Eltako FWS61-24V DC Wireless Weather Data Transmitter Module Instruction Manual
- May 15, 2024
- Eltako
Table of Contents
Eltako FWS61-24V DC Wireless Weather Data Transmitter Module
Specifications
- Model: FWS61-24V DC
- Part Number: 30 000 305 – 2
- Power Input: 24V DC
- Wireless Weather Data Transmitter Module
Product Information
The FWS61-24V DC is a wireless weather data transmitter module designed to provide accurate weather data wirelessly. It operates on a power input of 24V DC, ensuring reliable performance.
Important: Only skilled electricians should install this electrical equipment to prevent the risk of fire or electric shock.
Product Usage Instructions
Installation:
- Ensure the power source is switched off before installation.
- Mount the transmitter module securely in a location with good signal reception.
- Connect the power input of 24V DC to the corresponding power source following electrical safety guidelines.
Operation:
- Once installed, ensure the transmitter module is powered on.
- Allow the module to establish a wireless connection with the weather monitoring system.
- Verify that accurate weather data is being transmitted wirelessly.
FAQ
Q: Can I install the FWS61-24V DC module myself?
A: It is recommended that only skilled electricians install the module to avoid the risk of fire or electric shock.
Q: What is the power input requirement for this transmitter module?
A: The FWS61-24V DC module operates on a power input of 24V DC.
Wireless weather data transmitter module FWS61-24V DC
Only skilled electricians may install this electrical equipment otherwise there is the risk of fi re or electric shock!
- Temperature at mounting location: -20°C up to +50°C.
- Storage temperature: – 25°C up to +70°C.
- Relative humidity: annual average value <75%.
valid for devices from production week 26/20 (see bottom side of housing)
Wireless weather data transmitter module for the seven weather items sent
by the weather data multi-sensor WMS.
With an internal antenna. Only 0.3 watt standby loss.
For installation.
- 45 mm long, 45 mm wide, 18 mm deep. Power (24V DC) is supplied by the switch mode power supply unit FSNT61-24V/6W, (33 mm deep, 45 mm long, 45 mm wide). This switching power supply unit simultaneously supplys the weather data multi-sensor WMS including the heating of the rain sensor.
- It is possible to use a deep wall box for the two devices.
- This weather data transmitter module receives the seven momentary readings of the weather items: brightness (from three cardinal points), twilight, wind, rain and ambient temperature by cable J-Y (ST) Y 2x2x0,8 from the weather data multi-sensor WMS attached to the outside of the building. The readings are sent them at the priority below to the ELTAKO wireless network in the form of wire less telegrams.
- Only one weather data multi-sensor WMS can be connected to a wireless weather data transmission module FWS61. However, several FWS61 can be connected to a multi-sensor MS. The external terminating resistor is only required for an FWS61. At all other FWS61, it must be removed.
- The evaluation is made with a controller, the wireless multifunction sensor relay FMSR14 and/or the actuators FSB14 and FSB71. When the supply voltage is applied, a teach-in telegram is sent immediately and two status telegrams containing the momentary values are sent approx. 60 seconds later. At least every 10 minutes, but also:
- Brightness values west, south and east each from 0 to 99 kLux if a change of a minimum 10% occurs.
- Twilight values from 0 to 999 Lux if a change of a minimum 10% occurs.
- Wind speeds from 0 to 70 m/s. From 4 m/s to 16m/s, the momentary values are sent immediately 3 times at intervals of 1 second. After that, further value increases are sent within 20 seconds. Dropping wind speeds are sent progressively delayed by 20 seconds. Rain values at the start are sent immediately 3 times. After the rain stops, a telegram is sent within 20 seconds.
- Temperature values from -40.0°C to +80.0°C are sent every 10 minutes together with all the other values in a status telegram. Monitoring weather data multisensor function and line break. If the weather data message from weather data multi-sensor WMS is not sent for 5 seconds, the FWS61 immediately sends an alarm telegram which is repeated every 30 seconds. The alarm telegram can be taught in as a switch telegram in an actuator to initiate further action as required. In addition, the two status telegrams containing the values brightness 0 Lux, twilight 0 Lux, temperature -40°C (frost), wind 70 m/s and rain are sent. When a message is again detected from the weather data multi-sensor WMS, the alarm stops automatically.
Typical connection
Manuals and documents in further languages
https://eltako.com/redirect/FWS61-24V_DC
THE UNIQUE WIRELESS PROFESSIONALSMART HOME STANDARD
Frequency: 868.3 MHz
Transmit power: max. 10 mW
Hereby, ELTAKO GmbH declares that the radio equipment type FWS61-24V DC is in com pliance with Directive 2014/53/EU. The full text of the EU declaration of con-formity can be accessed via the QR code or the internet address under ‘Documents’.
Must be kept for later use!
ELTAKO GmbH
D-70736 Fellbach Technical Support English:
+49 711 943 500 25
technical-support@eltako.de
03/2024 Subject to change without notice.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>