FleetPoint OBDII 1 OBD GPS Tracker User Manual

FleetPoint OBDII 1 OBD GPS Tracker

Overview

Appearance

LED indications

1. power indicator(red)****
   Slow flashing| full charge/working normally
   ---|---
   Solid red| charging

No ligh

| ower off/low battery /internal fault/sleep mode
2. GSM indicator(green)**
Quick flashing| GSM initialing
---|---
Slow flashing| receive GS             al normally
Solid green| in communication With phones link up
No light| no GSM signal or no SIM card
3. GPS indicator(blue)**
| archin G          signal
---|---
Solid blue| positioned
No I ht| not working/sleep m  e

SIM card installation

Open the lid

please insert the pry piece in the box to the shell on either side of the open lid hole according to the direction as the picture shows, the upper lid will off the lower lid. Next insert the other side of the open lid hole, and press and gently pry open follow the direction shown in the picture. If this is still not open, repeatedly push both sides to separate the upper and lower lid. After the lid is removed, install the SIM card follow the installation method
(please see 3.3 SIM card installation).

Close the lid

When closing the lid, be sure that the positioning semi-circular hole is in the same direction as the semi-cylinder of the upper lid.close the lid violently in the wrong direction will cause damage to the equipment.

SIM card installation

Please purchase the right SIM card.

Install SIM card

Insert the SIM card in correct direction. Push the card cover to the LOCK direction and make sure to lock it.

NOTE

1. When the SIM card is inserted, device will use the backup battery to power on. If the charge of the internal battery is low, please insert the device to the OBD interface of the car to take electricity.
2. Terminal SIM card should be inserted in the correct direction. SIM card should have GPRS service. If SIM PIN required, please turn off the SIM PIN function. Please ensure that the terminal SIM card charges sufficient.

Boot up/power off

1. Boot up
   After insert the SIM card, the device will power on by using the backup battery. When the device is inserted into the OBD interface, the internal battery will be charging.

2. Power off
   After unplugging the device from the OBD interface, then removing the lid and taking off the SIM card, the device will shut down.

Functions

The following features can be configured through the terminal platform or APP provided by the dealer.

SOS number

1. Add SOS number Via SMS command
   Send SMS command: SOS, A,number1 ,number2,number3 #(A means add number). You could set 3 SOS numbers in maximum. If set successfully, the terminal will reply “ok”. e.g. SOS,A, 13510 …. 60,135116 …. 6,136126 …. 8# (set all 3 SOS numbers)
   SOS,A, 13510 …. 60# (set the first SOS number)
   SOS,A, , 135116 …. 6# (set the second SOS number)
   SOS,A, , ,136126 …. 8# (set the third SOS number)

2. Delete SOS Numbers
   Send SMS command: SOS, D, 1,2,3# (D means delete SOS number) e.g. SOS, D, 1 # means delete the first number  SOS, D,3# means delete the third number If you do not know the sequence number, you can also delete the number by SMS command like this: SOS, D, number# e.g. SOS, D, 13527852360# means delete this SOS number directly. It will reply “OK” if the number is deleted successfully.

3. Add SOS numbers via platform
   You can set SOS number via the platform after activating the terminal.

Plug out alarm

When the device unplugged from the car, the device will send “unplug alert” message to the platform or SOS numbers

Power cut-off alert

When the electricity supply of device is cut off, it will activate power cut- off alarm. Then the device will send “power cut-off alert” message to the platform or SOS numbers.

Low battery alert

If the device uses backup battery to work, the device will send low battery alert to platform when battery is low.

Geo-fence alert

After setting the fence area on the platform and selecting the trigger conditions of the alarm, the device will send correspong­ding in and out alert to the platform according to the trigger conditions when the device enters and exits the gee-fence.

Overspeed alert

The car speed threshold can be set by platform or SMS. When vehicle speed over the setting threshold, the Overspeed alert will be triggered.
NOTE:
Off by default, on / off on the specified platform or phone client.

Platform operation

Get registered on the designated service platform/ APP by authorized dealer, then you can start the tracking service and settings.

Troubleshooting

If you are having trouble with your device, try these troubleshoot­ing procedures before contacting a service professional.

Warranty instructions and service

1. The warranty is valid only when the warranty card is properly completed, and upon presentation of the proof of purchase consisting of original invoice indicating the date of purchase, model and serial No. of the product. We reserve the right to refuse warranty if this information has been removed or changed after the original purchase of the product from the dealer.
2. Our obligations are limited to repair of the defect or replacement the defective part or at its discretion replacement of the product itself. Warranty instructions and service
3. Warranty repairs must be carried out by our Authorized Service Centre. Warranty cover will be void, even if a repair has been attempted by any unauthorized service center.
4. Repair or replacement under the terms of this warranty does not provide right to extension or renewal of the warranty period.
5. The warranty is not applicable to cases other than defects in material, design and workmanship.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>