MOTECK TW61 Double Motor User Guide

MOTECK TW61 Double Motor

Product Specifications

• Model: Double Motor TW61
• Manufacturer: Moteck
• Distance between bed base axes: 581 millimeters
• Duty Cycle: 10% (2 minutes continuous operation, 18 minutes rest)
• Designed for: Indoor use

Product Usage Instructions

Important Information

• The double motor TW61 is designed for indoor use and should be kept away from humid and wet environments.
• The duty cycle of the motor is 10%, allowing for 2 minutes of continuous operation followed by at least 18 minutes of rest.
• Before installing, ensure that the mains power cord is unplugged. Insert two 9V DC backup batteries into the battery box, wind up the AC power cord and handset wire, and plug the handset connector into the dedicated socket.
• Match the graphic symbols on the motor to the bed frame axis.

Installation Steps

• Check that the mains power cord is unplugged.
• Insert two 9V DC backup batteries into the battery box.
• Securely wind up the AC power cord and handset wire around the hooks to prevent damage.
• Plug the handset connector into the dedicated socket.
• Match the graphic symbols on the motor to the bed frame axis.
• Ensure the bed frame is horizontal before installing the double motor.
• Fix the bed frame axis by pulling out the red latch and moving it along the protective cap.
• Install the motor to the bed shaft ensuring proper engagement.
• Close the protective cap and push back the red latch. Repeat for the other side.
• If using additional actuators, plug them into the socket. Ensure all parts are properly installed before plugging in the power cord.

Bed Frame Control

1. To move the bed board, press and hold the button until it reaches the desired position.
2. Release the button to stop the movement immediately.

FAQ

• Q: Can I operate the double motor TW61 continuously for more than 2 minutes?
• A: No, the duty cycle of the double motor TW61 is 10%, allowing for a maximum continuous operation time of 2 minutes followed by at least 18 minutes of rest.
• Q: Is it safe to disassemble the internal parts of the double motor TW61?
• A: No, please do not disassemble the internal parts of the double motor TW61. If you encounter any issues, contact the manufacturer or qualified service personnel.

Technical changes may be made to improve the product without notice！

Important Information

• The distance between the axes of the bed base must be 581 millimeters.
• The duty cycle of the double motor is 10%, that is, the maximum continuous operation time is 2 minutes, and the rest time is at least 18 minutes.
• If the power cord is damaged, it must be replaced by the manufacturer, its service agent or a similarly qualified person to avoid a hazard.
• Please disconnect the main power cord before removing the protecting cap, and do not disassemble the internal parts of the double motor.
• The double motor is designed for indoor operation and must be kept away from humid and wet environments.
• Any damage caused by the end user due to the installation or disassembly operation will result in the rejection of the warranty and our company does not bear any responsibility of the manufacturer.
• This equipment is not suitable for people with weak physical, sensory or mental capabilities (including children), unless the person responsible for their safety supervises or guides them to this equipment.
• Installation work must be performed by qualified personnel.

Installation

Overview

Installation steps

1. Before installing, do check that the mains power cord is not plugged into the mains power supply.

2. Put two 9V DC backup batteries into the battery box: first, remove the battery box cover, insert the battery, and then put it back in the battery box cover.

3. Wind up the AC power cord and the handset wire around the hooks (as described in the drawing) to avoid any damage during handling.

4. Plug the handset connector into the dedicated socket in the middle position.

5. Match the graphic symbols on the motor to the axis of the bed frame:
   The “Backside” symbol must correspond to the axis linked to the back plate mechanism.
   The “Leg side” symbol must correspond to the axis linked to the footplate mechanism.

6. Before installing the double motor on the bed frame, please check whether the bed frame is in a horizontal position.

7. Pull out the red latch and move it along the protective cap to fix the bed frame axis.

8. Make sure the side position is in the reset position, and then install the motor to the bed shaft.
   Make sure they are engaged properly.

9. Close the protective cap and push back the red latch. Repeat from step 5 to install the other side.

10. Plug additional actuators in the socket (optional). Ensure that all covers and parts are properly installed in place. Plug the power cord into the main power source and the double motor can operate normally.

Bed Frame Control

1. Press and hold the button, the controlled bed board will continue to move, and it will stop automatically when it reaches the end.
2. If you release the button during the process, the movement of the bed board will stop immediately.

Buttons and operation
(take an HD handset as an example)

1. Actuator #1 extends
2. Actuator #1 retracts
3. Actuator #2 extends
4. Actuator #2 retracts
5. Actuator #3 extends
6. Actuator #3 retracts
7. Actuator #4 extends
8. Actuator #4 retracts

Position Memory

Position setting

1. The memory position buttons can store the position of the back and legs. Press the memory set button for 2 seconds, and the LED will flash slowly. Then press the memory position button to store the positions, the LED will flash quickly to confirm the positions have been stored.
2. The memory positions can only be overwritten, not erased.

Execution go to the position

1. Press and hold the memory position button to automatically go to the storage position of the bed, and press any button to stop.
2. The LED indicator light flashes during operation and then stays on when the bed reaches the corresponding position.

Buttons and operation
(take HI handset as an example)

1. Memory set
2. Memory position 1
3. Memory position 2

Backup Battery Function

• In case of a power outage, install two 9V DC batteries in the battery room to retract the actuator.

Remarks
Only for single use, and the standby time is very short.

Terms of Use
The user is responsible for the suitability of MOTECK products, and the products listed on the MOTECK website are subject to change without notice. MOTECK reserves the right to terminate sales or delete any products displayed on the website or listed in its catalog. www.moteck.com

References

• Electric Linear Actuators | Moteck Professional Linear Actuator Company

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>