Eltako FDG62-230V Wireless DALI Gateway Installation Guide

Eltako FDG62-230V Wireless DALI Gateway

Only skilled electricians may install this electrical equipment otherwise there is the risk of fi re or electric shock!

FEATURES

• Temperature at mounting location: -20°C up to +50°C.
• Storage temperature: -25°C up to +70°C.
• Relative humidity: annual average value <75%.

valid for devices from production week 27/22 (see bottom side of housing)

SPECIFICATIONS

• Wireless DALI Gateway, bidirectional.
• Only 0.5 watt standby loss.
• For installation.
• 49x51mm, 20mm deep.
• The connection terminals are plug-in terminals for conductor cross-sections from 0,2mm² to 2,5mm².
• The convenient tap technology permits the teach-in of up to 32 wireless universal pushbuttons, wireless direction push buttons, wireless central control pushbuttons, motion sensors, and tunable white and intensity double rocker pushbuttons.
• Bidirectional wireless switchable.
• Power supply 230V at terminals N and L. The DALI bus power supply DL-N2-80mA and up to 40 DALI devices are connected to the DALI terminals.
• The gateway FDG62 controls DALI devices with Enocean wireless transmitters.
• Only broadcast commands can be sent. The FGD62 internally saves the dimming value and supplies this value as feedback. The same feedback telegrams are generated as for an FD62NPN.
• Actuators can then be activated by the feedback signals.
• The FDG62 fulls the function of the DALI master.

Installation

After switching on the supply voltage, the complete DALI bus is scanned, the connected lamps are switched on with maximum brightness and dimmed down to minimum brightness, this can take a few seconds. The teaching mode is then automatically active for 2 minutes if the memory content is empty (delivery status) or if the teaching mode was not locked. The readiness for programming is signaled by briefly switching the lamp on and off. If there is no action for 2 minutes, the teaching mode will be ended automatically. This is signaled by the lamp briefly switching on and off.

Typical connection

Teaching-in sensors

• Universal pushbutton: tap briefly 3 times;
• Direction pushbutton: tap briefly 4 times;
• Direction buttons are automatically fully taught-in when tapped. There where is typed, is then for switching on defined, the other side for turning off.
• Central control button: tap briefly 5 times; central control buttons are automatically taught in completely when tapped. Central ON is where you tap, the other side is central OFF.
• White tone and intensity double rocker switch: 6 short taps.
• Wireless motion sensor FB55B, FBH55SB: (EEP:A5-07-01).
• Rotary button and GFVS: (EEP:A5-38-08); When teaching-in, the confirmation tele-grams are switched on and sent automa-tically. The teaching mode is automatically blocked here. After a button has been taught-in, this is confirmed by the lamp briefly switching on and off, the teach-in mode is active for a further 2 minutes.
• To prevent unintentional teach-in, the teach-in mode is automatically blocked 2 minutes after the last teach-in. This is signaled by the lamp briefly switching on and off twice.
• Unencrypted and encrypted sensors can be taught in.

Teach in encrypted sensors

1. Activate teach-in mode if necessary.
2. Activate sensor encryption within 2 minutes.
3. Then teach in the encrypted sensor as described under ‘Teach in sensors’.

With encrypted sensors, use the ‘rolling code’, i.e. the code changes in each telegram, both in the transmitter and in the receiver. If a sensor sends more than 50 telegrams when the actuator is not active, the sensor is no longer recognized by the active actuator and must be taught in again as an ‘encrypted sensor’. It is not necessary to teach in the function again.

Block teach-in mode immediately

Tap an already taught-in radio button (not central control button) 3 times briefly plus 1 time long (>2 seconds). Locking is signaled by briaefly switching the lamp on and off twice.

Unlock teaching mode

Tap an already taught-in radio button (not central control button) 4 times briefly plus 1 time long (>2 seconds). The readiness for programming is signaled by briefly switching the lamp on and off.
Delete memory content completely (restore delivery status):

1. Switch the supply voltage off and on.
2. Tap an already taught-in radio button (not central control button) 8 times briefly plus 1 time long (>2 seconds). Deletion is signaled by briefly switching the lamp on and off.
3. Start again to ‘Teach in wireless push-button’.

Completely delete the memory content without a radio button (restore delivery status):
Switch on the supply voltage, the lamp switches on with maximum brightness and dims to minimum brightness, then switch off the supply voltage. Repeat this a total of 8 times, at the end of the 8th time the lamp turns off and the memory has been cleared. Direction pushbutton: ‘Switch on and dim up’ on one side and ‘Switch off and dim down’ on the other side.
Universal pushbutton: Short control commands switch on/off, permanent control changes the brightness up to the maximum value. An interruption of the control changes the dimming direction.

Central control button

• Central ON: short click switches on with memory value.

• In motion detector mode, you can switch to permanent ON by pressing >3 seconds (acknowledgment by flashing of the lamp). Central OFF: Short click switches off.

• In motion detector mode, you can switch to permanent OFF by pressing >3 seconds (acknowledgment by flashing of the lamp). A short click on the central control button, direction button or universal button ends the stuck mode, i.e. the motion detector is evaluated again.

• Rotary switch: Press or turn to switch on. Turn right to dim up and turn left to dim down. Press to turn off.

• White tone and intensity double rocker switch: The left rocker changes the color temperature, top press cold white and bottom press warm white. The right rocker changes the intensity, brighter at the top and darker at the bottom.

• Children´s room function (universal button or direction button on the switch-on side): When switching on by pressing the button for a longer period of time, after approx. 1 second it is switched on with the lowest brightness and, as long as the button is pressed, it is slowly dimmed up without changing the last saved brightness level.

• Semi-automatic motion detection with taught-in wireless motion sensor FB55B, FBH55SB (factory setting):
  After switching on with a button, an off-delay time of 2 minutes is started, within this time, a follow-up switch is made if there is movement. If no more movement is detected, it switches off automatically after 2 minutes. The actuator then reacts to movement for a further 2 minutes and switches back on automatically if necessary. After the time has elapsed, the button must be used to switch it on again. It can be switched off at any time with a button, movement is then no longer evaluated.

• Fully automatic motion detection with taught-in wireless motion sensor FB55B, FBH55SB:
  If the actuator should also switch on automatically when there is movement, e.g. in rooms without daylight, the jumper in the movement sensor must be switched to ‘active’. If no more movement is detected, it is switched off automatically after the release delay time of 2 minutes has expired. It can be switched on and off at any time with a button, and it is automatically switched on again when there is movement. With control via the GFVS software, light scenes can be set and called up.

• Switch confirmation telegrams on or off:

  1. Switch the supply voltage off and on.
  2. Tap an already taught-in radio button (not central control button) 7 times briefly plus 1 time long (>2 seconds). On is signaled by briefly switching the lamp on and off twice. The lamp briefly switches on and off to signal off.

Manuals and documents in further languages

http://eltako.com/redirect/FDG62-230V

• Frequency 868.3MHz
• Transmit power max. 10 mW

Hereby, Eltako GmbH declares that the radio equipment type FDG62-230V is in com-pliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address: eltako.com
Must be kept for later use!We recommend the housing for operating instructions GBA14. Eltako GmbH
D-70736 Fellbach Technical Support English: +49 711 94350025 technical- support@eltako.de eltako.com
27/2022 Subject to change without notice.

References

• FDG62-230V » Eltako

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>