SALAMANDER DESIGNS SQ-WK1 Synergy Wall Mounting Kit Installation Guide

SALAMANDER DESIGNS SQ-WK1 Synergy Wall Mounting Kit

TOOLS REQUIRED

COMES WITH

CAPACITIES (CONTENT)

• SINGLE: 100lbs (45kg)
• TWIN: 100lbs (45kg)
• TRIPLE: 200lbs (90kg)
• QUAD: 250lbs (113kg)

OPTIONAL

• HOLLOW WALL ANCHORS:
• MA/ST2 = 2pk
• MA/ST4 = 4pk
• Each Bracket Requires
• Two Anchors Per Bracket:

BEFORE YOU BEGIN

• Side panels and dividers are mandatory for wall mount installation.
• This bracket is intended for use with:
• Synergy Singles in 20″, 30″, & 40″ heights.
• Synergy Twins, Triples, & Quads in 20″ heights.
• The total weight capacity of each bracket is 100 Ibs. (45kg). (ex 3 brackets provide 300 Ibs. (135kg) (including cabinet weight).
• Carefully inspect your items for shipping damage or missing parts. If any damage is apparent or you are missing parts contact Salamander Designs Ltd. at 800-535-5659.
• Read ALL assembly instructions before assembly. If you have any questions, please contact your installation contractor or Salamander Designs.
• Use with products heavier than the maximum weight or other than the cabinet indicated may result in instability causing possible injury or damage.
• Mounts must be attached as specified in assembly instructions. Improper installation can result in serious personal injury.

1. Install the provided connector bolt in previous foot locations & remove rear panels & fasteners.
   • Tip – If working with an already assembled cabinet, remove and replace leveler feet one at a time.
2. MARK WALL LOCATION
   • A. WOOD CONSTRUCTION – Using a stud finder, mark the locations of the studs in the area to be covered by the cabinet.
   • It may be necessary to shift the cabinet slightly left or right to avoid the mounting brackets being obstructed by the vertical framework of the cabinet.
   • Note: The brackets don’t have to be located in the same relative location in each bay. As long as a bracket is located at least 16″ in the center sufficient capacity will be met.
   • B. MASONRY CONSTRUCTION – Mark the wall 2″ inward from each post
3. MARK HEIGHT LOCATION
   • Move the cabinet from the mounting location. Determine the desired height of the top of the cabinet (28″ (711 mm) is common). From this height subtract 1-3/4″ (45mm).
   • This will be the location of the top bracket hole. Using a level, mark the remaining inter-sectioning locations at the same height.
   • Add a second mark 3-3/8″ (86mm) below the top bracket hole location for the second fastener for each bracket.
4. DRILL WALL HOLES
   • Predrill mounting holes 21/2″ (64mm) deep using a 3/16″ (5mm) bit for wood construction; and a 3/8″ (10mm) bit for masonry construction.
5. INSTALL WALL BRACKETS
   • A. Install brackets using lag screws (Do not completely tighten). Washers are provided to be used between walls and brackets to correct uneven wall surfaces.
   • For masonry insert plastic wall plugs before mounting brackets with lag screws.
6. ADJUST FOR LEVEL
   • B. Tighten brackets using a level for proper alignment.
7. PRE-DRILL & HANG CABINET
   • A. Using two people, lift the cabinet placing onto the bracket. Using a pencil, mark the hole furthest from the wall while one person holds the cabinet tightly in place.
   • B. Remove the cabinet. Using the supplied 1/8″ drill bit, pre-drill marked locations to the depth marked on the bit.
   • C. Reinstall cabinet using self-tapping screws (301-765). Use “U” shaped shims (301-440) to fine level as necessary.
8. INSTALL AN COMPONENTS
   • Configure shelving and install your A/V components.

LIMITED WARRANTY

For five full years, Salamander Designs Ltd. will repair or replace, at our option, any product defective in materials or craftsmanship. Salamander Designs Ltd. will not be responsible for any damage to or destruction of other equipment consequential to our equipment failure. The defective product must be given Return Authorization and is to be returned to the factory prepaid, in the original carton and packing material. Any damage incurred in a shipment not in original packaging shall be the responsibility of the owner. Warranty repairs will be returned prepaid, via UPS within the continental U.S.A. only.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>