SALAMANDER DESIGNS FLEXO 100 Medium Tilt Wall Mount Installation Guide
- October 27, 2023
- SALAMANDER DESIGNS
Table of Contents
SALAMANDER DESIGNS FLEXO 100 Medium Tilt Wall Mount
IMPORTANT SAFETY INSTRUCTION
- Carefully inspect the mount for shipping damage or missing parts. If any damage is apparent or you are missing parts contact Salamander Designs at 800-535-5659.
- Read ALL assembly instructions before assembly. If you have any questions, please contact your installation contractor or Salamander Designs.
- Mounts must be attached as specified in assembly instructions. Improper installation can result in serious personal injury.
- This TV mount is intended for use with Flat-Panel TVs 23-42″ with a maximum weight capacity of 100 lbs.
- Use of this mount with products heavier than the maximum weight or larger than the size indicated may result in collapse of the mount causing possible injury.
- The mount is designed to be installed using wall studs or supporting frame. Not for use on steel stud walls or old cinder block walls. Installation to these type of walls will require other fasteners than provided.
- Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
Unpacking
Unpack all content and check to ensure that all of the parts are in proper condition. To help protect the environment, use the appropriate recycling and discarding methods for the packaging items. The boxes used for the packaging of this product may be recycled or re-used.
TOOLS
HARDWARE
PARTS
Install Wall Bracket
**A**
For wood constructions, locate a framing stud at the desired location
using a stud finder device.
**B**
Align and level the Wall Bracket (I) with the framing stud. Using a
pencil mark top and bottom holes as shown.
Note: It is important to utilize one of the three center holes when
installing onto wood framing.
**C**
Predrill mounting holes 2.5” (64 mm) deep using a 3/16” (4.5 mm) bit
for wood construction; 3/8” (10 mm) bit for masonry construction.
D Install Lag Screws (B) with Washers (E), through Wall Bracket (I),
level and tighten firmly with Allen Key (A). For Masonry Installation use
Plastic Wall Plugs (C).
Attach TV Brackets
**A**
Align TV Brackets (II) with FOUR TV mounting holes. Attach using
the supplied Mounting Screws (J). To determine the correct thread size and
length, refer to TV manufacturer installation manual.
NOTE: Washers (D) are necessary when using M4 and M5 mounting screws.
Spacers (F) can be utilized in applications where interferences at back of TV
prevent proper fit of TV Bracket (II).
NOTE: It is always necessary to fasten TV at four points for proper
installation.
**B**
If TV mounting pattern exceeds 13” (330 mm) in width or 8-1/2” (216
mm) in height, use supplied Extension Wings (III) to expand mounting.
Extension Wings (III) are fastened to TV Brackets (II) using Flat Heads (G),
Washers (E), and Hex Nuts (H) prior to mounting to TV.
Attach using the supplied Mounting Screws (J) and optional Spacers (F).
NOTE: It is always necessary to fasten TV at four points for proper
installation.
Install TV to Wall Bracket
**A**
Pull on black cord to unlock Click Fasteners and hook TV Brackets
(II) onto Wall Bracket (I) from top.
B Center TV Brackets (II) on Wall Bracket (I) and push black Click
Fasteners up into lock position.
**C**
Install Pad Lock (IV).
SALAMANDER DESIGNS LIMITED WARRANTY
Salamander Designs Ltd. (Salamander) provides the following Limited Warranty.
The Limited Warranties herein described for the specific products listed below
shall be in lieu of any other warranty, expressed or implied, including but
not limited to any implied warranty of merchantability or fitness for a
particular use.
These Limited Warranties do not cover damages incurred in shipment, failures
caused by other products not supplied by Salamander, or failures due to
accident, misuse, abuse or alteration of the product. Salamander’s sole
liability and the purchaser’s exclusive remedy shall be for the repair, or at
Salamander’s option, for the replacement of the defective part as provided
herein. Notwithstanding the above, if replacement parts for defective
materials are not available, Salamander reserves the right to make reasonable
compensation in lieu of repair or replacement. Liability for incidental or
consequential damages under the warranty is excluded. Some states do not allow
limitation of incidental or consequential damages. Therefore, the above
limitation may not apply in certain instances. Defective product must be given
Return Authorization by Salamander and is to be returned to the factory
prepaid, in the original carton and packing materials. Any damage incurred in
a shipment not in original packing shall be the responsibility of the owner.
Warranty repairs will be returned to the owner prepaid, within the continental
U.S.A. only. This warranty gives you specific legal rights and you may also
have other rights which vary from state to state.
Salamander provides a five (5) year Limited Warranty from the date of the
purchase, on material damage and/or manufacturing defects. Salamander
guarantees that if, during the warranty period, any defects should occur in
the product resulting from faulty material and/or assembly, as assessed by
Salamander, the product will be repaired or, if necessary, replaced free of
charge. The warranty expressly does not apply to normal wear and tear that
becomes apparent after normal use.
During mounting of the product, instructions for the installation and use of
the television must be followed precisely. Correct mounting is essential. For
maximum weights, screen size and correct application, please refer to the
product installation instructions. Failure to comply with these requirements
or the occurrence of any of the following circumstances will result in the
termination of any otherwise applicable Limited Warranty:
a. If the holes in the wall required for the installation of the product
were not drilled in accordance with the instructions for use of the product,
or if the product was not properly installed or used.
b. If you (or third parties) – without Salamander’s or your Salamander
dealer’s prior knowledge and permission – carried out work or repairs on the
product.
c. If a defect is the result of external causes, i.e. in the case of
abnormal types of damage caused by climatological, thermal, mechanical or
other external influences.
d. If the product is not used in accordance with its intended use or if
it is
damaged as a result of negligence.
WARRANTY PROCEDURE
Claims should be made through the dealer from which the product was purchased. The dealer will contact Salamander Designs Ltd. (Salamander) for warranty service. An original sales order number/purchase order number will be required for warranty protection. Salamander’s liability under this warranty is limited to repairing or replacing at Salamander’s option any part or parts of the product found to be defective in material or workmanship within the applicable warranty period. Salamander in its sole discretion will determine the cause and nature of any defect, the necessity and manner of repair or replacement, and all other matters pertaining to the condition of the product.
LABOR AND SHIPPING CHARGES
Should you be entitled to receive a repair or replacement under this warranty, Salamander will pay the cost of labor, handling and shipping to the consumer for two (2) years from the date of purchase by the original consumer. After that date, the purchaser will be responsible for these costs
©2008 Salamander Designs Ltd.
Doc #503-005 v4.08
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>