Power House BSBTH30 ANC Bluetooth Headphone User Manual

Power House BSBTH30 ANC Bluetooth Headphone

USER MANUAL

MODEL: BSBTH30BK

Specs for Products：

• Bluetooth version ：Bluetooth V5.3
• Chipset:Bluetrum
• Frequency: 2.402-2.480GHz
• Transmission Distance: 10m
• Battery Capacity: 3.7V/200mAH
• Charging Time: about 1.5-2 hour
• Charging Voltage: DC 5V
• Working temperature: -40℃ to +85℃
• Playtime ANC ON(100%volume ): 6 hours
• Playtime ANC OFF(100%volume ): 8 hours
• Standby time: about 300 hours
• Speaker Section
• Speaker Dimension: Ф40mm
• Impedance: 32Ω
• Sensitivity: 115dB+/-3dB
• Noise Reduction:22dB+/-3dB
• Frequency Response: 20~20KHz

Function description：

Power On of device： Press and hold the button to power the eadphones ON or OFF. A voice will be heard indicating that the headphones have powered ON or OFF.
Press [ANC]button one second to ANC ON/OFF,prompt”ANC ON/OFF”

Connecting with the 3.5 mm AUX Cable

Plug one connector of the including 3.5mm auxiliary cable into the 3.5mm aux input port on the bottom of the right earcup.

Plug the other connector into the audio output port on your media-playing device.
In auxiliary mode,all playback and volume will be adjusted with the controls on your connected device.

The headphones will automatically power OFF when a 3.5 mm AUX cable is inserted.

Bluetooth Pairing：

1: Power the headphones ON.A voice will be heard,and the LED indicator will flash BLUE and RED.
2: Set your mobile device to search for bluetooth devices.
Select “BSBTH30” from the list of found device.
3: After a successful pairing, a voice will be heard and the LED indicator will begin flashing BLUE intermittently while connected.
In Bluetooth mode,playback and volume can be adjusted with the on-ear controls,or with your paired device.

• Press the button to pause and resume playback.
• Press the and buttons to skip tracks.
• Press and hold the and buttons to adjust volume.

Phone Calls

To use the phone functions on the headphones,you must be connected to a Bluetooth-enabled device.

• Press the    button to answer and end phone calls,Playback will automatically pause ans resume.
• 2x press the the button to dial the last outgoing phone number.
• Press and hold the button for 3 seconds to reject an incoming call.

1. Vol + /Next Track
2. Pause and resume playback/Answer/End phone call/SIRI assist
3. Vol – /Previous Track
4. ANC ON/OFF
5. TYPE-C charging port
6. 3.5mm AUX port
7. LED Indicator
8. Microphone

Charging the Headphones

Plug the small connector of the included charging cable into the charging port on the bottom of the headphones’ earcup.Plug the large connector into a USB power source,such as the USB port on a computer,or a 5V USB wall adapter (not included).

The LED indicator on the headphones will turn RED while charging and turn OFF when finished charging.

Powering ON/OFF

• Press and hold the button for 3 seconds to seconds to power the headphones ON and OFF.
• When powered on,the headphones may automatically reconnect to a nearby previously-paired device with bluetooth enabled.

Using the Active Noise Control

The headphones’ Active Noise Control (noise cancelling) feature reduces unwanted noise from the outside environment.You can use ANC while listening to audio,or use ANC by itself.

• Press the [ANC]button to turn on Active Noise Control (noise cancellation)
• Press the [ANC]button again to turn ANC OFF.

Operation Guide：

LED Light status：

1：Charging status —–Long bright red light,full charged red light was off.
2：Power on—-Flash blue then Red and blue LED indicator flash alternately
3：Pairing status—–Red and blue LED indicator flash alternately
4：Already connected status— Flashing blue light per 3 seconds
5：Play status—–LED indicator will flashing BLUE intermittently.
6：ANC Status—-ANC ON:LED indicator will long bright green light

Matters attention：

Low battery prompt： prompt： “Battery low”.

This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

FCC ID: 2AJO8-BSBTH30

Specifications:

• Bluetooth version: Bluetooth V5.3

• Chipset: Bluetrum

• Frequency: 2.402-2.480GHz

• Transmission Distance: 10m

• Battery Capacity: 3.7V/200mAH

• Charging Time: about 1.5-2 hours

• Charging Voltage: DC 5V

• Working temperature: -40 to +85

• Playtime ANC ON (100% volume): 6 hours

• Playtime ANC OFF (100% volume): 8 hours

• Standby time: about 300 hours

FAQ:

Q: How do I charge the headphones?

A: Plug the small connector of the charging cable into the charging port on the earcup and the large connector into a USB power source. The LED indicator turns RED during charging and turns OFF when fully charged.

Q: How do I use Active Noise Control (ANC)?

A: Press the [ANC] button to turn on/off Active Noise Control.
ANC reduces unwanted external noise while listening to audio or can be used independently.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>