CONNECTS2 CTSFO023.2 Steering Wheel Control Interface for Ford Vehicles User Manual

CONNECTS2 CTSFO023.2 Steering Wheel Control Interface for Ford Vehicles User Manual

FEATURES

• This interface gives you an ignition feed, allowing you to turn on the head unit without turning the vehicle’s ignition on whilst parked.
• Retains Factory Steering Wheel Control Functionality
• Retains Phone Buttons
• Supports Voice Assistant
• Provides Speed Pulse, Park Brake and Reverse Gear outputs

DISCLAIMER
The information provided in this document is subject to change without notice due to manufacturer changes and/or improvements to the product/s. This instruction manual is based on documented data and research. The manufacturer of this product cannot be held responsible for any changes made to the
vehicle by the manufacturer or damages that may occur through the installation of this product in accordance with the steps outlined herein.

PRIOR TO INSTALLATION

Read the manual prior to installation. Technical knowledge is necessary for installation. The place of installation must be free of moisture and away from heat sources. Please ensure that the correct tools are using during the installation to avoid damage to the vehicle or product. Connects2 can not be held responsible for the installation of this product.

WIRING KEY

STEERING WHEEL CONTROL FUNCTIONALITY

The following diagram, though based on careful research, is an example only. Individual steering wheel control configurations may differ.

1. Voice Assistant (*if software update performed)
2. Track – (Short Press) Pick Up (Long Press)
3. Track + (Short Press) Hang Up (Long Press)
4. Volume
5. Volume +
6. Mute 2

*Visit www.connects2.com for more information on how to download the SWC software update.
Note: a reflasher tool is also required (Part No: SWCREFLASHER)

IGNITION SWITCH

With the switch in its “on” position, you can power up your head unit when parked and enjoy its full array of features without turning on the vehicle ignition or engine. Ideal for motorhomes and day vans.

INSTALLATION GUIDE

See wiring diagram on Pg.4 for more information

Before installing the interface, the factory stereo must be removed and disconnected. To do this, please consult the vehicle owner’s manual/handbook or contact a fitting professional.
A stereo connection (patch) lead is also required for the installation of this interface (supplied separately). Please ensure that you have the correct lead before proceeding. For universal patch leads, prepare the wiring loops in accordance with the instruction manual supplied with the product before installation.

1. Connect the 12 Pin connector from the stereo connection (patch) lead to the interface box

2. Connect the opposite end of the stereo connection (patch) lead to the steering wheel control input on the back of the aftermarket stereo
   NOTE: This may be a 3.5mm jack connector or a wired input depending on the brand of aftermarket stereo being fitted. Please consult the aftermarket stereo installation manual for further information on where to make the connection
   ! IMPORTANT: THIS STEP MUST BE COMPLETED BEFORE CONNECTING POWER TO THE INTERFACE. FAILURE TO DO SO MAY RESULT IN A LACK OF FUNCTIONALITY AND THE NEED TO REINSTALL THE PRODUCT

3. Connect the 14 Pin connector from the supplied wiring loom to the interface box

4. Connect the power/speaker ISO connector from the interface to the power/speaker ISO connector from the aftermarket stereo.
   NOTE: For aftermarket stereos which do not have an ISO connector, please see “Wiring Key” on Pg.2 for information on which wires to connect. Some interfaces may also have additional flying’ wires which can be connected to the vehicle to support various features ie. parking brake trigger, reverse gear and speed pulse. Details of these can be found underAdditional Connections’.

5. Connect the 32 pin vehicle specific connector on the supplied harness to the connectors from the vehicle. Please refer to wiring diagram on Pg.4 for more information.

6. Test stereo and steering wheel control functionality for correct operation before reassembling the vehicle dashboard. If steering wheel control functions are unresponsive, please uninstall the interface and wiring and reinstall carefully in accordance with the above steps.

For further help, please contact and fill out a support ticket with the full details of your issue at: support.connects2.com/tickets/technical

WIRING DIAGRAM

Vehicle Specific Connector [32 Pin] Connect to corresponding connector from vehicle

References

• Connects2 - Vehicle Integration

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>