SALAMANDER PLANO 100 Medium Installation Guide

June 4, 2024
SALAMANDER

PLANO 100 Medium
Installation GuideSALAMANDER PLANO 100 Medium

IMPORTANT SAFETY INSTRUCTIONS

  • Carefully inspect the mount for shipping damage or missing parts. If any damage is apparent or you are missing parts contact Salamander Designs at 800-535-5659.

  • Read ALL assembly instructions before assembly. If you have any questions, please contact your installation contractor or Salamander Designs.

  • Mounts must be attached as specified in assembly instructions. Improper installation can result in serious personal injury.

  • This TV mount is intended for use with Flat-Panel TVs 23-42” with a maximum weight capacity of 100 lbs.

  • Use of this mount with products heavier than the maximum weight or larger than the size indicated may result in the collapse of the mount causing possible injury.

  • The mount is designed to be installed using wall studs or supporting frames. Not for use on steel stud walls or old cinder block walls.
    Installation to these types of walls will require other fasteners than those provided.

  • Use the mounting screws provided and DO NOT OVER-TIGHTEN mounting screws.

Unpacking
Unpack all content and check to ensure that all of the parts are in proper condition. To help protect the environment, use the appropriate recycling and discarding methods for the packaging items. The boxes used for the packaging of this product may be recycled or reused.

TOOLS

Tools Required for Assembly:

SALAMANDER PLANO 100 Medium - Figure 1

HARDWARE

SALAMANDER PLANO 100 Medium - Figure 2

PARTS

SALAMANDER PLANO 100 Medium - Figure 3

Install Wall Bracket

SALAMANDER PLANO 100 Medium - Figure 4

For wood constructions, locate a framing stud at the desired location using a stud finder device.| Align and level the Wall Bracket (I) with the framing stud.
Using a pencil mark top and bottom holes as shown.
Note: It is important to utilize one of the three center holes when installing wood framing.
SALAMANDER PLANO 100 Medium - Figure 5

Predrill mounting holes 2.5” (64 mm) deep using a 3/16” (4.5 mm) bit for wood construction; a 3/8” (10 mm) bit for masonry construction.| Install Lag Screws (B) with Washers (E), through Wall Bracket (I), level and tighten firmly with Allen Key (A). For Masonry Installation use Plastic Wall Plugs (C).

Attach TV Brackets

SALAMANDER PLANO 100 Medium - Figure 6

Align TV brackets (II) with FOUR TV mounting holes.
Attach using the supplied Mounting Screws (J). To determine the correct thread size and length, refer to the TV manufacturer’s installation manual.
NOTE: Washers (D) are necessary when using M4 and M5 mounting screws.
Spacers (F) can be utilized in applications where interferences at the back of the TV prevent proper fit of the TV Brackets (II). NOTE: It is always necessary to fasten the TV at four points for proper installation.

SALAMANDER PLANO 100 Medium - Figure 7

If TV mounting pattern exceeds 13” (330 mm) in width or 8-1/2” (216 mm) in height, use supplied Extension Wings (III) to expand mounting. Extension Wings (III) are fastened to TV Brackets (II) using Flat Heads (G), Washers (E), and Hex Nuts (H) prior to mounting to TV.
If TV mounting pattern exceeds 13” (330 mm) in width or 8-1/2” (216 mm) in height, use supplied Extension Wings (III) to expand mounting. Extension Wings (III) are fastened to TV Brackets (II) using Flat Heads (G), Washers (E), and Hex Nuts (H) prior to mounting to TV.

SALAMANDER PLANO 100 Medium - Figure 8

Pull on black cord to unlock Click
Fasteners and hook TV Brackets (II)
onto Wall Bracket (I) from top.| Center TV Brackets (II) on Wall Bracket (I)
and push black Click Fasteners up into lock position.| Install Pad Lock (IV).

SALAMANDER DESIGNS LIMITED WARRANTY

Salamander Designs Ltd. (Salamander) provides the following Limited Warranty.
The Limited Warranties herein described for the specific products listed below shall be in lieu of any other warranty, expressed or implied, including but not limited to any implied warranty of merchantability or fitness for a particular use.
These Limited Warranties do not cover damages incurred in shipment, failures caused by other products not supplied by Salamander, or failures due to accident, misuse, abuse or alteration of the product. Salamander’s sole liability and the purchaser’s exclusive remedy shall be for the repair, or at Salamander’s option, for the replacement of the defective part as provided herein. Notwithstanding the above, if replacement parts for defective materials are not available, Salamander reserves the right to make reasonable compensation in lieu of repair or replacement. Liability for incidental or consequential damages under the warranty is excluded. Some states do not allow the limitation of incidental or consequential damages. Therefore, the above limitation may not apply in certain instances. The defective product must be given Return Authorization by Salamander and is to be returned to the factory prepaid, in the original carton and packing materials. Any damage incurred in a shipment, not in original packing shall be the responsibility of the owner. Warranty repairs will be returned to the owner
prepaid, within the continental U.S.A. only. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
Salamander provides a five (5) year Limited Warranty from the date of the purchase, on material damage and/or manufacturing defects. Salamander guarantees that if, during the warranty period, any defects should occur in the product resulting from faulty material and/or assembly, as assessed by Salamander, the product will be repaired or, if necessary, replaced free of charge. The warranty expressly does not apply to normal wear and tear that becomes apparent after normal use.
During the mounting of the product, instructions for the installation and use of
the television must be followed precisely. Correct mounting is essential. For maximum weights, screen size, and correct application, please refer to the product installation instructions. Failure to comply with these requirements or the occurrence of any of the following circumstances will result in the termination of any otherwise applicable  Limited Warranty:
a. If the holes in the wall required for the installation of the product were not drilled in accordance with the instructions for use of the product, or if the product was not properly installed or used.
b. If you (or third parties) – without Salamander’s or your Salamander dealer’s prior knowledge and permission – carried out work or repairs on the product.
c. If a defect is the result of external causes, i.e. in the case of abnormal types of damage caused by climatological, thermal, mechanical or other external influences.
d. If the product is not used in accordance with its intended use or if it is damaged as a result of negligence.
WARRANTY PROCEDURE
Claims should be made through the dealer from which the product was purchased. The dealer will contact Salamander Designs Ltd. (Salamander) for warranty service. An original sales order number/purchase order number will be required for warranty protection. Salamander’s liability under this warranty is limited to repairing or replacing at  Salamander’s option any part or parts of the product found to be defective in material or workmanship within the applicable warranty period. Salamander in its sole discretion will determine the cause and nature of any defect, the necessity and manner of repair or replacement, and all other matters pertaining to the condition of the product.
LABOR AND SHIPPING CHARGES
Should you be entitled to receive a repair or replacement under this warranty, Salamander will pay the cost of labor, handling and shipping to the consumer for two (2) years from the date of purchase by the original consumer. After that date, the purchaser will be responsible for these costs.

www.SalamanderDesigns.com
©2008 Salamander Designs Ltd.
Doc #503-002 v4.08

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

SALAMANDER User Manuals

Related Manuals