Cloudy Bay Lighting Supply Instruction Manual

INSTALLATION INSTRUCTIONS
PLEASE READ CAREFULLY BEFORE INSTALLING THE FIXTURE
Save these instructions, as you may need them at a later date.

Lighting Supply

Thank you for purchasing CloudyBay Smart LED Lighting Fixtures .
LED RGBCW TUNABLE RECESSED GIMBAL NARROW FLOOD LIGHT

GENERAL: All electrical connections must be in accordance with local and National Electrical Code (N.E.C.) standards. If you are unfamiliar with proper electrical wiring connections, contact and obtain the services of a qualified electrician. Use UL or IEC-approved wire only for input/output connections.
Remove the fixture and mounting components from the box, and make sure that no parts are missing, by referencing the illustration in the illustration instructions.
Turn the power off before installation, inspection, or removal.
Use all necessary precautions while performing this procedure.
Consult a qualified electrician to ensure the correct branch circuit conductor. Min 90°C supply conductors. Properly ground electrical enclosure. IT IS IMPERATIVE THAT
THE OUTLET BOX BE PROPERLY GROUNDED.
**** DO NOT REVERSE THE HOT AND NEUTRAL CONNECTIONS, OTHERWISE, SAFETY WILL BE COMPROMISED. Never Cover the Control box with a metal box or concrete box, which will prevent it from receiving a signal. This Integrated LED Fixture has no lamp/bulb to replace. Contact us through: smart@cloudybaylighting.com

TROUBLESHOOTING

• Check that the line voltage is correct.
• If there is no voltage, then check all connections.
• Check that the junction box is grounded properly.
• If the light kit does not light:
  Check the wire connection between the junction box and the light kit is correct

CLEANING AND MAINTENANCE:

CAUTION: Ensure the fixture temperature is cool enough to touch.
DO NOT clean or perform maintenance while fixture is energized.

• Clean the lens and fixture with a non-abrasive cleaning solution.
• Do not open the fixture to clean LED. Do not touch the LED.
• Do not spray liquid directly on to LED, LED driver, or wiring.

3-Year Limited Warranty

LIMITED WARRANTY: This fixture is warranted to be free from defects in workmanship and material for up to 3-years. Based upon reasonable household usage, when used in accordance with the package and included instructions. If this fixture does not last for the time period guaranteed, the manufacturer will send smart@cloudybaylighting.com you a replacement fixture upon receipt of the returned fixture, register receipt, and proof of purchase. To contact us, please email us to find out how to return the fixture. We are committed to making high-quality products. Returning the fixture will help us monitor and further improve product quality. This replacement is the sole remedy available, and LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED

PACKAGE CONTENTS

Junction box

Light kit integrated with control box

3 Port Quick Connectors

Wire clip USER MANUAL & VOICE CONTROL GUIDE

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

INSTALLATION OVERVIEW

1. Turn off the power at the source

2. Make a hole in the ceiling with a template in the package

3. Carefully remove the knock-out with a screwdriver or punch.

4. Open the connector’s box cover. Feed supply wire into a knockout hole using a connector and make all connections inside the junction box using the EZ connectors (see picture below). Connect the 120V line wire to the black wire. Connect the neutral wire to the white wire. Connect the ground wire with bare cooper wire. Put on the junction box cover.

5. Connect male and female cables, raise the spring evenly and push the light kit into the ceiling hole.

6. Restore power.

7. Follow User Manual and Voice guidelines to set up the product properly. Please contact us first if you have any questions on using our products.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>