TeeHO Door Lock Instruction Manual

TeeHO Door Lock

Part list

The details of part identification is shown on following page

Prepare the door and check dimensions

Measure to confirm that the hole in the door is 2-1/8″(54mm).

Measure to confirm that the backset is either 2-3/B”or 2-3/4″(60 or 70mm).

Measure 1″(25mm). to confirm that the hole in the door is 25cmm.

Measure to confirm that door thickness is between 1-3/8″ and 2″ (35mm to 50mm).

Choose faceplate

Is the slotted hole centered in the door hole?

Install latch and deadbolt

IMPORTANT: Keep the latch in unlocked position before installation

Parts identification

Install exterior assembly

• Route the cable below the latch.

• IMPORTANT: Bolt must be in unlock position.
  Note horizontal orientation of torque blade

• Route the cable through the hole in the mounting plate.
  

• Secure the mounting plate with the supplied screws.

Install interior assembly
Do not load batteries until lock is completely installed.

• Remove the battery cover.

• Connect the cable end ensure tight cable connection.

• Rotate the Thumb turn in vertical position and insert the horizontal orientation of torque blade into the interior assembly lock switch.

• Secure the interior assembly with the supplied screws.

• Test the lock by rotating the thumb turn to see if the bolt can be extended and retracted smoothly.

Detect left/right hand door installation
IMPORTANT: This step is required and crucial for the lock after installation

• While the door is open and unlock, load 3AA batteries into the interior assembly.

• Press and hold the reset button on the interior assembly using the reset tool provided in package

• Keep holding the reset button, and load the last battery. Hold the reset button until you hear the long sound of “BEEP”. The lock will automatically go into locking position. This is for the smart lock to memorize the orientation of the door.
  

Parts illstrations

Battery (Using only new and non-rechagerable Alkaline betteries for the best results.)|  AA alkaline battery ×4 (Operation voltage: 4.6-6.0V)| Last up to one year (10 times open/close per day)

How to use?

• Unlock the door from outside

• Unlock the door from inside

Lock the door from outside

• Auto re-lock mode
  In auto re-lock mode, the bolt will extend out automatically in 30 seconds after unlocking

• Manual mode
  Press any of the buttons on keypad for 2 seconds.

Lock the door from inside

• Auto re-lock mode
  In auto re-lock mode, the bolt will extend out automatically in 30 seconds after unlocking.

• Manual mode
  Rotate the turn piece to lock position.

Quick set up

The default master code is 12345678. It’s required that you change it to a code of your own before programming

When setting is unsuccessful, the indicator light will flash red.

Information and safety warnings

A do not load batteries until lock .. 1s completely installed.

• Protect your user codes and master code.
• Restrict access to your lock’s interior assembly and routinely check your settings to ensure they have not been altered without your knowledge.
• This lockset is designed to provide the highest standard of product quality and performance. Care should be taken to ensure a long-lasting finish. When cleaning is required use a soft and damp cloth. Using lacquer thinner, caustic soaps, abrasive cleaners or polishes could damage the coating and result in tarnishing.

1. Master PIN Code (4~10 digits): The default master pin code is “7 2345678”, It’s required that you change It to a code of your own before programming.
2. User PIN Code (4-10 digits):A total of 20 user codes(and one temporary one-time user code) may be programmed.
3. Both master and user PIN COOes don’t support the following combination of numbers below.

Definitions

1. Master Code
   • Required for programming and feature settings. Master code can be used to unlock the door under vacation mode.
   • The default master code needs to be changed before programming.
   • Property owner/manager should keep this information confidential.
2. Auto Lock
   • Automatically locks the deadbolt 30 seconds after unlocking.This feature is off by default.You can set the Auto Lock time delay between 1 O and 99 seconds.
3. Wrong Entry Limit
   • After 10 unsuccessful attempts at entering a Invalid PIN code, the unit will shut down for 3 minutes.
4. Silent Mode
   • The beep sounds when pnessing keypad can be muted. But you will still hear low battery and system alerts.
5. Vacation Mode
   • This is a security feature for you when you are leaving your home for vacation or long trip. Enabling vacation mode will restrict all user codes until master code is entered on keypad. If the lock is unlocked by thumb tum, the lock will sound an alarm.
6. One Time User Code
   • This code can only be used once and Is automatically deleted when used.
7. Unlock with Fake Code
   • User can prevent pin code exposure from strangers by entering random digits before or after pin code.

Factory default settings

SETTINGS : FACTORY DEFAULT

• Master code , 12345678
• Auto lock Disabled
• Silent mode : Disabled
• Wrong code entry limit 10 times : 1
• Shutdown time 13 mins : 1
• Vacation mode Disabled

Restore factory default settings
This procedure will delete all user codes which aa associated with the lock.

1. Keep the door opening and unlocking;
2. Press and hold the reset button, taking out one battery and then place it back at the same time;
3. Keep holding the reset button for 3 seconds until you hear the sound of “BEEP”.

Troubleshooting

Installation

• Make sure the backset on the latch is set to the proper length. Refer to Installation Instructions
• Make sure prior to Installation latch bolt Is retracted and key Is not In lockset when installing the deadbolt. Refer to Installation Instructions
• Please restore to factory setting and enter the default Master Code to set up the lock. Refer to Programming Instructions

Feel a bump while turning the thumb turn or the key?| Check If the length of mounting screws Is correct.
Check if the turn piece is in vertical (unlock) position.

• Please refer to Programming Instructions to enable the Auto-Lock

Fail to set up the lock.| Please make sure the lock is installed correctly.

• Please install fresh batteries and make sure the cable is connected correctly.
• After installation, reset the lock to complete the bolt direction setting.

Operation

replace with four new batteries for the best performance (alkaline batteries only).
Keypad not responding.|

• Make sure the batteries are installed properly.
• The batteries are getting low if the battery indicator keeps flashing.
• Please replace with four new batteries for the best perfonnance (alkaline batteries only).
• Make sure the cable is well-connected to the port, and was not damaged during installation.
• Please make sure the lock has been set up and complete the bolt direction determination.

Master Code can not be changed.| Please refer to Programming Instructions to restore factory settings and reprogram all codes.
What should I do if wrong code was entered?| Press CID button once and continue to Input code according to regular procedures.
I forgot my Master Codes.| Perform a reset in order to erase all passcodes. Once the reset is complete, all passcodes will be erased and the Master code will return to the default master code 12345678.
Can not add a new User Code.|

• Make sure the whole code entering process is completed within 1O seconds, otherwise the unit will time out.
• Make sure the Master Code has been entered correctly.
• The new User Code will not be accepted when the capacity is full. Try to delete any or some existing User Codes and then add new one(s) again. A User Code must be at least 4 to 10 digits.

“Auto lock” does not function.|

• The batteries are low on power If the battery Indicator keeps flashing.
  Please replace with four new batteries for the best performance (alkaline batteries only).

Lockset is not able to unlock / lock by keypad.|

• Make sure you have entered the correct User Code.
• The battery is low if the battery indicator light keeps flashing. Please replace with four new batteries.
• Make sure the cable is firmly connected.
• Check the cable for any damage that may have occurred during installation.
• Make sure the batteries are properly installed. (Alkaline batteries only.)
• Check the strike plate to make sure it is properly aligned and clear so the bolt can freely move in the hole.

Lockset is unable to reset.|

• Please refer to Programming Instructions to restore factory settings and reprogram all codes.
• The battery Is low If the battery Indicator light keeps flashing. Please replace with four new batteries.

If the lock appears to be damaged or does not operate properly, please contact customer service for further assistance.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>