Connects2 CTSTY019.2 Steering Wheel Control Interface User Manual
- June 3, 2024
- Connects2
Table of Contents
Connects2 CTSTY019.2 Steering Wheel Control Interface
Left to Right:
- Additional Flying Wires
- Vehicle Specific Connector (28 Pin)
- Vehicle Specific Connector (24 Pin)
- Vehicle Specific Connector (6 Pin)
- Vehicle Specific Connector (10 Pin)
- ISO Power/Speaker Connector
- Yellow 360 Camera RCA
- Red & White Aux RCA
- Interface Box
- OEM USB Retention Connector (not pictured)
APPLICATION
- Toyota Highlander 2018 – 2019
- Toyota Land Cruiser Prado 2014 – 2019
- Toyota RAV4 2016 – 2018
For amplified vehicles, does not support fade. This product can be used for both left & right hand drive vehicles. The images in this instruction are representative of left hand drive vehicles.
FEATURE
- Retains Factory Steering Wheel Control Functionality
- Retains Factory Phone Button Functionality
- Retains Amplified System
- Retains 360 Panoramic Camera
- Provides Outputs for Park Brake, Speed Pulse & Reverse Gear
- Software Updatable (contact supplier for more information)
PRODUCT INFORMATION
CTSTY019.2
The CTSTY019.2 is a CAN Bus steering wheel control interface for select Toyota
vehicles. This interface aids in the retention of crucial steering wheel
controls as well as access and control of the Toyota’s 360 Panoramic Camera
functions. Please note: the 360 camera language must be set to the appropriate
format before modification. The interface and new head unit will default to
English if not set up beforehand.
WIRING KEY
IN ISO CONNECTOR
- Purple Right Rear Speaker +
- Purple/Black Right Rear Speaker –
- Green Left Rear Speaker +
- Green/Black Left Rear Speaker –
- Grey Right Front Speaker +
- Grey/Black Right Front Speaker –
- White Left Front Speaker +
- White/Black Left Front Speaker –
- Yellow Permanent 12V
- Black Ground
- Red Ignition 12V
- Orange Illumination
ADDITIONAL CONNECTIONS
- Pink Speed Pulse
- Green Park Brake
- Purple Reverse
- Red/White RCA AUX Audio
- Yellow RCA 360 Camera
STEERING WHEEL CONTROL FUNCTIONALITY
The following diagram, though based on careful research, is an example only. Individual steering wheel control configurations may differ.
Original Function
- Volume Up
- Volume Down
- Arrow Left
- Arrow Right
- Track Up & Down
- Speech
- Back
- Pick Up
- Mode
- 360 View
New Function
- Volume Up (Toggle Lower Left Menu Preset*)
- Volume Down (Toggle Upper Left Menu Preset*)
- Arrow (Toggle Middle Menu Preset*)
- Arrow (Toggle Lower Right Menu Preset*)
- Track Up & Down
- Speech
- Back
- Pick Up (Toggle Upper Right Menu Preset*)
- Enter & Exit 360 Panoramic State (Re-assign Buttons (Hold)*)
- Toggle 360 View
These actions only work when camera view is active & when the buttons have been re-assigned (9.) Menu functionality is dependant on original vehicle spec. The infographic shown above is a representative guide only. Refer to owners manual for full list of options.
PRIOR TO INSTALLATION
Read the manual prior to installation. Technical knowledge is necessary for installation. The place of installation must be free of moisture and away from heat sources. Please ensure that the correct tools are used during the installation to avoid damage to the vehicle or product. Connects2 can not be held responsible for the installation of this product.
INSTALLATION GUIDE
Before installing the interface, the factory stereo must be removed and disconnected. To do this, please consult the vehicle owner’s manual/handbook or contact a fitting professional. A stereo connection (patch) lead is also required for the installation of this interface (supplied seperately). Please ensure that you have the correct lead before proceeding. For universal patch leads, prepare the wiring loops in accordance with the vinstruction manual supplied with the product before installation.
-
Connect the 12 Pin connector from the stereo connection (patch) lead to the interface box. See wiring diagram on Pg.4 for more information
-
Connect the opposite end of the stereo connection (patch) lead to the steering wheel control input on the back of the aftermarket stereo.
NOTE: This may be a 3.5mm jack connector or a wired input depending on the brand of aftermarket stereo being fitted. Please consult the aftermarket stereo installation manual for further information on where to make the connection. -
Connect the 20 Pin connector from the supplied wiring loom to the interface box.
-
Connect the power/speaker ISO connector to the power/speaker ISO connector at the rear of the aftermarket stereo.
NOTE: For aftermarket stereos which do not have an ISO connector, please see “Wiring Key” on Pg.2 for information on which wires to connect. Some interfaces may also have additional ‘flying’ wires which can be connected to the vehicle to support various features ie. parking brake trigger, reverse gear and speed pulse. Details of these can be found under ‘Additional Connections’. -
Connect the additional wiring, AUX connectors & Yellow RCA connection to the aftermarket stereo’s wiring harness where required.
-
Connect the vehicle specific power connectors on the supplied harness to the OEM connectors from the vehicle.
-
Test stereo and steering wheel control functionality for correct operation before reassembling the dashboard. If the steering wheel control functions are unresponsive, please uninstall the interface and wiring and reinstall carefully in accordance with the above steps.
360 CAMERA FUNCTIONALITY
Access of the 360 Camera:
When in Park – a short press of the 360 View Button (10.) will showcase the
‘dynamic 360 view’ (Figure 1). In this view, utilise the button presets to
alter the various viewing angles*. Another short press of the 360 View Button
(10.) will exit to the main menu.
When in reverse – upon engaging reverse gear, the ‘rear view & panoramic
view” will populate on the display (Figure 2). A short press of the 360 View
Button (10.) will switch this view to ‘rear view’ (Figure 3). Disengagement of
the reverse gear will exit the 360 camera mode.
When in Drive: Shifting from Reverse to Drive, the camera will switch to
‘front & panoramic view’ (Figure 4). A short press of the 360 View Button
(10.) will switch the display to the ‘front left / front right view’ (Figure
5). A following short press of the 360 View Button will exit to the main menu.
Functionality of the camera is dependent on access to ‘re-assigned buttons’.
This is achievable after holding Mode for approx 8 seconds. Layout of the menu
systems will differ dependent on left & right-hand vehicles.
360 Camera Button Settings:
Long press the Mode button (9.) for more than 8 seconds will ‘re-assign’ the
steering wheel controls, this meaning you can utilise the controls for various
functions whilst “Panoramic View” is enabled. Herein, you are able to toggle
the look of various features such as the colour/layout of parking lines & 360
layout.
‘AUTO’ Functionality:
In addition to screen switching by operating the camera switch (10.),
automatic display mode is available (see figure 4/5). In this mode, the screen
is switched automatically in response to vehicle speed. The monitor will
automatically display images in the following situation: 1) When the shift
lever is shifted to “N” or “D” position. 2) When the vehicle speed is reduced
to approximately 10mph (18km/h).
If no operation is perfomed after roughly 15-20 secs, the camera mode will close itself.
Language settings:
The language is completely controlled by the original vehicle system. If a
desired language is needed, this needs to be done prior to installation of the
new head unit as this interface does not support language setting
functionality. The interface will default the language to English if not
already set.
WIRING DIAGRAM
DISCLAIMER
The information provided in this document is subject to change without notice due to manufacturer changes and/or improvements to the product/s. This instruction manual is based on documented data and research. The manufacturer of this product cannot be held responsible for any changes made to the vehicle by the manufacturer or damages that may occur through the installation of this product in accordance with the steps outlined herein.
For further help, please contact and fill out a support ticket with the full
details of your issue at:
support.connects2.com/tickets/technical
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>