TeeHO TE007 Smart Lock Installation Guide

TE007 Smart Lock
Installation Guide

TE007 Smart Lock

Thank you for purchasing our products. Please review this manual thoroughly before operating your device. All pictures in this manual are for illustration purpose only. Actual product may vary due to product upgrade.
TOOL REQUIRED:
Do not use an electric screwdriver during installation.

Installation Overview

Parts List

Step1. Prepare the door and check dimensions

|
---|---
A. Measure to confirm that the hole in the door is 1-1/2” or 2-1/8″ (38mm or 54mm)
Measure to confirm that the hole in the door edge is 1″ (25mm).| B. Measure to confirm that the backset is either 2-3/8″ or 2-3/4″ (60 or 70mm)
****|
C. Measure to confirm that the door is 1-3/8″ to 2″ (35 mm or
50mm) thick.| D. Make sure the hole in the door frame is drilled a minimum of 1” (25mm) deep, to leave enough space for the deadbolt to extend into the door frame when the door is locked.

Notes: Make sure the door frame is aligned with the door. There are no obstructions stuck in the door frame.
Step2. Install the latch and strike
A Determine backset and adjust the latch

Hold the latch in front of the door hole, with the latch face flush against the door edge. Is the slotted hole centered in the door hole?
YES

No adjustment is required. Proceed to next step.
NO

Slotted hole is NOT centered. Rotate and pull the latch as shown to  extend latch.

B. Install the latch

C. Use a screwdriver to test if deadbolt works smoothly.

D. Install strike on the door frame.

STEP 3. Install exterior assembly
**IMPORTANT:
Before installation, make sure the latch is fully retracted (in the unlocked position) A.** Measure the diameter of the hole in the door.

B. With the latch fully retracted (in the unlocked position), route the cable below the latch, and insert the tailpiece through the slot in the latch.

C. Secure the mounting plate with the supplied screws. Do not overtighten screws.

STEP 4. Install interior assembly
A. Push the battery cover out in the direction as illustrated.
IMPORTANT:
Do not load batteries until lock is completely installed.

B. Determine the door is right handed or left handed.
Notes:
If the direction of the slide switch is set incorrectly, it can be reset in DDLock App. Right handed door
Move the slide switch to “R”
Turn the thumb turn to the Vertical position.
Left handed door
Move the slide switch to “L”
Turn the thumb turn to the Horizontal position.
STEP 4. Install interior assembly
C. Insert the cable connector to the socket. Push the connector in firmly until it is completely attached.

D. Attach Interior Assembly to Mounting Plate and tighten 3 Screws.

E. Insert 4 AA Alkaline batteries and put on the battery cover.

PROGRAMMING INSTRUCTIONS

At a Glance

How to Use
UNLOCK the door from outside

LOCK the door form outside

UNLOCK the door from inside
Rotate the thumb turn to Unlock position.

LOCK the door from inside
Auto Lock Mode
In Auto Lock mode, the device will be locked automatically.
Manual Mode
Rotate the thumb turn to Lock Position.

Definitions

Programming Basic

• Master Code
  Required for programming and feature settings. The default master code needs to be changed before programming.
  Property owner & manager should keep this information confidential.

• Auto Lock
  Automatically locks the deadbolt 5 seconds after unlocking. This feature is off by default. You can customize the Auto Lock time delay between 1 and 900 seconds.

• Key Unlock
  Key Unlock is always available when the batteries are completely dead or valid User Codes are forgotten.

• Low Battery indicator
  If you hear 3 beeps along with 3 red light flashing after pressing any key to lock or unlock the door, that’s an alert for replacing batteries.
  Please replace with 4 brand new AA alkaline batteries and do not mix used and new batteries. All settings are stored in the lock while the batteries are removed and replaced.

• Wrong Entry Limit
  After 5 unsuccessful attempts at entering an invalid PIN code, the unit will shut down for 2 minutes.

• Silent Mode
  The beep sounds when pressing keypad can be muted. But you will still hear low battery and system alerts.

• Unlock with Fake code
  User can prevent pin code exposure from strangers by entering random digits before or after pin code. The total password length is within 16 digits.

Factory Default Settings

How to Reset?
Press and hold the Reset button on the interior assembly by using the reset tool, stop holding until you hear a short beep and see 1 green light flash.
IMPORTANT: The reset button function must be turned on in the DDLock App before resetting.

DDLOCK USE GUIDE

HOW TO REGISTER
STEP 1. Download “DDLock’” App in Google Play or App Store.

https://onelink.to/ddlock

Fill out this and then tap “Get Code”.
You will be sent a verification code to verify your account!
Once you receive it, tap on “Register”
Notes:
The DDLock app is needed to use this lock. If this lock was professionally installed (or installed by someone other than the homeowner), make sure this step is performed by the homeowner.

Pairing Your Lock

Admin Passcode Management After pairing the lock with DDLock, the admin passcode will be changed to a random 7 digit number, you can check the new admin passcode by following the picture guide below. And you can change it to your own administrator  password.

Lock Page Overview

Unlock/Lock
Unlock/Lock using phone’s bluetooth| Settings Page
View and modify settings
---|---
Passcode
Generate 6 different types of passcodes| Authorized Admin Page
Create and edit admins
eKey Page
View and modify current eKeys| Cards
Set up your cards here
Records Page
View entry times, attempts and methods| Fingerprints Page
Set up fingerprints

Notes: Some of these icons may not appear if the Gateway is not connected to the lock.

APP Unlock /Lock

To unlock the lock, tap this icon once.
To lock the lock, press and hold on this icon.

Passcode

IC Card

Choose the validity period of the lock. Once the lock says “Please swipe your card”, place the card against 5 onthe keypad.
If you hear a long beep, the card can be used to unlock  your lock.

Fingerprints

eKeys

Enter recipient’s username. It will be the phone number or email address during registration.
eKeys do not require wife or Bluetooth to be sent or revoked.

Authorized Admin
Authorized Admins are similar to eKeys; however, an authorized admin can do the following:

Tap on “Authorized Admin” Set Timed Admin or Permanent Admin.

Passage Mode & Auto-Lock

Auto-lock will automatically lock the lock when it has be opened after 5 seconds by default. This can be adjusted with Passage Mode and Auto-lock timer.
Outlined below is how to adjust these settings related to auto-lock.
Passage Mode disables auto-lock during a set schedule.

Lock Settings

Here are some settings you should familiarize yourself with.
Under|Ba8ie8} you can view and change information such as Lock Name.
(GateWay| shows signal strength if Gateway is connected.
With [Remote Unlock on and a Gateway connected, you can remotely unlock/lock your lock.
(DeekSouind adjusts the locks sound level.
(IPSFMFOMPAROHEMIGEK allows for the transfer of passcodes and cards from one lock to another.
Delete will remove the lock from your account and clear any settings one the lock. You must be near the lock to do this.

Troubleshooting

Why the lock won’t accept any inputs after | entered a code or fingerprint incorrectly for so many times?
The lock will shut down for 2 minutes after 5 unsuccessful attempts at entering an invalid code or fingerprint.
You can unlock the lock once in the App or wait 2 minutes to continue.
How do I lock manually from outside?
Press and hold # to lock the lock from outside.
The batteries are completely dead before | replace new batteries.
When the batteries are completely dead, the physical keys are available to unlock.
How do! share access of the lock to my family members?
Go to DDLock App, in eKeys or Authorized Admin, it can share access 0of the lock to your family.
Why the thumb turn won’t turn to lock/unlock?
The door direction might be set wrong during the installation, please follow the Installation guide or video to re-install the lock.
When !| tap on Lock in App, the deadbolt unlocked and retracted; When | tap on Unlock in App, the deadbolt locked and extended.
The door direction has been set wrong. It can be changed in Settings >
Door opening direction in DDLock App.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential  installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no  guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is  encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference  that may cause undesired operation.
RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

ISED Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.
   The digital apparatus complies with Canadian CAN ICES ‐3 (B)/NMB‐3(B).

Information & Safety Warnings

• Protect your User Codes and Master Code.
• Restrict access to your lock’s interior assembly and routinely check your settings to ensure they have not been altered without your knowledge.
• Do not use an electric screwdriver during installation.
• This manufacturer advises that no lock can provide complete security by itself.
• This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property.
• No lock can substitute for caution, awareness of your environment, and common sense.
• Care should be taken to ensure a long-lasting finish. When cleaning is required use a soft, damp cloth. Using lacquer thinner, caustic soaps, abrasive cleaners or polishes could damage the coating and result in tarnishing.
• The lock is water resistant. It can withstand water splashes; however, do not let water and liquids get into the lock.
• Avoid exposure to direct sunlight. Long-term exposure to direct sunlight may damage the lock.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>