Artillery 472514 Genius Pro 3D Printer Instruction Manual

Artillery 472514 Genius Pro 3D Printer

READ THIS MANUAL COMPLETELY BEFORE

ASSEMBLING AND POWERING UP YOUR PRINTER!

HAZARDS AND WARNINGS
The Artillery Genius Pro 3D Printer has motorized and heated parts. When the printer is in operation, always be aware of possible hazards.

ELECTRIC SHOCK HAZARD
Never open the electronics bay of the printer while the printer is powered on. Before removing the access panel, always power down the printer and unplug the AC power cord.

BURN HAZARD
Never touch the extruder nozzle, the heater block, or the heated bed without first turning off the hotend and heated bed and allowing it to completely cool down. The hotend and heated bed can take up to twenty minutes to completely cool down. Also, never touch recently extruded filaments. The filament can stick to your skin and cause a burn.

FIRE HAZARD
Never leave flammable materials or liquids on or near the printer when powered on or in operation. Liquid acetone and vapors are extremely flammable.

PINCH HAZARD
When the printer is in operation, be careful never to put your fingers in the moving parts, including the belts, pulleys, gears, wheels, or lead screws.

STATIC CHARGE
Make sure to ground yourself before touching the printer, especially the electronics. Electrostatic charges can damage electronic components. To ground yourself, touch a grounded source.

AGE WARNING
For users under the ages of 18, adult supervision is recommended. Beware of choking hazards around children.

PRODUCT WARRANTY

The Artillery Genius Pro 3D Printer is covered by a limited warranty. For terms and conditions, see https://desk.zoho.com/portal/evnovo/en/kb/articles /evnovo-limited-warranty

OVERALL PROVISIONS

All information in this user manual (“Manual”) is subject to change at any time without notice and is provided for convenience purposes only. Shenzhen Yuntuchuangzhi Technology Co., Ltd. and our respective affiliates and suppliers (“Artillery”) reserves the right to modify or revise this Manual in its sole discretion and at any time and makes no commitment to provide any such changes, updates, enhancements, or other additions to this Manual in a timely manner or at all. You agree to be bound by any modifications and/or revisions. Contact the Artillery Support Team for up-to-date information.

INTELLECTUAL PROPERTY

The design of this Manual and all text, graphics, information, content, and other material are protected by copyright and other laws. The contents are copyright 2021 Artillery. All rights reserved. Certain trademarks, trade names, and logos (the “Marks”) used in this Manual are registered and unregistered trademarks, trade names of Artillery and its affiliates. Nothing contained in this Manual grants or should be constructed as granting, by implication, estoppel, or otherwise, any license or right to use without the written permission of Artillery. Any unauthorized use of any information, materials, or Marks may violate copyright laws, trademark laws, laws of privacy and publicity, and/or other laws and regulations.

DISCLAIMERS

Artillery does not warrant the accuracy or completeness of the information, products, or services provided by or through this Manual and assumes no responsibility for any typographical, technical, or other inaccuracies in this Manual, which is provided “as is” and without any express or implied warranties of any kind, including warranties of merchantability, fitness for a particular purpose, or non-infringement of intellectual property. In connection with your use of this Manual, Artillery shall not be liable to you for any damages whatsoever, be they direct, economic, commercial, special, consequential, incidental, exemplary, or indirect damages, even if Artillery has been advised of the possibility of such damages, including without limitation, loss of business revenue or earnings, lost data, or lost profits. Artillery assumes no responsibility, nor will be liable, for any damages to, or any viruses or malware that may infect, your computer, telecommunication equipment, or other property caused by or arising from your downloading of any information or materials related to this Manual. The foregoing exclusions do not apply to the extent prohibited by law please refer to your local laws for any such prohibitions.

LETTER FROM ARTILLERY

Dear Customer, Thank you for choosing Artillery Genius Pro 3D Printer. This guide will step you through the assembly and the first run of the printer. If you have any problems during assembly, please contact our customer service or visit our official Facebook group at:
https://www.facebook.com/groups/artillerygeniuspro/
For a detailed warranty policy, please visit
https://desk.zoho.com/portal/evnovo/kb/articles/evnovo-limited-warranty
For support, please send an email to support@artillery3d.com
or visit our ticketing page at https://desk.zoho.com/portal/evnovo/newticket Or you can visit our Facebook group at https://www.facebook.com/artillery3d Regards, Artillery

ACCESSORY CHECKLIST

ASSEMBLY

1. Align the XZ gantry to the base, make sure the connector is perfectly aligned to the female connector on the base.
2. The M5 screws used to fasten the XZ gantry to the base are pre-inserted into the extrusion, use the Allen key provided to tighten the screws. Push the aluminum extrusions against the inside of the slot when tight-ening the screws.
3. Assemble the spool holder as shown in picture, then slide it into the slots on the top of the top beam. Then use the knob supplied to fix it in place.
4. Connect the Z stepper motors and filament runout sensor.
5. Loosen the 6 screws holding the carriages on both sides then tighten them ONLY when wheels on Z carriages not properly seating on the aluminum extrusions.
6. Adjust the bed carriage and hotend carriage by turning the eccentric nuts with the wrench supplied.

LEVELING THE BUILD PLATE

The Genius Pro comes with Auto Bed Leveling Sensor, it will perform a self- test when you power on the printer, if it doesn’t, please do not proceed and check on the cables to make sure they’re correctly seated.

1. Home the printer;
2. Heat up the bed and the hotend to 70 ° C and 240 ° C respectively;
3. Go to Tools -> Level;
4. Slide a piece of A4 paper between the nozzle and the build plate;
5. Move the hotend to all 4 corners to repeat step 6;
6. Turn the leveling knob under the bed closest to the nozzle until the piece of paper slides, with just a bit of drag;
7. From the menu, go to Tools -> More and click on Auto-Level;
8. The printer will initialize the auto bed leveling procedure, wait till it finishes;
9. Click EEPROM Save;
10. Do the following only if the nozzle is scratching on the build plate or the nozzle too far from the build plate;
11. Heat up the bed and the hotend to 70 ° C and 240 ° C respectively;
12. Go to Tools -> More -> Z=0;
13. The nozzle will move to the center and at 0 height;
14. Slide the A4 paper between the nozzle and bed again, use +0.025 and -0.025 button to adjust the nozzle distance from the build plate until the piece of paper slides, with just a bit of drag;
15. Click EEPROM Save once you’re happy with the drag on the A4 paper;
16. Repeat Step 2 to Step 9.
17. To enable compensation for auto-leveling, add M420 S1 Z10 after G28 in starting Gcode.

PREPARING SLICING SOFTWARE

This printer works with most slicing software like Slic3r, Cura, Simplify3D, etc. But we will go into detail about Cura software and tell you how to set it up so that you can make your first print. First, please download the software from their official site. After installation and start the software, you should see the following screen, continue until you see Add a printer page:

In the Add a non-networked printer, scroll down to Artillery and choose Artillery Genius, and type in Artillery Genius Pro in Printer name. Then click on Next button.

Set X (Width), Y (Depth) as 220, Z (Height) as 250. Make sure Heated Bed is checked.

Make sure Compatible material diameter is set to 1.75

Drag and drop the STL file (or other supported formats) to the slicer or load the model file with File -> Open File(s)…

From the Profile dropdown, choose the preferred profile.

Click on Slice button.

You can click on Save to Removable Drive or Save to file button to save the sliced file to the memory card/USB Drive.

Save the file to the USB drive/memory card for printing.

Insert the USB Drive / memory card into the printer then click on PRINT.

Choose the file you want to print.

Click on Confirm and the print should start.

SPECIFICATIONS

PRINTING

• Print Technology: Fused Deposition Modeling
• Build Volume: 220x220x250 mm (8.7×8.7×9.8 in)
• Layer Resolution: 100-300 microns
• Filament: 1.75 mm (0.069 in)
• Nozzle Diameter: 0.4 mm (0.015 in)
• Print File Type: Gcode
• Material Compatibility: PLA, PETG, TPU

SIZE & WEIGHT

• Product Dimensions: 430x390x590 mm (16.9×15.4×23.2 in)
• Shipping Box: 528x428x310 mm (20.8×16.9×12.2 in)
• Printer Weight: 9.6 kg (21.2 lbs)
• Shipping Weight: 11.7 kg (25.8 lbs)

ELECTRICAL

• Power Requirements: 110V/220V, 350W
• Connectivity: Memory Card, USB Stick, USB

MECHANICAL

• Construction: Aluminum, ABS
• Build Surface: Glass + Aluminum plate
• Stepper Motors: 1.8° step angle with 1/256 micro-stepping
• XY Positioning Precision: 10 microns
• Z Positioning Precision: 100 microns

CONTACT

Support
desk.zoho.com/portal/evnovo/en/newticket At Artillery, we take pride in offering expert, responsive, friendly customer support to customers around the world. If you need help resolving an issue with your Artillery 3D printer, visit the web address above to submit a ticket

Sales
ytcz@artillery3d.com To learn about other Artillery products, please email the address above.

Feedback
ytcz@artillery3d.com For general questions, or to tell us what’s on your mind, send an email to the address above. We love to hear from you.

References

• desk.zoho.com/portal/evnovo/en/kb/
• desk.zoho.com/portal/evnovo/en/kb/articles/evnovo-limited-
• desk.zoho.com/portal/evnovo/en/newticket
• desk.zoho.com/portal/evnovo/kb/
• Artillery Official Site Discover Our New 3D Printers Sidewinder X4 PRO – Artillery3d
• Zoho Desk | Customer Service Software for Context-Aware Support
• Zoho Desk - Error
• desk.zoho.com/portal/evnovo/en/kb/articles/evnovo-
• desk.zoho.com/portal/evnovo/kb/articles/evnovo-limited-
• desk.zoho.com/portal/evnovo/newticket

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>