Netac OS01 Ture Wireless Open Earphone User Manual
- June 2, 2024
- Netac
Table of Contents
OS01 Ture Wireless Open Earphone
User Manual
0s01
Ture Wireless Open Earphones
Please tears off the insulation film on the earphones
Overview
Power on/off
Auto power on: Take out the earphones, and the earphones will power on
automatically and enter pairing mode, waiting to connect to the phone.
Manual power on: If the earphones are not in the charging case and are
off, press and hold both earphones for 3s to power them on.
Auto power off:
- Put the left and right earphones into the charging case, and close the charging case, it will automatically power off and charge.
- The earphones will automatically power off when it is not connected to the device for Smins. Manual power off: If the earphones are on and connected to each other, press and hold either earphones for 5s to power them off.
Pairing mode
- Take the earphones out of the charging case, when successfully connected, the main headset will flash white and the secondary headset light will go out.
- The earphones in the pairing mode, select Netac OSO1 for pairing in the mobile BT menu.
- After successful connection, there is a reminder.
Music
Play/Pause: Click the touch zone while playing.
Previous song: Double-click the left earphones touch zone.
Next song: Double-click the right earphones touch zone.
Volume
Volume up: Triple click the left earphones touch zone.
Volume down: Triple click the right earphones touch zone.
Call
Answer: Double-click the touch zone when an incoming call comes in.
Reject: Long press the touch zone for 2s during an incoming call.
Hang up: Double-click the touch zone during a call.
Active the voice assistance
Press and hold the left ear touch zone for 2s to wake up/exit the voice
assistant.
Charge
- Charge the charging case through the charging cable, the charging case indicator light is always on when charging is complete.
- The earphones are put into the charging case and charged auto-matically, the earphones indicator light is off when charging is complete.
| Charge the earphones | White light on |
|---|---|
| Earphones fully charged | White light off |
| Charge the case | Blinks light |
| Case fully charged | Solid light |
Specification
- Model: 0501
- BT version: 5.4
- Earphone weight: 8.6g (Single)
- Earphone size: 46.1*44.5″14.2mm
- Earphone battery: 3.7V/2*50mAh
- Charging case weight: 57g
- Charging case size: 109.8*54.8k27.5mm
- Charging case battery: 3.7V/600mAh
- Earphones charging time: About 1.5H
- Music playtime: About 8H (Mid-range)
- BT distance: 10M
- Frequency: 2.402GHz-2.48GHz
- Speaker unit: 014.2MM/220hm
- Input: DC 5V/500mA
- Charging case to earphones charging times: 3
- Support BT Protocol: a2dp avctp\ avdtp\ avrcp hfp\ spp smp\ att \ gap\ gatt\ rfcomm \sdp \I2cap
http://weixin.qq.com/r/bxFJUTfEx2q4rXMy90R9
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.