Netac LK95A True Wireless ANC Earbuds User Guide

Netac LK95A True Wireless ANC Earbuds User Guide

Product profile

1. Touch zone
2. Ear cup
3. Mic
4. Indicator light of earphones zone
5. Indicator light of charge case zone
6. Mic
7. Charge contact
8. Button
9. Type-C port

Power on/off

Automatic Power On: Take out the earphones, and the earphones will power on automatically and enter pairing mode, waiting to connect to the phone.

Manual Power On: If the earph ones are not in the charging case and are off, press and hold both earphones for 3 seconds to power them on.

Automatic Power Off: Place both earphones into the charging case, close the charging case lid, and they will automatically power off while charging.

Manual Power Off: If the earphones are on and connected to each other, press and hold either earphone for 5 seconds to power them off.

Pairing and connection

1. Take out the earphones from the charging case.
2. Turn on the BT on your phone.
3. Locate the earphones’ BT named “Netac LK9SA”.
4. Click to connect, and once successfully connected, you will hear a voice prompt

Note: lf existing paired device information is available, their phones will automa1icallyreconnecttothedevicewithin2-4seconds;lfnotconnectedto any device, the earphones will automatedly power off after 3 min,.,tu of standby.

Calling

Music

Volume Control

Activate Voice Assistant Function

Tap the multi-function touch zone four times to wake up the voice assistant.

Manual Pairing with Mobile Phone

Double-click the right earphone to manually pair.

Manual Pairing with Mobile Phone

Noise Reduction Mode: Press and hold either earphones for 3 seconds to switch from Transparency Mode to Noise Reduction Mode.

Transparency Mode: Press and hold either earphones for 3 seconds to switch from Noi se Reduction Mode to Transparency Mode.

By default, the mobile phone has Transparency and Noise Reduction turned off. Press and hold either earphones for 3 seconds to cycle through Transparency Mode, Noise Reduction Mode, and Noise Reduction Off.

Earphone/Charging Case Indicator Lights

Specification

• Model: LK95A
• BT Version: V5.3+EDR
• Earphone Weight: – 4g (each)
• Earphone Dimensions: 20″26″8mm
• Earphone Battery Capacity: 30mAh
• Charging Time: – 80minutes
• Charging case Weight: – 37g
• Charging case Dimensions: srsr23mm
• Charging case Battery Capacity: 400mAh
• ANC Depth: –30dB
• Supported Protocols: A2DP 1.3.2/ AVRCP 1.6.2 /AVDTP / AVCTP / HFP
• Frequency Response Range: 20Hz-20kHz
• Power Input: DC 5V/300mA
• BT Range: 10m

http://weixin.qq.com/r/bxFJUTfEx2q4rXMy90R9

Beijing Netac Innovation Technology Development co.,Ltd.
Location: Building, Phase ll, Nord Center, Fengtai District, Beijing
Tel: 400-105-S505 {CN)
Web:www.netac.com

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protectionagainst harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RF Exposure Information The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>