3onedata CP202-2CI-P Can Server Ethernet converter Installation Guide

June 14, 2024
3onedata

**3onedata CP202-2CI-P Can Server Ethernet converter Installation Guide

**

Product Installation Instruction

Package Checklist

Please check the integrity of package and accessories while first using the CAN server.

  1. CAN server X1 (with wiring terminal block)
  2. Straight-through network cable
  3. Wall mounting accessories
  4. Power adapter
  5. Warranty card
  6. Certification

If any of these items are damaged or lost, please contact our company or dealers, we will solve it ASAP.

Products Overview

This product is a CAN server, the model is CP202-2CI-P (12- 48VDC) (2 CAN bus ports to 1 10/100 Base T(X) converter).

Panel Design

Top view, main view and bottom view

  1. Terminal block for power input
  2. Restoring factory setting button Setup
  3. 100M Ethernet RJ45 port
  4. Indicators, from top to bottom in turn they are:
    • Power indicator PWR
    • system running indicator RUN
    • network link indicator LINK
    • CAN port error indicator ERR1
    • CAN port state indicator CAN1
    • CAN port error indicator ERR2
    • CAN port state indicator CAN2
  5. Lugs
  6. CAN0/terminal block
  7. CAN1/terminal block
  8. DIP switch

Mounting Dimension

Unit : mm

Notice Before Mounting:

  • Don’t place or install the device in area near water or moist, keep the relative humidity of the device surrounding between 5%~95% without condensation.
  • Before power on, first confirm the supported power supply specification to avoid over-voltage damaging the device.

Wall-mounted Device Mounting

Step : 1 Place the CAN server on the wall as reference or reference installation dimension; label the bolt position on the wall.
Step : 2 Nail M 4 screws on the wall and keep 2mm inter space reserved.
Step : 3 Hang the device on two screws and slide downward, then tighten the screw to enhance stability, mounting ends.

Device Disassembling

Step : 1 Power off the device.
Step : 2 Unscrew the screw on the wall about 2mm.
Step : 3 Lift the device outward slightly; take out the device, disassembling ends.
Notice before power on :

  • Power ON operation: First insert the power supply terminal block into the device power supply interface, and then plug the power supply plug contact and power on.
  • Power OFF operation: First, remove the power plug, then remove the wiring section of terminal block. Please pay attention to the above operation sequence.

Power Supply Connection

DC power supply
The device supports 1 DC power input, adopts 3-pin 5.08mm pitch terminal blocks (V+, FG, V-), FG is the ground terminal, power input range:
12 〜 48VDC. The power supply supports non-polarity connection, and the equipment can still work normally after reverse connection.

Restore Default Settings

Setup is restoring default settings button. Restoring default settings steps as follows: Press and hold the Setup button, wait for 4-5 seconds, then release the button to restore the factory settings.

DIP Switch Settings

The device provides two-pin DIP switch, in which switch 1 corresponds to CAN1 and switch 2 corresponds to CAN 2.

Number Definition Operation
1 Add 120Ω terminal resistance to CAN1 Set Switch1 to ON
2 Add 120Ω terminal resistance to CAN2 Set Switch2 to ON

CAN Port Connection

The device provides 2 CAN ports, adopts 6-pin 5.08mm pitch industrial terminal blocks, in which Pin 1-3 are the first CAN port and Pin 4-6 are the second CAN port. The pin definition as follows :

NO. Name Note
1 CAN1H The first channel CANH signal The
2 CAN1L first channel CANL signal Shell
3 GND Ground
4 CAN2H The second channel CANH signal
5 CAN2L The second channel CANL signal
6 GND Shell Ground

LED Indicator

The device provides LED indicators to monitor its operating status, which has simplified the overall troubleshooting process. The function of each LED is described in the table below :

LED Indicate Description
P W R ON Power  is  connected  and  running normally
OFF Power supply is disconnected or running abnormally
RUN Blinking The system is running normally
OFF The system is not running or running abnormally
ON LAN port has established valid network connection
LINK ON LAN port has established valid network connection
Blinking LAN port is in an active network status
OFF LAN port hasn’t established valid network connection
ERR1 ON CAN1 port work has fault
OFF CAN1 port is working normally
CAN1 OFF CAN1 port is not transmitting data or transmitting data abnormally
Blinking CAN1 port is transmitting data
ERR2 ON CAN2 port work appears fault
OFF CAN2 port is working normally
CAN2 OFF CAN2 port is not transmitting data or transmitting data abnormally
Blinking CAN2 port exists data transmission

Logging in to WEB Interface

This device supports WEB management and configuration.
Computer can access the device via Ethernet interface. The way of logging in to device’s configuration interface via IE browser is shown as below.

Step : 1 Configure the IP addresses of computer and the device to the same network segment, and the network between them can be mutually accessed.
Step : 2 Enter device’s IP address in the address bar of the  computer browser.  http://192.168.1.254/
Enter device’s username and password in the login window as shown below.

Step : 4 Click “Login” button to login to the WEB interface of the device.
Notes :

  • The default IP address of the device is “192.168.1.254”.
  • The default user name and password of the device are “admin”.
  • If the user name or password is lost, user can restore it to factory settings via Setup button or management software; all modified configurations will be cleared after restoring to factory settings, so please backup configuration file in advance.
  • Please refer to user manual for specific configuration method of logging in to WEB interface and other configurations about network management function.

| indicator,  CAN   port  errorindicator,  CAN   port  state indicator
---|---
Power Supply
Input power supply| 12V〜48VDC
Access terminal block| 3-pin 5.08mm pitch industrialwiring terminal blocks
Power Consumption
No-load| 1.00W@12VDC
Full-load| 1.10W@12VDC
Working Environment
Working temperature| -40℃〜75℃
Storage temperature| -40℃〜85℃
Working humidity| 5%〜95% (no condensation)
Protection grade| IP40 (metal shell)

Specification

Panel

100M copper port| 10/100 Base-T(X)self-adapting RJ45 port, full duplex or half duplex self- adapting, support MDI/MDI-X self-adapting
CAN Port| 2 CAN ports, 6-pin 5.08mmpitch industrial wiring terminal blocks
Indicator| Power    indicator,    systemrunning indicator, network link


3onedata Co., Ltd.
Address : 3/B, Zone 1, Baiwangxin High Technology
Industrial Park, Xili, Nanshan District,

México
+ 52 (33) 3854 5975
ventas@logicbus.com
www.logicbus.com.mx
USA
+1 (619) 619 7350
saleslogicbus.com
www.logicbus.com
Shenzhen
Website : www.3onedata.com
Tel: +86 0755-26702688
Fax: +86 0755-26703485

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

3onedata User Manuals

Related Manuals