KEMI MOTO B0810-00101CL Front and Rear Hub Lights Instruction Manual
- June 1, 2024
- KEMI MOTO
Table of Contents
KEMI MOTO B0810-00101CL Front and Rear Hub Lights
Specifications
- SKU: B0810-00101CL
- Front Hub Light Quantity: 2
- Rear Hub Light Quantity: 2
- Screwdriver: 1
- Tapes: 20
- Wire Harness: 1
- Remote Control: 1
- *M48 Screw Quantity:** 6
Product Usage Instructions
- Installation Tips
- Ensure the vehicle is clean and free of debris before installation.
- Follow the installation steps in the specified order for safety and satisfactory installation.
- Step 1: Right Front Tire
- Remove the corresponding hub light brackets 1, 2, 3.
- Step 2: The Right Front Tire Continued
- Remove the tyre, then unscrew screws A, B, and C. Insert them into the corresponding slots A-1, B-2, C-3 (pay attention to the direction of the bracket bending), slightly tighten screws A, B, and C just enough to clamp the bracket without fully tightening them.
- Red wire (positive terminal)
- For power instructions: Lift the driver’s seat, find the original car power supply, and connect the corresponding positive and negative terminals.
- Get the Dedicated App
- Download the app from Google Play or the App Store by scanning the barcode. Location access permission is necessary for the app.
FAQs
- Q: Can I install the hub lights on any type of vehicle?
- A: The hub lights are designed for specific vehicle models. Ensure compatibility before installation.
- Q: How do I troubleshoot if the remote control is not working?
- A: Check the battery in the remote control, ensure it is properly connected to the power supply, and check for any obstructions between the remote and the hub lights.
BEFORE YOU BEGIN
- Please read the instructions carefully and verify that each item is in the list.
- Please retain these installation instructions for further reference and parts ordering information.
IMPORTANT
- Please read the installation instructions carefully before you start.
- If the vehicle is clean and free of other debris, it will be easy to install.
- For your safety and to ensure a satisfactory installation, please complete all the installation steps in the order shown below.
PRODUCT INFORMATION
- L – Front Hub Light x1
- R – Front Hub Light x1
- L – Rear Hub Light x1
- R – Rear Hub Light x1
- Cross/Flat-Head Screwdriver
- Tapes x20
- Wire Harness x1
- Remote Control x1
- M4*8 Screw x6
INSTALLATION TIPS
- STEP 1 Remove the tyre, then unscrew screws A, B, and C.
- STEP 2 Insert them into the corresponding slots A-1, B-2, and C-3 (pay attention to the direction of the bracket bending), slightly tighten screws A, B, and C just enough to clamp the bracket without fully tightening them.
- STEP 3 Insert the outer ring of the R-front hub light ② into the bracket, align the holes with the bracket holes, and lock the removed small hub light screws D back onto the bracket, then tighten screws A, B, and C.
- STEP 4 Finally reinstall the front right tire and tighten the screws.
- STEP 5 Remove the right rear tyre.
- STEP 6 Loosen screw A to rotate out the height of the installation bracket, and remove screws B and C.
- STEP 7 Insert them into the corresponding slots A-1, B-2, and C-3 (pay attention to the direction of the bracket bending), slightly tighten screws A, B, and C just enough to clamp the bracket without fully tightening them.
- STEP 8 Insert the outer ring of the hub light into the bracket, align the holes with the bracket holes, and lock the removed small hub light screws back onto the bracket, then tighten screws A, B, and C.
- STEP 9 Finally reinstall the right rear tire and tighten the screws.
- STEP 10 For power instructions: Lift the driver’s seat, find the original car power supply, and connect the corresponding positive and negative terminals.
REMOTE CONTROL
GET THE DEDICATED APP FOR IT
Download the app in Google Play, or the App store and scan the barcode.
FCC
FCC Caution:
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, under part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used following the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
Suppose this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on. In
that case, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20cm between the radiator & your body
CONTACT
- www.kemimoto.com.
- Designed by Kemimoto Group
- Kemimoto All Rights Reserved, Infringement must be prosecuted.
- SKU: B0810-00101CL
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>