super bright leds LPD-TWR SeriesLPD-TWR24-50 Series Tunable White LED Panel Light User Manual
- June 16, 2024
- super bright leds
Table of Contents
super bright leds LPD-TWR SeriesLPD-TWR24-50 Series Tunable White LED
Panel Light
Product Information
The Tunable White LED Panel Light (LPD-TWR Series) is a recessed ceiling light that provides adjustable color temperature settings. It is designed for easy installation and comes with various accessories for customization.
Specifications
- Model : LPD-TWR Series
- Operating Temperature : Check product label for specific electrical specifications related to installation
- IP Rating : IP20
Safety and Notes
- Please read all instructions prior to installation to ensure safe and proper usage. Disconnect the power supply and remove any existing troffer light or ceiling tile before installing the LED panel light. Make sure to make appropriate electrical connections and follow the recommended installation steps.
- Note that a safety cable is not included but it is recommended to connect one to the grid clip during installation to prevent accidents or injuries.
Recommended Accessories
Optional Suspension Kit (LP-HKO-2)
Optional Accessories
There are no optional accessories mentioned in the user manual.
Product Usage Instructions
Recessed Installation
- Disconnect the power supply and remove any existing troffer light or ceiling tile.
- Make electrical connections.
- Bend out safety tabs to be vertical, then bend the upper portion out 90 degrees.
- Lay the fixture into the T-grid.
Multiple Panel and Dimmer Installation
Included Parts
- 1 – LED Panel Ceiling Light
- 4 – Wire Nuts
Optional Suspension Kit (LP-HKO-2) Installation
- Mount the suspension hardware to the ceiling.
- Hang the panel from suspension cables using a cable clamp to secure it.
Linking Single Controller
Handheld Remote Control
- Hold the ID button (the controller’s indicator light will stay on) and turn the light panel on.
- The light panel will flash to indicate the process is successful, at which point the ID button can be released.
- Hold ID and buttons and turn the light panel on to unlink the remote from the light panel.
Linking Multiple Controllers
If using both the handheld controller and wall-mount controller, the wall
controller can copy some of the functions of the handheld controller by
holding the following buttons simultaneously for a few seconds until the
indicator light turns solid:
| Option Number | Grouping | Handheld Remote | Wall-mount Controller |
|---|---|---|---|
| 1 | 1 | 1 + ID | ON + CCT |
| 2 | 2 | 2 + ID | ON + CCT |
| 3 | 3 | 3 + ID | ON + CCT |
| 4 | 4 | 4 + ID | ON + CCT |
| 5 | All | ID | ON + CCT |
Controllers
The following functions can be performed using the controllers
LPD-TWHR
- COLOR (CCT): 5000K, 4000K, 3500K, 3000K
- BRIGHTNESS : Increases or decreases brightness.
- GROUPING : Selects all linked lights, regardless of group.
- Turn on : The light panel turns on.
- Turn off : The light panel turns off.
- Save : Saves the current color temperature and brightness settings.
LPD-TWWR
- Turn on : The light panel turns on.
- Turn off : The light panel turns off.
- The CCT button cycles between 3000K, 3500K, 4000K, and 5000K color temperature settings.
- Increases or decreases color temperature.
FAQ
-
Q: What is the operating temperature of the LPD-TWR Series?
The operating temperature can be found on the product label. Please refer to it for specific electrical specifications related to installation. -
Q: Are there any optional accessories available for the Tunable White LED Panel Light?
No, there are no optional accessories mentioned in the user manual. -
Q: Is a safety cable included with the product?
No, a safety cable is not included with the product. However, it is recommended to connect one to the grid clip during installation for added safety. -
Q: How do I link multiple controllers?
If using both the handheld remote control and wall-mount controller, you can copy some of the functions of the handheld remote to the wall controller by following the instructions provided in the user manual. -
Q: How do I adjust the color temperature and brightness settings?
The LPD-TWHR controller allows you to adjust the color temperature and brightness settings. Follow the instructions provided in the user manual for detailed steps.
User Manual
LPD-TWR Series
Important : Read all instructions prior to installation.
Tunable White LED Panel Light
Included Parts
- LED Panel Ceiling Light
- Wire Nuts
Safety and Notes
- Product should be installed by a certified electrician in accordance with applicable national, state, and local building and electrical codes.
- To reduce the risk of electric shock, ensure that the main power source and circuit breakers are switched off before performing any installation or wiring procedures.
- Avoid looking directly into the light when illuminated.
- Failure to properly support the fixture may result in damage or injury, for which the manufacturer does not assume responsibility. A safety cable is not included, but it is recommended that one be connected to grid clip during installation.
Recommended Accessories
- Handheld Remote Control (LPD-TWHR)
- Wall-mount Controller (LPD-TWWR)
Optional Accessories
- Optional Suspension Kit (LP-HKO-2)
- Surface Mount Kit (LP-22-SMK for 2×2, LP-24-SMK for 2×4)
Specifications
| Model | LPD-TWRx-x |
|---|---|
| Operating Temperature | -4°–113° F (-20°–45° C) |
| IP Rating | IP20 |
Check product label for specific electrical specifications related to installation. Improper installation will void warranty.
Recessed Installation
- Disconnect supply power and remove existing troffer light or ceiling tile.
- Make electrical connections.
- Bend out safety tabs to be vertical, then bend upper portion out 90 degrees.
- Lay fixture into T-grid.
Optional Suspension Kit (LP-HKO-2) Installation
- Mount suspension hardware to ceiling.
- Hang panel from suspension cables using cable clamp to secure.
Linking Single Controller
Handheld Remote Control
Hold the “ID” button (the controller’s indicator light will stay on) and turn
the light panel on. The light panel will flash to indicate the process is
successful, at which point the “ID” button can be released. Hold “ID” and ▼
buttons and turn the light panel on to unlink the remote from the light panel.
Wall-mount Controller
Hold the “ON” and “OFF” buttons (the controller’s indicator light will stay
on) and turn the light panel on
After the light has been on for 3–5 seconds, release buttons and check to
ensure linking
Linking Multiple Controllers
If using both the handheld controller and wall-mount controller, the wall
controller can copy some of the functions of the hand-hold controller by
holding the following buttons simultaneously for a few seconds until indicator
light turns solid.
Option Number| Grouping| Handheld Remote| Wall-mount
Controller
---|---|---|---
1| 1| 1 + ID| ON + CCT
2| 2| 2 + ID| ON + CCT
3| 3| 3 + ID| ON + CCT
4| 4| 4 + ID| ON + CCT
5| All| ID| ON + CCT
Controllers
| Turn on Turn off
---|---
| Group light(s) by holding the desired group button (1–4) for at least 3
seconds, then turning on the light(s) that should be added to that group. The
light(s) will flash to indicate the group was successfully assigned.
| Selects all linked lights, regardless of group.
| Set the color temperature and brightness to the desired settings to save.
Hold the “SAVE” button for 3–5 seconds until the light goes out. The light
should now use the saved color temperature and brightness when it is powered
on.
| Increases or decreases brightness.
| Increases or decreases color temperature.
| Turn on Turn off
---|---
| Set the color temperature and brightness to the desired settings to save.
Hold the “ON” button for 6–9 seconds until the light goes out. The light
should now use the saved color temperature and brightness when it is powered
on.
| The “CCT” button cycles between 3000K, 3500K, 4000K, and 5000K color
temperature settings.
- Rev Date : V5 04/05/2021
- 4400 Earth City Expy, St. Louis, MO 63045
- 866-590-3533
- superbrightleds.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>