ORCATORCH D500 Portable Magnetic Controlled Dive Light User Manual

ORCATORCH D500 Portable Magnetic Controlled Dive Light

Product Information

Specifications

• Max Lumens: 700
• Output: High – 700 Lumens, Middle – 270 Lumens, Low – 65 Lumens, Strobe – 700 Lumens
• Runtime: High – 1h30min, Middle – 3h40min, Low – 18h10min
• Beam Distance: 235m (on land)
• Intensity Impact Resistant: 13800cd 1m
• Waterproof: Underwater 150m
• Working Voltage: Not specified
• Dimension: 152mm (Length) x 28mm (Diameter) x 45mm (Head)
• Net Weight: 216g (excluding battery)
• Accessories: O-ring, wrist strap, lanyard

Product Features

• Magnetic controlled side switch
• High, Middle, Low, and Strobe modes
• Durable and waterproof design

Technical Parameters (ANSI/NEMA FL1)

• High Mode: Output – 700 Lumens, Runtime – 1h30min, Beam Distance – 235m, Intensity Impact Resistant – 13800cd 1m
• Middle Mode: Output – 270 Lumens, Runtime – 3h40min
• Low Mode: Output – 65 Lumens, Runtime – 18h10min
• Strobe Mode: Output – 700 Lumens

Product Usage Instructions

ON/OFF
Insert the battery and tighten the light head to turn on the flashlight at default low mode. To turn off the flashlight, press the side switch.

Mode Selection
Press the side switch to switch between high, middle, low, and off modes. To access the hidden strobe mode, keep pressing the side switch for 2 to 3 seconds. Press the side switch again to return to the previous mode.

Battery Replacement

1. Insert the battery with the anode side (+) toward the light head.
2. Ensure correct installation of + and – terminals to avoid damage to the flashlight and battery.
3. Use a battery with a voltage that matches the flashlight’s working voltage.
4. Avoid using batteries with damaged surfaces or deformations to prevent short circuit, explosion, leakage, etc.

Usage and Maintenance

• Reason A: The batteries need to be replaced.
  Solution: Replace the batteries, ensuring correct installation of + and – terminals.

• Reason B: The threads, PCB board contact, or other contacts are dirty.
  Solution: Clean the contact points with an alcohol-soaked cotton swab. If the issue persists, please contact the distributors and refer to the warranty policy.

Product Warranty

We offer a warranty for manufacturing defects within 30 days of purchase. If problems develop under normal use, we will repair the light free of charge within 24 months of purchase. After 24 months, we will charge for parts. The total repair fee is determined by the cost of the replaced materials.
Warning
The flashlight emits high-intensity lighting and can cause eye damage. Please avoid shining the light directly into the eyes.

FAQ

• What is the runtime in high mode?
  The runtime in high mode is 1 hour and 30 minutes.

• How deep can the flashlight be used underwater?
  The flashlight is waterproof up to 150 meters underwater.

• What accessories are included with the flashlight?
  The flashlight comes with an O-ring, wrist strap, and lanyard.

PRODUCT INTRODUCTION

ORCATORCH D500 is a portable magnetic controlled flashlight for professional diving use. It is equipped with a totally sealed magnetic controlled side switch that provides flexible operation underwater. Using the latest USA CREE XM-L2(U2) LED, max 700 lumens output and over 18 hours runtime, this portable diving light offers three brightness levels and one strobe mode for different diving environment use. Plus simple style appearance, robust water pressure resistant construction, we believe it will be your best lighting tool for diving.

PRODUCT FEATURES

• Cree XM-L2(U2) LED, max 700 lumens output
• Uses 1*18650 Li-ion battery
• Magnetic controlled side switch, high waterproofness for easy operation underwater
• Water pressure resistant construction ,depth rated to 150 meters
• Standard included wrist strap fastens the flashlight to the back of your hand
• High efficiency constant current circuit, constant brightness
• Reverse polarity protection, to protect from improper battery installation
• Aircraft-grade high strength aluminum material
• Premium Type III military hard-anodized seawater-corrosion-resistance finish
• Alloy aluminum reflector with professional optical analysis
• Toughened glass with high water pressure resistance under deep water

TECHNICAL PARAMETERS

Notice: Stated data has been measured according to the international flashlight test standards ANSI/NEMA FL1 using one ORCATORCH 18650 Li-ion battery(3.7V,2600mAh) under laboratory conditions. The parameters are approximate and may vary between flashlights, batteries, and environments.

OPERATION INSTRUCTIONS

1. ON/OFF: Insert the battery and tighten the light head to turn on the flashlight at default low mode, then you can press the side switch to turn it off.
2. Mode Selection: Press the side switch to switch mode among high, middle, low and off. Keep pressing the side switch for 2 to 3 seconds to get the hidden strobe mode, and press again to get back to the previous mode.

BATTERY REPLACEMENT

1. As shown in the figure, insert the battery with the anode side (+) toward the light head.
2. Please do not reverse the battery to avoid damage to the flashlight and battery.
3. Please do not use battery with higher voltage than the flashlight working voltage.
4. Please do not use battery with damaged surface or deformation to avoid short circuit, explosion, leakage, etc.

USAGE AND MAINTENANCE

• Please keep the flashlight away from high intensity magnetic fields, ²or the switch may fail to function.

• Please clean the surface of the flashlight with fresh water after use in ²case of the seawater corrosiveness.

• Please don’t disassemble the sealed head, doing so may cause ²damage to the flashlight and will void the warranty.

• We recommend the use of high quality batteries. If the flashlight will not be used for a long time, remove the batteries to avoid damage from ²electrolyte leakage or battery explosion.

• Please replace the O-rings if they are damaged after prolonged use and regularly lubricate the o-rings so as to not erode the rubber. Doing ²so will keep the flashlight properly sealed against water.

• Please clean the contacts of your light from time to time, especially when the light flickers or doesn’t light up. There are probably several reasons for a flickering or not working light:

  • Reason A: The batteries need to be replaced.
    Solution: Replace batteries (Please confirm correct installation of + and – terminals).

  • Reason B: The threads, PCB board contact or other contacts are dirty.
    Solution: Clean the contact points with an alcohol soaked cotton swab. If the methods above don’t work, please contact the distributors and refer to the warranty policy.

PRODUCT WARRANTY

We will replace products afflicted with manufacturing defects within 30 days of purchase and repair a light free of charge within 24 months of purchase if problems develop under normal use; if repair is required after 24 months from the date of purchase, we will charge for parts. The total repair fee is dictated by the cost of the replaced materials.
Warning
The flashlight is high intensity lighting device and capable of causing eye damage, please avoid shining the light directly into the eyes.

FOR MORE INFO

ABOUT COMPANY

• ORCATORCH TECHNOLOGY LIMITED
• Tel: +86-755-33560383
• Fax: +86-755-29454989
• Email: info@orcatorch.com
• www.orcatorch.com
• Address: 5th Floor, Emerson Building A, 26 Zone, Baoan District, Shenzhen city, China (518101)

References

• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>