SALAMANDER DESIGNS Luna Ceiling 200 Projector Installation Guide
- October 27, 2023
- SALAMANDER DESIGNS
Table of Contents
LUNA CEILING 200 PROJECTOR
Installation Manual
IMPORTANT SAFETY INSTRUCTIONS
- Carefully inspect the mount for shipping damage or missing parts. If any damage is apparent or you are missing parts contact Salamander Designs at 800-535-5659.
- Read ALL assembly instructions before assembly. If you have any questions, please contact your installation contractor or Salamander Designs.
- Mounts must be attached as specified in assembly instructions. Improper installation can result in serious personal injury.
- This mount is intended for use with projectors weighing a maximum of 30 lbs.
- Use of this mount with products heavier than the maximum weight or larger than the size indicated may result in collapse of the mount causing possible injury.
- The mount is designed to be installed on a ceiling joist or concrete ceiling.
- Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
Unpacking
Unpack all content and check to ensure that all of the parts are in proper
condition. To help protect the environment, use the appropriate recycling and
discarding methods for the packaging items. The boxes used for the packaging
of this product may be recycled or re-used.
TOOLS
Tools Required for Assembly:
HARDWARE
PARTS
I – 1X – Ceiling Bracket
II – 1X – Mount Hook
III – 1X – Projector Bracket
IV – 4X Projector Arm
Install Wall Bracket
|
---|---
For wood construction applications, locate a ceiling joist at the desired
location using a stud finder device.| For wood construction, mark center of
the 2 holes in the Ceiling Bracket (I) at desired location. Note: It is
important to utilize two holes when installing onto joist.
|
Predrill mounting holes 2” deep using a 11/64” (4.5mm) bit for wood
construction; 5/16” (8mm) bit for masonry construction.| Install 2 Lag Screws
(B) through Ceiling Bracket (I).
For Masonry Installation, use Plastic Plugs (C).
Install Mount to Ceiling Bracket
Screw Mount Hook (II) to Ceiling Bracket (I) by turning clockwise.
Tighten locking screw using Allen Key (A).
Attach Projector to Bracket
Attach three or four Projector Arms (IV) loosely to Projector Bracket (III) using Flange Screws (E) and Washers (D).
|
---|---
Align Bracket Assembly with 3 or 4 projector mounting holes. Attach using the
supplied Mounting Screws (F). To determine the correct thread size and length,
refer to Projector manufacturer’s installation manual. Note: Keep Projector
Bracket hardware aligned front to back and left to right with the projector.|
Tighten screws from step A & B with a screwdriver.
Attach Projector Bracket to Mount Hook
| 
---|---
Set Projector Bracket (III) onto Mount Hook (II).| Lightly tighten screws on
both sides of hooks.
SALAMANDER DESIGNS LIMITED WARRANTY
Salamander Designs Ltd. (Salamander) provides the following Limited Warranty.
The Limited Warranties herein described for the specific products listed below
shall be in lieu of any other warranty, expressed or implied, including but
not limited to any implied warranty of merchantability or fitness for a
particular use. These Limited Warranties do not cover damages incurred in
shipment, failures caused by other products not supplied by Salamander, or
failures due to accident, misuse, abuse or alteration of the product.
Salamander’s sole liability and the purchaser’s exclusive remedy shall be for
the repair, or at Salamander’s option, for the replacement of the defective
part as provided herein. Notwithstanding the above, if replacement parts for
defective materials are not available, Salamander reserves the right to make
reasonable compensation in lieu of repair or replacement. Liability for
incidental or consequential damages under the warranty is excluded. Some
states do not allow limitation of incidental or consequential damages.
Therefore, the above limitation may not apply in certain instances. Defective
product must be given Return Authorization by Salamander and is to be returned
to the factory prepaid, in the original carton and packing materials. Any
damage incurred in a shipment not in original packing shall be the
responsibility of the owner. Warranty repairs will be returned to the owner
prepaid, within the continental U.S.A. only. This warranty gives you specific
legal rights and you may also have other rights which vary from state to
state.
Salamander provides a five (5) year Limited Warranty from the date of the
purchase, on material damage and/or manufacturing defects. Salamander
guarantees that if, during the warranty period, any defects should occur in
the product resulting from faulty material and/or assembly, as assessed by
Salamander, the product will be repaired or, if necessary, replaced free of
charge. The warranty expressly does not apply to normal wear and tear that
becomes apparent after normal use.
During mounting of the product, instructions for the installation and use of
the television must be followed precisely. Correct mounting is essential. For
maximum weights, screen size and correct application, please refer to the
product installation instructions. Failure to comply with these requirements
or the occurrence of any of the following circumstances will result in the
termination of any otherwise applicable Limited Warranty:
a. If the holes in the wall required for the installation of the product were
not drilled in accordance with the instructions for use of the product, or if
the product was not properly installed or used.
b. If you (or third parties) – without Salamander’s or your Salamander
dealer’s prior knowledge and permission – carried out work or repairs on the
product.
c. If a defect is the result of external causes, i.e. in the case of abnormal
types of damage caused by climatological, thermal, mechanical or other
external influences.
d. If the product is not used in accordance with its intended use or if it is
damaged as a result of negligence.
WARRANTY PROCEDURE
Claims should be made through the dealer from which the product was purchased. The dealer will contact Salamander Designs Ltd. (Salamander) for warranty service. An original sales order number/purchase order number will be required for warranty protection. Salamander’s liability under this warranty is limited to repairing or replacing at Salamander’s option any part or parts of the product found to be defective in material or workmanship within the applicable warranty period. Salamander in its sole discretion will determine the cause and nature of any defect, the necessity and manner of repair or replacement, and all other matters pertaining to the condition of the product.
LABOR AND SHIPPING CHARGES
Should you be entitled to receive a repair or replacement under this warranty, Salamander will pay the cost of labor, handling and shipping to the consumer for two (2) years from the date of purchase by the original consumer. After that date, the purchaser will be responsible for these costs.
Adjustments
Rotate projector to proper location and tighten. Tilt projector forward or backward to adjusted angle and tighten. Roll projector left or right to level picture and tighten.
www.SalamanderDesigns.com
©2008 Salamander Designs Ltd. Doc #503-024 v4.08
Documents / Resources
|
SALAMANDER DESIGNS Luna Ceiling 200
Projector
[pdf] Installation Guide
Luna Ceiling 200 Projector, Luna Ceiling 200, Projector
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>