3onedata IRT5300L-5T2D-2P12_36 Industrial 4G Wireless Router Installation Guide
- June 26, 2024
- 3onedata
Table of Contents
- Package Checklist
- Product Overview
- Panel Design
- Mounting Dimension
- DIN-Rail Mounting
- Disassembling DIN-Rail
- Power Supply Connection
- Serial Port and IO Ports Connection
- Reset Button Setting
- Mounting SIM Card
- Antenna Connection
- Checking LED Indicator
- Logging in to WEB Interface
- Specification
- Disposal of Waste Electrical and Electronic Equipment (WEEE 2012/19/EU)
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
IRT5300L-5T2D-2P12_36
Industrial 4G Wireless Router
Quick Installation GuideAddress: 3/B, Zone 1,
Baiwangxin High Technology
Industrial Park, Xili, Nanshan District,
3onedata Co., Ltd.
Shenzhen
Website: www.3onedata.com
Tel: +86 0755-26702688
Fax: +86 0755-26703485
Package Checklist
Please check whether the package and accessories are intact while using the
industrial 4G router for the first time.
1 4G router x1 2. DIN-Rail mounting attachment
3. WIFI antenna x2 4. LTE antenna x2
5. Power adapter 6. SIM card ejection pin
7. Certification 8. Warranty card
If any of these items are damaged or lost, please contact our company or
dealers, we will solve it ASAP.
Product Overview
This product is DIN-Rail industrial 4G router. The model:
IRT5300L-5T2D-2P12_36 (1 100M WAN + 4 100M LAN + 1 RS-232/485/422 + 2 WiFi
antennas + 2 LTE antennas)
Panel Design
Top view, bottom view and rear view
Front view and side view
- RESET button
- Terminal block for power supply P1 input
- Terminal block for power supply P2 input
- SIM card slot
- 100M WAN port
- Grounding screw
- DIN-Rail mounting kit
- Power supply indicator (P1-P2)
- Wireless network indicator (WLAN)
- Running indicator (RUN)
- 2.4G WiFi antenna interface (WiFi1) RS
- 232/485/422 serial port
- Serial port indicator (COM)
- IO indicator (IO)
- IO port (Reserved)
- 2.4G WiFi antenna interface (WiFi2) LAN
- port indicator
- 100M LAN port
- LTE main antenna interface (LTE-MAIN)
- 4G LTE indicator
- LTE signal strength indicator
- LTE slave antenna interface (LTE-AUX)
Mounting Dimension
Unit: mm
Notice Before Mounting:
- Don’t place or install the device in area near water or moisture, keep the relative humidity of the device surrounding between 5%~95% without
- Condensation. Before powering on the device, check the power specifications supported by the device to prevent device damage due to overvoltage.
- The device surface temperature is high after running; please don’t directly contact it to avoid scalding.
DIN-Rail Mounting
The product adopts 35mm standard DIN-Rail mounting which is suitable for most industrial scenes, mounting steps as follows:
Step 1
Check whether the DIN-Rail mounting kit that comes with the device is
installed firmly.
Step 2
Insert the bottom of DIN-Rail mounting kit (one side with spring support)
into DIN-Rail, and then insert the top into DIN-Rail.
Tips:
Insert a little to the bottom, lift upward and then insert to the top.
Step 3
Check and confirm the product is firmly installed on DIN-Rail, then
mounting ends.
Disassembling DIN-Rail
Step 1
Power off the device.
Step 2
After lifting the device upward slightly, first shift out the top of DIN-
Rail mounting kit, and then shift out the bottom of DIN-Rail, disassembling
ends.
Notice Before Powering on:
- Power ON operation: First insert the power supply terminal block into the device power supply interface, and then plug the power supply plug and power on.
- Power OFF operation: First, remove the power plug, then remove the wiring section of terminal block. Please pay attention to the above operation sequence.
Power Supply Connection
The device provides 4-pin 5.08mm power supply input terminal blocks, and supports P1 and P2 redundant power supply inputs. It could connect to two external power supply inputs, which can ensure the normal operation of the device when one of the systems fails, thus improving the reliability of network operation. The pin definitions of power supply terminal blocks are shown in the left figure, and the power supply input is 12~36VDC.
Serial Port and IO Ports Connection
This device provides 1 RS-232/485/422 serial port, 1 IO input and output interface (reserved), and the interface type is 2×5-pin 3.81mm pitch terminal blocks. The pin definitions of interface are shown as follows:
PIN | RS-232 | RS-485 | RS-422 | IO (Reserved) |
---|---|---|---|---|
1 | TX | DATA- | T- | — |
2 | RX | — | R- | — |
3 | GND | GND | GND | — |
4 | — | — | — | DI- |
5 | — | — | — | DO- |
6 | — | DATA+ | T+ | — |
7 | — | — | R+ | — |
8 | GND | GND | GND | — |
9 | — | — | — | DI+ |
10 | — | — | — | DO+ |
Reset Button Setting
This device provides 1 RESET button, press the button for 1-2s then release it to reboot the device; press the button for 5s then release it to restore factory defaults.
Mounting SIM Card
This device provides 2 SIM slots. It would pop up after you insert a retrieve
card pin in the little hole beside the SIM slot, and then you should put the
Micro SIM card in the slot correctly and insert the slot back in the router.
Notice:
If the SIM card needs to be changed, the device should be power off first in
case of damaging the card.
Antenna Connection
The device provides 2 WIFI antennas, the antenna specifications are shown below:
Type | P/N | Gain (dBi) | Quantity (pcs) |
---|---|---|---|
4G antenna | 300504004 | 3 | 2 |
2.4G wireless | 8 | -0.8 | 2 |
Checking LED Indicator
The device provides LED indicators to monitor its operating status, which has simplified the overall troubleshooting process. The function of each LED is described in the table below:
LED | Indicate | Description |
---|---|---|
RUN | ON | The device is powered on or the device is abnormal. |
Blinking | The device is running normally | |
OFF | The device is powered off or the device is abnormal. | |
WLAN | ON | Wireless WiFi network is enabled |
Blinking | Wireless WiFi network status is in an active | |
OFF | Wireless WiFi network is running abnormally or turned off | |
P1-P2 | ON | Power supply P1/P2 is connected nd running normally |
OFF | Power supply P1/P2 is disconnected or running abnormally | |
4G | Blinking | LTE module is operating normally |
OFF | LTE module isn’t operating | |
All indicators are out. It means the LTE signal of the opposite end is |
weak or no signal.
| One indicator is on. It means the LTE signal of the opposite end is weak
| Two indicators are on. It means the LTE signal of the opposite end is normal
| All indicators are on. It means the LTE signal of the opposite end is strong
COM| Blinking| The serial port has data being transmitted
OFF| No serial port connection or no data transfer
IO| —| Reserved
1-4| ON| LAN port has established valid network connection
Blinking| LAN port is in network active status
OFF| LAN port hasn’t established a valid network connection
WAN (Green)| ON| WAN port has established valid network connection
Blinking| WAN port is in network active status
OFF| WAN port hasn’t established valid network connection
Logging in to WEB Interface
This device supports WEB management and configuration. Computer can access LAN
port of the device via Ethernet interface. The way of logging in to device’s
configuration interface via IE browser is shown as below:
Step 1 Configure the IP addresses of computer and the device’s LAN port to the
same network segment, and the network between them can be mutually accessed
Step 2 Enter device’s IP address in the address bar of the computer browser.
http://192.168.1.254/
Step 3 Enter the device’s username and password in the login window below.
Step 4
Click the “Login” button to log in to the WEB interface of the device.
Note:
- The default IP address of the device’s LAN port is “192.168.1.254”.
- The default user name and password of the device are “admin”.
- If the user name or password is lost, user can restore it to factory settings via restoring factory setting button; all modified configurations will be cleared after restoring to factory settings, so please backup configuration file in advance.
- Please refer to user manual for specific configuration method of logging in to WEB interface and other configurations about network management function.
Specification
Panel
WAN port| 1 10/100Base-T(X) RJ45 port
LAN port| 4 10/100Base-T(X) RJ45 ports
Serial port| RS-232/485/422, with 2×5-pin
3.81mm pitch terminal (occupies 6 pins)
IO port| Reserved
SIM card slot| 2 SIM slots, redundancy backup, support Micro SIM card
Antenna interface| 2 LTE antenna interfaces, SMA-K(Female)
□ Master antenna is used for sending/receiving information
□ Slave antenna is used for receiving information
2 WIFI antenna interfaces, RP-SMA-K(Female)
Indicator| Running indicator, WLAN indicator, power indicator, LTE signal
strength indicator, 4G indicator, LAN/WAN port indicator, COM indicator and IO
indicator
WIFI Transmission Rate
802.11n| 6.5~300Mbps
802.11b| 11/5.5/2/1Mbps
802.11g| 54/48/36/24/18/12/9/6Mbps
WIFI RF
Channel| 2.412GHz~2.4835GHz
RF power output| 20dBm
Modulation scheme| DBPSK, DQPSK, CCK, OFDM, 16-QAM, 64-QAM
WIFI Receiving Sensitivity
802.11n_HT40| -82dBm@MCS0, -64dBm@MCS7
802.11n_HT20| -85dBm@MCS0, -67dBm@MCS7
802.11g| -91dBm@6Mbps, -72dBm@54Mbps
802.11b| -93dBm@1Mbps, -87dBm@11Mbps
WIFI Transmission Power
802.11n_HT40| 20dBm@MCS0, 20dBm@MCS7
802.11n_HT20| 20dBm@MCS0, 20dBm@MCS7
802.11g| 20dBm@6Mbps, 20dBm@54Mbps
802.11b| 23dBm@1Mbps, 20dBm@11Mbps
LTE Operating Frequency Band
Chinese version| □ TDD-LTE: Band 38/39/40/41
□ FDD-LTE: Band 1/3/5/7/8/20
□ WCDMA: Band 1/5/8
□ TD-SCDMA: Band 34/39
□ EVDO/CDMA1X: BC0
□ GSM: Band 3/8
European & African & Middle East version
Note:
This version can be used in Southeast Asia in most cases.| □ TDD-LTE: Band
38/40/41
□ FDD-LTE: Band 1/3/7/8/20/28A
□ WCDMA: Band 1/8
□ GSM/EDGE: Band 3/8
North American version| □ FDD-LTE: Band 2/4/5/12/13/14/66/71
□ WCDMA: Band 2/4/5
Latin American & Australian & New Zealand version| □ TDD-LTE: Band 40
□ FDD-LTE: Band 1/2/3/4/5/7/8/28
□ WCDMA: Band 1/2/5/8
□ GSM/EDGE: Band 2/3/5/8
Global version| □ TDD-LTE: Band 34/38/39/40/41
□ FDD-LTE: Band 1/2//3/4/5/7/8/12/13/18/19/205/26/28/66
□ WCDMA: Band 1/2/4/5/6/8/19
□ GSM/EDGE: 850/900/1800/1900 MHz
LTE Bandwidth (Downstream, Upstream)
TDD-LTE| Rel 9 Cat4 TDD-LTE
112Mbps/30Mbps
FDD-LTE| Rel 9 Cat4 FDD-LTE
150Mbps/50Mbps
DC-HSPA+| 42Mbps/5.76Mbps
HSPA+| 21Mbps/5.76Mbps
UMTS| 384kbps/384kbps
EVDO RevA| 3.1Mbps/1.8Mbps
EVDO Rev0| 2.4Mbps/153.6kbps
TD-HSPA| 4.2Mbps/2.2Mbps
TD-SCDMA| 2.8Mbps/2.2Mbps
CDMA 1x| 153.6kbps/153.6kbps
EDGE| 236.8kbps/236.8kbps
GPRS| 85.6kbps/85.6kbps
LTE Sensitivity
GSM| <-108dBm
WCDMA| <-109dBm
TD-SCDMA| <-108dBm
TDD-LTE| □ Band38/39/40: <-100dBm @5MHz BW
□ Band41: <-98dBm @5MHz BW
FDD-LTE| □ Band1: <-100dBm @5MHzBW
□ Band3/8: <-97dBm @5MHzBW
□ Band5: <-98dBm @5MHzBW
CDMA| <-108dBm
EVDO| <-108dBm
Maximum Transmission Power of LTE
LTE-FDD/TDD| 23±2dBm
WCDMA| 24+1/-3dBm
TD-SCDMA| 24+1/-3dBm
EVDO/CDMA 1X| 24±1dBm
GSM850/900| 33±2dBm
GSM1800/1900| 30±2dBm
Power Supply
Input power supply| 12~36VDC dual input, dual power supply redundancy, non-
polarity
Access terminal block| 4-pin 5.08mm pitch terminal blocks
Power Consumption
No-load| 2.4W@24VDC
Full-load| 8.1W@24VDC (high temperature)
Working Environment
Working temperature| -40~75
Storage temperature| ℃ -40〜85℃
Working humidity| 5%〜95% (no condensation)
Protection grade| IP40 (metal shell)
Disposal of Waste Electrical and Electronic Equipment (WEEE 2012/19/EU)
(Applicable in the EU-member states)
The crossed-out wheeled bin symbol on the equipment or its packaging indicates
that the product, at the end of its service life, shall not be mixed with
unsorted municipal waste but should be collected separately, in accordance
with local laws and regulations.
A proper separate collection of end-of-life equipment for the subsequent
recycling, treatment and environmentally compatible disposal, will help
prevent potential damage to the environment and human health, facilitating the
reuse, recycling and/or recovery of its component materials. Private users
should contact their vendor or municipal waste management service and ask for
disposal information. Professional users should contact their suppliers and
check the terms of their selling agreement. This product must not be disposed
of with other commercial waste.
Users’ cooperation in the correct disposal of this product will contribute to
saving valuable resources and protecting the environment.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>