TeeHO TK001 Keyless Entry Door Lock Installation Guide

TeeHO TK001 Keyless Entry Door Lock

Thank you for purchasing our products. Please review this manual thoroughly before operating your device. All pictures in this manual are for illustration purposes only. Actual products may vary due to product upgrades.

TOOL REQUIRED

• Do not use an electric screwdriver during installation.

IMPORTANT

• Do not load batteries until lock is completely installed.

At a Glance

How to Use

• UNLOCK the door from the outside

• LOCK the door from outside

• Auto Lock Mode

  • In Auto Lock mode, the bolt will extend out automatically in 30 seconds after unlocking.

• Manual Mode

  • Press any key on the keypad for 2 seconds.

• UNLOCK the door from the inside

  • Rotate the thumb turn to the Unlock position.

• Auto Lock Mode

  • In Auto Lock mode, the device will be locked automatically.

• Manual Mode

  • Rotate the thumb turn to Lock Position

Definitions

• Master Code

  • Required for programming and feature settings. Master code can be used to unlock the door under vacation mode. The default master code needs to be changed before programming. Property owners & managers should keep this information confidential.

• Auto Lock

  • Automatically locks the deadbolt 30 seconds after unlocking. This feature is off by default. You can customize the Auto-Lock time delay between 10 and 99 seconds.

• Key Unlock
  Key Unlock is always available when the batteries are completely dead or valid User Codes are forgotten.

• Low Battery Indicator

  • If you hear 10 beeps along with 10 red lights flashing after pressing any key to lock or unlock the door, that’s an alert for replacing batteries. Please replace with 4 brand new AA alkaline batteries and do not mix used and new batteries. All settings are stored in the lock while the batteries are removed and replaced.

• Wrong Entry Limit

  • After 10 unsuccessful attempts at entering an invalid PIN code, the unit will shut down for 3 minutes.

• Silent Mode

  • The beep sounds when pressing the keypad can be muted. But you will still hear low battery and system alerts.

• Vacation Mode

  • This is a security feature for you when you are leaving your home for a vacation or long trip. Enabling vacation mode will restrict all user codes until the master code is entered on the keypad. If the lock is unlocked by the thumb turn from the inside, the lock will sound an alarm.

• One-Time User Code

  • This code only can be used once and will be automatically deleted after used.

• Unlock with Fake code

  • Users can prevent pin code exposure from strangers by entering random digits before or after pin code.

Code Format

1. Master Code(4 to 10 digits): The default Master Code is 12345678. It is required that you change it to a code of your own before programming.
2. User Code : 20 User Codes (4-10 digits), 1 one-time User Code can be programmed and stored in the lock.
3. Both Master Code and User Code don’t support the following combination of numbers.

INSTALLATION OVERVIEW

Parts List

Installation Instructions

Prepare the door and check the dimensions

A. Measure to confirm that the hole in the door is 2-1/8″ (54mm).

Measure to confirm that the hole in the door edge is 1″(25mm).

B. Measure to confirm that the backset is either 2-3/8″ or  2-3/4″ (60mm or70mm)

C.Measure to confirm that the door is 1-3/8″ to 2″ (35mm to 50mm) thick.

D. Make sure the hole in the door frame is drilled a minimum of 1″ (25mm) deep.

STEP 2 : Install the latch and strike

C. Use a screwdriver to test if the deadbolt works smoothly.

D. Install strike on the door frame.

STEP3: Install exterior assembly

A. With the latch fully retracted (in the unlocked position), route the cable below the latch, and insert the torque blade through the slot in the latch.

B. Secure the mounting plate with the supplied screws. Do not overtighten screws.

STEP 4.Install interior assembly

STEP 5. Detect left/right-hand door installation

Reset the lock to teach the lock the orientation of the door.

IMPORTANT: This step is required and crucial for the lock to operate properly.

A.While the door is OPEN and UNLOCKED, load 3 AA batteries into the battery compartment.
Note : For long last, please use all new,  non-rechargeable alkaline batteries only.

B.Press and hold the Reset button on  the interior assembly by using thereset tool.

C. Load the 4th battery and keep holding the reset button for 3 seconds, until you hear the sound of “beep”. The latch bolt will extend to learn the orientation of the door automatically.

Quick Set Up

Factory Default Settings

• How to Reset?

•   IMPORTANT: The resetting will delete all User Codes stored in the lock.

• Step 1. Keep the door open and unlocked.

• Step 2. Press and hold the Reset button, at the same time take out one battery and then place it back.

• Step 3. Keep holding the Reset button for 3 seconds, until you hear the sound of “beep” and the latch will extend automatically.

Troubleshooting

Why does not the latch extend but the motor is rotating when resetting my lock?
Improper installation may have caused the issue. Please follow the steps to review:

1. Please make sure the latch and strike are aligned.
2. Please slightly loosen the mounting screws on the external assembly keypad and the latch bolt if the screws are over-tightened.
3. Please open your door and reset the lock.

• Why does not the latch extend and the motor isn’t rotating when resetting my lock?
  • The deadbolt latch should be retracted(unlocked) through all your entire installation process.
  • The thumb turn should be vertical in your installation steps 4C and 5A.
  • Please open your door and reset the lock.
• When I attempt to lock/unlock my deadbolt, why does the latch go in and out for a few times?
  • It happens when the latch and strike are misaligned. Please make sure the bolt hole on the door frame is at least 1 inchdeep, so that the bolt can be fully extended.
  • Please check if the door can be closed properly, the deadbolt should not impact the strike or door frame on the door frame side, it should go directly into the hole properly.
• Why does my lock only work properly when the backup key is in? Why am I unable to pull the key out in the unlocked position?
  • You may need to re-install the whole lock.
  • Please make sure when you start to install, the lock is in unlocked status;
  • Please make sure the thumb turn is vertical.
  • Please do not put the backup key in the lock during the installation.
• What does 5 short and fast beeps mean while programming?
  • It alerts you either time-out or wrong entry.
  • Please be sure to complete each setting step within 5 seconds.
  • Please change the default master code in the first time programming.
  • Please be sure the user code is with correct format and with 4 to 10 digits.
• What if I forget my Master Codes?
  • If you forget your Master code, resetting your lock, then the original master code (12345678) works, and all previous user codes were erased.

Safety Information

Information & Safety Warnings

• Protect your User Codes and Master Code.
• Restrict access to your lock’s interior assembly and routinely check your settings to ensure they have not been altered without your knowledge.
• Do not use an electric screwdriver during installation.
• This manufacturer advises that no lock can provide complete security by itself.
• This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property.
• No lock can substitute for caution, awareness of your environment, and common sense.
• Care should be taken to ensure a long-lasting finish. When cleaning is required use a soft, damp cloth. Using lacquer thinner, caustic soaps,  abrasive cleaners or polishes could damage the coating and result in tarnishing.
• The lock is water resistant. It can withstand water splashes; however, do not let water and liquids get into the lock.
• Avoid exposure to direct sunlight. Long-term exposure to direct sunlight may damage the lock.

Installation Instructions of Handleset

Parts list

Prepare the door and check the dimensions

Latch backset adjustment

Install latch and strike

Install Handleset

Install Handle Lever

Documents / Resources

| TeeHO TK001 Keyless Entry Door Lock [pdf] Installation Guide
20231108 TK001, TK001, TK001 Keyless Entry Door Lock, Keyless Entry Door Lock, Entry Door Lock, Door Lock, Lock
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>