Netac LK95 True Wireless Earphones Instruction Manual
- June 16, 2024
- Netac
Table of Contents
LK95
True Wireless Earphones
Product profile
1: Touch zone
4: Indicator light of earphones zone
7: Charge contact| 2: Ear cup
5: Indicator light of charge case zone
8: Button| 3: Mic
6: Mic
9: Type-C port
---|---|---
Power on/off
Automatic Power On: Take out the earphones, and the earphones will power
on automatically and enter pairing mode, waiting to connect to the phone.
Manual Power On: If the earphones are not in the charging case and are
off, press and hold both earphones for 3 seconds to power them on.
Automatic Power Off: Place both earphones into the charging case, close
the charging case lid, and they will automatically power off while charging.
Manual Power Off: If the earphones are on and connected to each other,
press and hold either earphone for 5 seconds to power them off.
Pairing and connection
-
Take out the earphones from the charging case.
-
Turn on the BT on your phone.
-
Locate the earphones’ BT named “Netac LK95”.
-
Click to connect, and once successfully connected, you will hear a voice prompt.
Note: If existing paired device information is available, the earphones will automatically reconnect to the device within 2-4 seconds; If not connected to any device, the earphones will automatically power off after 3 minutes of standby.
Calling
| Answer: Click the multi-function touch zone once when there is an
incoming call.
---|---
| Reject: Press and hold the multi-function touch zone for 1.5 seconds.
| End: Click the multi-function touch zone once during a call.
| Answer a Third-Party Call: Click the multi-function touch zone once to
end the current call and answer the incoming call.
Music
| Pause/Play: Click the multi-function touch zone once during playback.
---|---
| Previous Song: Double-click the multi-function touch zone on the left
earphone during playback.
| Next song: Double-click the multi-function touch zone on the right
earphone during playback.
Volume Control
| Click three times on the left earphone to increase the volume.
---|---
| Click three times on the right earphone to decrease the volume.
Activate Voice Assistant Function
(requires phone support)
Tap the multi-function touch zone four times to wake up the voice assistant.
Manual Pairing with Mobile Phone
Double-click the right earphone to manually pair.
Earphone/Charging Case Indicator Lights
| Earphone Status | Indicator Light Status |
|---|---|
| On | Blue light flashes slowly |
| Charging | Red light is on |
| Fully Charged | Off |
| Connected to Phone | Off |
| Charging Case Status | Charging Case Indicator Light Status |
| USB-5V Charging | Display battery level on the screen |
| Charging the Earphones | Display battery level on the screen |
| Low Battery | Display battery level on the screen |
Specification
- Model: LK95
- BT Version: V5.3+EDR
- Earphone Weight: ~4g (each)
- Earphone Dimensions: 20268mm
- Earphone Battery Capacity: 30mAh
- Charging Time: ~80minutes
- Charging Case Weight: ~37g
- Charging Case Dimensions: 525223mm
- Charging Case Battery Capacity: 400mAh
- Supported Protocols: A2DP 1.3.2/ AVRCP 1.6.2 /AVDTP / AVCTP / HFP
- Frequency Response Range: 20Hz-20kHz
- Power Input: DC 5V/300mA
- BT Range: 10m
http://weixin.qq.com/r/bxFJUTfEx2q4rXMy90R9
Beijing Netac Innovation Technology Development Co.,Ltd.
Location: Building 11, Phase Il, Nord Center, Fengtai District, Beijing
Tel: 400-105-5505 (CN)
Web: www.netac.com
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly
approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
RF Exposure Information
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
True Wireless Earbuds
FCCID:2BEBP-LK95
Model:LK95 B
Beijing Netac Innovation Technology Development Co.Ltd
Made in China.