TONMiND IP Speaker User Manual
- June 3, 2024
- TONMIND
Table of Contents
TONMiND IP Speaker
Overview
SIP-Sxxx series is IP based paging speaker. They have different shape,
materials and design which can be easy installed in indoor and outdoor
environment. Tonmind IP speakers are well compatible with SIP & ONVIF protocol
that can be used in VoIP and security field. Up to 10 RTP multicast address
enable to arrange different paging solutions. Alarm in and HTTP URL are able
to combine with alarm system. Pre-recorded message and schedule broadcasting
to meet various paging demands. The 48K OPUS Audio Codec enables excellent
sound quality to make announcement, play background music, security alarm in
school, factory and hospital, etc.
Web Configuration
Web configuration includes complete function setting . When the device and
your computer are connected to a same network, please open a browser and type
in http://192.168.5.200, then log in with defaulted username and password as
below. Username: admin
Password: tm1234
Status
You can check out firmware version, free space and two SIP accounts status of IP speaker, also can locate the current network information here, like MAC, IP address and gateway etc.
Basic
Date/ Time
There are two update modes for time：NTP/ local time, choose one and set the
time zones, NTP sever and interval can choose default setting, then save the
configuration.
Network
When you choose DHCP and save it, IP address will be created automatically by
a DHCP server, then you need to login again with the new IP address on
browser: 192.168.5.XXX.
Status IP address: it is a default IP and will not be changed as following
.
ONVIF
Select Enable ONVIF, then the device be searched by ONVIF VMS. Default user
name: admin, password:tm1234.
SIP Account
Each speaker has two SIP accounts, put SIP extension messages into the blanks and save the configuration, then you can check if it registers successfully or not on status.
| Expire Time | Set the expire time of registered account information |
|---|---|
| Ringing Tone | 5 system ringtones and 10 users upload media files |
| Auto Answer | answer immediately and answer delay when a calling incomes |
| Incoming Notify | Put an input URL, when a incoming call ringing, URL take |
effect
Answer Notify| Put an input URL, when a incoming call answered, URL take
effect
Audio
- Out volume : adjust mic and output volume at 0-100.
- Jitter buffer : to make the audio more stable.
- Amp auto off : It’s set defaulted as ON, then there is no noise when not broadcasting. Code setting: four audio codes to compatible with major audio sources.
Media File
There are five system ringtones, and you can upload 10 media files as customers’ demands: music, announcement, bells, etc.
Alarm
Alarm In
enable the alarm, select a file and cycle mode, then save setting. and the connect alarm device to the alarm input port in IP speaker.( currently only SIP-S21T horn speaker support)
Http URL
User can control the alarm by HTTP URL:
- Enable the selection;
- Open any browser you have in computer;
- Put the URL as the following examples, enter it.
Schedule
This function is widely use in school, factory and office projects. Making a
regular bell, announcement and alarm.
Enable the schedule, you can name the schedule. then setting it step by step
.
RTP Multicast
There are 10 RTP addresses can be received for each device, please note that: port numbers do not use continuous numbers when setting the same RTP addresses. Use discontinuous numbers. eg:
- 239.255.1.2:8000，239.255.0.1:8001，239.255.0.1:8002（×）
- 239.255.0.1:8000，239.255.0.1:8002，239.255.0.1:8004 (√)
- Multicast address range: 224.0.0.0-239.255.255.
- Ports range: 1024-65536
- Use IP Tool, Audio manager and PA System to make RTP multicast.
Firewall
This function is use to protect your network safety. You can edit the firewall
automatic defence rules as you need as follows.
System
Upgrade
When reboot and reset the system, system will turn to original setting, and
you need to re-login the web page.
How to upgrade IP Speaker firmware version in web interface?
- Select the latest version firmware CS20-xxx-bin.
- Click upgrade to refresh, it would require about 20s.
- Re-login the web interface, latest version has upgraded.
Security
Set a new user name and password as you need, save the configuration and
restart login.
IPTool Configuration
Apart from Web configuration, IPTool is the other option that configure quickly basic information such as SIP account setting, volume setting, RTP Multicast setting, upgrade. Please follow below steps.
- Download IPTool in https://www.tonmind.com/category/downloads/5
- Enter IPTool, scan local network, the device will appear and then start setting.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>