TeeHO TE002W Smart Lock Instruction Manual
- June 10, 2024
- TeeHO
Table of Contents
TeeHO TE002W Smart Lock
Product Information
The product is compliant with the Federal Communications Commission (FCC) regulations and the Innovation, Science, and Economic Development (ISED) regulations.
FCC Statement
The FCC regulates the use of radio-frequency energy in the United States. This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
ISED Statement
The ISED regulates radio, spectrum, and telecommunications equipment in Canada. This product meets the requirements of ISED Canada. The ISED label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational, and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements (TTR).
Product Usage Instructions
Before using this product, make sure that you have read and understood all instructions provided in the user manual. Failure to follow these instructions may result in damage to the product or injury to the user.
To use the product:
- Ensure that the product is properly connected to a power source and any necessary peripherals.
- Follow the instructions provided in the user manual to turn on the product.
- Refer to the user manual for detailed instructions on how to use the product.
- When finished using the product, follow the instructions provided in the user manual to turn off and disconnect the product from any power source or peripherals.
If you experience any issues while using the product, refer to the troubleshooting section of the user manual or contact customer support for assistance.
- Register an account in KK Home App
- Scan the QR code on the inside pa,el to add 1E002W to the device list
- Follow the setup steps to get started.
Parts List
- Prepare the door and check the dimensions
- Choose faceplate
- Is the slotted hole centered in the door hole?
- Install latch and deadbolt
- IMPORTANT: Keep the latch in an unlocked position before installation.
Parts identification
Install exterior assembly
Install interior assembly
Do not completely load the batteries installed. until lock
Detect left/right-hand door installation
Parts illustrations
The default master code is 12345678. It’s required that you change it to a
code of your own before programming.
ITEM SPECIFICATIONS REMARKS
- Battery (Use only new and non-rechargeable Alkaline batteries for the best results.)
- AA alkaline battery ×4 (Operation voltage:4.6~6.0V)
- Last up to one year (10 times open/close per day)
Exterior assembly Interior assembly
How to use it?
- Unlock the door from outside
- Unlock the door from inside
Quick set up
- The default master code is 12345678. It’s required that you change it to a code of your own before programming.
- When a setting is unsuccessful, the indicator light will flash red.
Information and safety warnings
- Do not load batteries until the lock is completely installed.
- Protect your user codes and master code.
- Restrict access to your lock’s interior assembly and routinely check your settings to ensure they have not been altered without your knowledge.
- This lockset is designed to provide the highest standard of product quality and performance. Care should be taken to ensure a long-lasting finish. When cleaning is required use a soft and damp cloth. Using lacquer thinner, caustic soaps, abrasive cleaners, or polishes could damage the coating and result in tarnishing.
- Master PIN Code (4-10 digits): The default master pin code is “12345678”, It’s required that you change it to a code of your own before programming.
- User PIN Code (4-10 digits): A total of 20 user codes(and one temporary one-time user code) may be programmed.
- Both master and user PIN codes don’t support the following combination of numbers below.
Definitions
Master Code
- Required for programming and feature settings. A master code can be used to unlock the door under vacation mode. The default master code needs to be changed before programming.
- The property owner/manager should keep this information confidential.
Auto Lock
- Automatically locks the deadbolt 30 seconds after unlocking. This feature is off by default. You can set the Auto-lock time delay between 30 and 180 seconds.
Wrong Entry Limit
© After 10 unsuccessful attempts at entering an invalid PIN code, the unit
will shut down for 3 minutes.
silent Mode
© The beep sounds when pressing the keypad can be muted. But you will still
hear low battery and system alerts.
Vacation Mode
- This is a security feature for you when you are leaving your home for a vacation or a long trip. Enabling vacation mode will restrict all user codes until the master
code is entered on the keypad. If the lock is unlocked by thumb turn, the lock will sound an alarm.
One-Time User Code
- This code can only be used once and is automatically deleted when used.
Unlock with Fake Code
- Users can prevent pin code exposure from strangers by entering random digits before or after the pin code.
Factory default settings
Restore factory default settings
This procedure will delete all user codes associated with the lock.
- Keep the door opening and unlocking;
- Press and hold the reset button, taking out one battery and then place it back at the same time;
- Keep holding the reset button for 3 seconds until you hear the sound of “BEEp”
Troubleshooting
Installation
Operation
If the lock appears to be damaged or does not operate properly, please contact customer service for further assistance.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution : Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator and your body. This device
contains licence-exempt transmitter(s)/receivers) that comply with Innovation,
Science, and Economic Development Canada’s license-exempt RSS(s). Operation is
subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device. The digital apparatus complies with Canadian CAN ICES – 3 (B)/NMB – 3(B).
This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>