Weller T0051616699 Pyropen Junior Mini Butane Gas Soldering Iron Instruction Manual
- May 15, 2024
- Weller
Table of Contents
- T0051616699 Pyropen Junior Mini Butane Gas Soldering Iron
- GAS FILLING (T005 16 160 99)
- HOW TO USE SOLDERING TIP AND HEAT TIP
- HOW TO USE THE TOOL AS TORCH
- CAUTION
- VARIOUS TYPES OF INTERCHANGABLE TIPS
- TROUBLE SHOOTING
- HOW TO USE THE IRON HOLDER
- Specifications
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Pyropen Jr.
Operating Insttructions
T0051616699 Pyropen Junior Mini Butane Gas Soldering Iron
GAS FILLING (T005 16 160 99)
- Use original Weller Pyropen gas.
- Be sure that the switch ring is in “OFF“ position.
- Hold the Pyropen Jr. handle with tip pointing downward, refill nozzel in upright position. Insert nozzel of gas container and press down.
- As soon as the Pyropen Jr. is filed, gas will flow over.
- Hold the tool firmly and see the window to read LP gas volume inside.
HOW TO USE SOLDERING TIP AND HEAT TIP
- Push up switch ring marked (A) and turn to right. Gas will start to flow. Set mark °between “ON“-1.
- Push knurled cap marked (B) fully upward. Be sure not to cover air takein hole (marked C), as flame will leak out ignition vent and catalyst will not react (see illustration below).
- While holding the knurled cap upward, ignite ignition vent by using a match or lighter. When the inside of ignition vent turns red, release the knurled ring. It will return to its original position and generate heat.
- Adjust tip temperature by moving the switch ring (1-3).
- To turn off, slide the switch ring to “OFF“ position.
- For any job with hot air replace soldering tip by hot blow tip.
HOW TO USE THE TOOL AS TORCH
-
Loosen knurled cap to remove tip and tip housing.
-
Push up switch ring marked (A) and turn to right. Gas will start to flow.
Set mark °between “ON“-1. -
Ignite by using a match or lighter as shown in above illustraion.
-
Adjust amount of flame by switch ring (1-3).
-
To turn off, slide the switch ring to “OFF“ position.
CAUTION
- Check tools for damage before use.
- If damage is found, the device must not be used and the tank must not be refilled.
- Repairs are only to be performed by authorised specialist personnel.
- Do not fill gas or store near open flame, heater, furnace or combustible materials. Do not store at places under direct sunshine or any places that will exceed 40°C.
- Do not store the Pyropen Jr. in the dash-board of a car.
- Keep out of reach of infants.
- When not in use, be sure that switch ring is at “OFF“ position.
- When starting operation in winter or at cold places (at about or lower), it may be hard to ignite the gas. This is because of butane gas nature. Hold handle in warm hand until the gas will start to evaparate. Be sure, however, not to try to warm up at open flame or in hot water.
- The catalyser is delicate and easily break.
- Do not use alcohol to clean the Pyropen Jr.
- When using a soldering tip or a hot blow tip, hot air comes out from the exhaust hole in the tip. Be sure to keep clear from the hole to avoid burns.
VARIOUS TYPES OF INTERCHANGABLE TIPS
| Description | Modell | Width | Order No. |
|---|---|---|---|
| Tapered needle | 71-01-01 | Ø 1,0 mm | T0051616599 (standard) |
| Chisel | 71-01-02 | 2,0 mm | T0051616699 |
| Chisel | 71-01-04 | 5,0 mm | T0051616199 |
| Round spade 45° | 71-01-03 | Ø 2,0 mm | T0051616799 |
| Hot air nozzle | 71-01-50 | Ø 1,5 mm | T0051616899 |
| Hot air nozzle | 71-01-52 | Ø 4,7 mm | T0051616999 |
TROUBLE SHOOTING
| Trouble | Possible reason | Correction |
|---|---|---|
| No gas flow | Empty gas container | Refill |
| Torch flame has no power | Gas container probably almost empty | Refill |
| Impossible to ignite gas | Gas pressure is too high or too low | Adjust |
correctly Position 1-3
Tip does no heat up| Catalyser is damaged
Insufficient gas power| Replace soldering tip Refill
If your device ceases to function correctly, take it to your nearest authorised customer service centre www.weller-tools.com
HOW TO USE THE IRON HOLDER
Always place the soldering tool in the safety rest while not in use!
Put accessory on any box edge as illustrated (one larger nail of holder comes
outside of box and two nails inside).
Specifications
| Length incl. soldering tip: | 175 mm / 6.88″ |
|---|---|
| Weight incl. gas filling: | 56.4 g / 1.9 oz. |
| Temperature values: | Soldering iron 250° – 450°C / 482° – 852°F |
Hot blow 430°C / 806°F
Burning time per gas filling:| 0.3 hours with gas control lever set at 2.
Gas consumption per hour| 8g
Filling quantity:| 6 cc / 0.34 cu. inch
Subject to technical alterations and amendments!
See the updated operating instructions at www.weller-tools.com
GERMANY
Weller Tools GmbH
Carl-Benz-Straße 2
74354 Besigheim
Tel: +49 (0)7143 580-0| THE NETHERLANDS
Apex Tool Group B. V.
Phileas Foggstraat 16
7821 AK Emmen
Te l : +31 (0) 591 66 75 00
---|---
USA
Apex Tool Group, LLC.
Weller Professional Tools Division
1000 Lufkin Road
Apex, NC 27539
+866-498-0484| CHINA
Apex Tool Group
Room 302A,
NO 177 Bibo Road
Shanghai, 201202
Tel: +86 (21) 60880288
GREAT BRITAIN
Apex Tool Group UK Ltd
Registered in England,
Company Number 14127816
Registered Office:
C/O TMF Group 13th Floor,
One Angel Court, London,
EC2R 7HJ, United Kingdom
info@weller-tools.com
www.weller-tools.com
© 2023, Apex Tool Group, LLC.
Weller is a registered Trademark and registered Design of Apex Tool Group,
LLC.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>