3onedata IES6306 Series Managed Industrial Ethernet Switch Installation Guide

June 13, 2024
3onedata

3onedata Logo IES6306 Series
Managed Industrial Ethernet Switch
Quick Installation Guide

Package Checklist

Please check the integrity of package and accessories while first using the switch.

  1. Industrial Ethernet switch
  2. Certification
  3. Quick installation guide
  4. Warranty card
  5. DIN-Rail mounting attachment
  6. CD

If any of these items are damaged or lost, please contact our company or dealers, we will solve it ASAP.

Product Overview

This series product is Gigabit managed DIN-Rail industrial Ethernet switch. The model is:

Model I.| IES6306-4GT2HS-2P48 (4 Gigabit Copper Ports + 2 2.5G SFP + 2 12~48 Power Supplies)
---|---
Model II.| IES6306-4GP2HS-2P48-120W (4 Gigabit PoE Copper Ports + 2 2.5G SFP + 2 48VDC PoE Power Supplies)

Panel Design

 Top view, bottom view and rear view

3onedata IES6306 Series Managed Industrial Ethernet Switch -
bottom

 Front View

3onedata IES6306 Series Managed Industrial Ethernet Switch -
Model

  1. Power input terminal (P1, P2)
  2. Relay alarm output terminal block
  3. DIP switch
  4. Console port
  5. Grounding screw
  6. Location hole for wall mounting
  7. DIN-Rail mounting kit
  8. Power input status indicator P1-P2
  9. Relay alarm indicator ALM
  10. Device running indicator RUN
  11. 2.5G SFP slot (5-6)
  12. Copper port (1-4)
  13. Ethernet interface status indicator (1-6)
  14. Gigabit PoE port (1-4)
  15. PoE status indicator (1-4)

Mounting Dimension

Unit: mm

3onedata IES6306 Series Managed Industrial Ethernet Switch -
Dimension

Notice Before Mounting:

  • Don’t place or install the device in area near water or moist, keep the relative humidity of the device surrounding between 5%~95% without condensation.
  • Before power on, first confirm the supported power supply specification to avoid over-voltage damaging the device.
  • The device surface temperature is high after running; please don’t directly contact to avoid scalding.

DIN-Rail Mounting

The product adopts 35mm standard DIN-Rail mounting which is suitable for most industrial scenes, mounting steps as follows:

3onedata IES6306 Series Managed Industrial Ethernet Switch -
DIN

Step 1 Check if the DIN-Rail mounting kit is installed firmly.
Step 2 Insert the bottom of DIN-Rail mounting kit (one side with spring

support) into DIN-Rail, and then insert the top into DIN-Rail.
Tips: Insert a little to the bottom, lift upward and then insert to the top.
Step 3| Check and confirm the product is firmly installed on DIN-Rail, then mounting ends.

Disassembling DIN-Rail

Step 1 Power off device.
Step 2 After lifting the device upward slightly, first shift out the top of

DIN-Rail mounting kit, and then shift out the bottom of DIN-Rail, disassembling ends.

Notice before power on:

  • Power ON operation: First insert the power supply terminal block into the device power supply interface, and then plug the power supply plug contact and power on.
  • Power OFF operation: First, remove the power plug, and then remove the wiring section of terminal block. Please pay attention to the above operation sequence.

Power Supply Connection

Model I
This Model I device provides 6-pin 5.08mm pitch input terminal blocks, including 4 pins power supply terminal blocks on the left side. It provides two independent DC power supply systems of P1 and P2. The power supply supports non-polarity and anti-reverse connection, which can ensure the normal operation of the device after it’s reversely connected. Voltage range 12~48VDC.

3onedata IES6306 Series Managed Industrial Ethernet Switch - DC
powe

This Model II device provides 6-pin 5.08mm pitch input terminal blocks, including 4 pins power supply terminal blocks on the left side. It provides two independent DC power supply systems of P1 and P2. The power supply supports anti-reverse connection, which can prevent device from damage after it’s reversely connected, but it cannot be powered on. Voltage range is as below:

  • Voltage range without using PoE function: 12~48VDC
  • Rated voltage: 48VDC
  • Maximum voltage range: 44VDC-55VDC

3onedata IES6306 Series Managed Industrial Ethernet Switch -
device

Relay Connection

This series device provides 6-pin 5.08mm pitch input terminal blocks, and the relay occupies the right 2 pins. Relay terminals are a set of normally open contacts of the device alarm relay. They are open circuit in the state of normal non alarm, closed when any alarm information occurs. For example, they are closed when powered off, and send out alarm. The switch supports 1 relay alarm information output that can output DC power supply alarm information or network abnormality alarm. It can be connected to alarm light or alarm buzzer or other switching value collecting devices, which can timely inform operators when the alarm occurs.

3onedata IES6306 Series Managed Industrial Ethernet Switch -
Connection

DIP Switch Settings

Provide 4 pins DIP switch for function settings, where “ON” is enable valid terminal. The device needs to be powered on again to change the status of DIP switch.
DIP switches definition as follows:

DIP Definition Operation
1 Restore Factory Settings Set the DIP switch to ON, the device will root

automatically and restore to factory settings, then turn off the DIP
switch.
2| Reserved| –
3| Reserved| –
4| Reserved| –

Checking LED Indicator
The device provides LED indicators to monitor the device working status with a comprehensive simplified troubleshooting; the detailed status of each LED is described in the table as below:

LED Indicate Description
P1 ON P1 is connected and running

normally
OFF| P1 is disconnected and running
abnormally
P2| ON| P2 is connected and running
normally
OFF| P2 is disconnected and running
abnormally
ALM| ON| Power supply link has alarm
OFF| Power supply link have no alarm
RUN| ON| The device is powered on or the
device is abnormal.
OFF| The device is powered off or the
device is abnormal.
Blinking| Blinking 1 time per second, the
device is running well.
Link/Act
(1-6)| ON|  The Ethernet interface has
established a valid network connection.
Blinking| The Ethernet interface is in anetwork activity state.
OFF| The Ethernet port has not
established a valid network
connection
PoE(1-4)| ON| PoE port is powering PD normally
Blinking| PoE port is in the detection or fault
OFF| state

Specification

Panel|
---|---
2.5G SFP slot| 100/1000 Base-X self-adaption or 100/1000/2.5G Base-X forced mode, SFP slot
Gigabit copper port| 10/100/1000 Base-T(X) self-adapting RJ45 port, half/full duplex self-adaption or forced working mode, support MDI/ MDI-X self-adaption
Gigabit PoE port| 10/100/1000 Base-T(X) self-adapting RJ45 port, half/full duplex self-adaption or forced working mode, support MDI/ MDI-X self-adaption; the single port supports up to 30W PoE output power, PoE power supply pin: V+, V+, V-, V- correspond to Pin 1, 2, 3, 6
Console port| CLI command management port (RS-232), RJ45
Alarm interface| 6-pin 5.08mm pitch terminal blocks, alarm occupies 2 pins and 1 relay alarm information output is supported, the current load capability is 1A@30VDC or 0.3A@125VAC
Indicator| Power supply indicator, run indicator, interface indicator, alarm indicator, PoE interface indicator
Switch Property|
Backplane bandwidth| 30G
Packet buffer size| 4Mbit
MAC Address Table| 8K
Power Supply|
Model I| 12~48VDC
Support dual power supply redundancy, non-polarity and anti-reverse connection
Model II| • Voltage range without using PoE function: 12~48VDC;
• Rated voltage: 48VDC;
• Maximum voltage range: 44VDC-55VDC;
Support dual power supply redundancy, anti-reverse connection
Access terminal block| 6-pin 5.08mm pitch terminal blocks, power supply occupies 4 pins
Power Consumption|
Model I| No-load: 3.74W@48VDC
Full-load: 9.6W@48VDC
Model II| No-load: 4.03W@48VDC
Full-load: <130W@48VDC
Working Environment|
Working temperature| -40 ~75 ℃
Storage temperature| -40 ~85 ℃
Working humidity| 5% ~95% (no condensation)
Protection grade| IP40 (metal shell)

3onedata Co., Ltd.
Address: 3/B, Zone 1, Baiwangxin High Technology
Industrial Park, Xili, Nanshan District, Shenzhen
Website: www.3onedata.com
Tel: +86 075526702688
Fax: +86 075526703485

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

3onedata User Manuals

Related Manuals