model III| Back plane bandwidth: 16G Buffer size: 1.5Mbit MAC address
table: 4K
Model IV| Back plane bandwidth: 52G Buffer size: 4.1Mbit MAC address table: 8K
Power supply|
Input power supply| 12/24/48 VDC(9~60VDC), dual power supply
redundancy, support anti-reverse connection
---|---
Access terminal block| 4-pin 5.08mm pitch terminal blocks
Power Consumption|
Model I| No-load: 0.2W@12VDC
Full-load: 1.6W@12VDC
Model II, Model
III Model IV| No-load: 0.4W@12VDCFull-load: 3.0W@12VDC
| No-load: 3.3W@48VDCFull-load: 10.4W@48VDC
Working Environment|
Working temperature| -40~75
Storage temperature| ℃ -40~85
Working humidity| ℃ 5%〜95% (no condensation)
Protection grade| IP40 (metal shell)
Disposal of Waste Electrical and Electronic Equipment (WEEE 2012/19/EU)
Applicable in the EU-member states)
The crossed-out wheeled bin symbol on the equipment or its packaging indicates
that the product, at the end of its service life, shall not be mixed with
unsorted municipal waste but should be collected separately, in accordance
with local laws and regulations
A proper separate collection of end-of-life equipment for the subsequent
recycling, treatment and environmentally compatible disposal, will help
prevent potential damage to the environment and human health, facilitating the
reuse, recycling and/or recovery of its component materials.
Private users should contact their vendor or municipal waste management
service and ask for disposal information.
Professional users should contact their suppliers and check the terms of their
selling agreement.
This product must not be disposed of with other commercial waste.
Users’ cooperation in the correct disposal of this product will contribute to
saving valuable resources and protecting the environment.
Bonedata Co., Ltd.
Address: 3/B, Zone 1, Baiwangxin High Technology Industrial Park, Xili,
Nanshan District, Shenzhen
Website: www.3onedata.com
Tel: +86 0755-26702688
Fax: +86 0755-26703485
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>