lionelo Hugo i-Size Baby Car Seat User Manual
- June 16, 2024
- lionelo
Table of Contents
- Lionelo Hugo i-Size Baby Car Seat
- Dear customer!
- DEVICE DESCRIPTION (FIG. A)
- INSTALLATION IN THE CAR
- FOLDING OF THE SEAT
- HEADREST ADJUSTMENT
- SEAT INSTALLATION
- SEAT REMOVAL
- REMOVING AND ATTACHING THE COVER
- CLEANING AND MAINTENANCE
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Lionelo Hugo i-Size Baby Car Seat
USER MANUAL
Dear customer!
Should you have any remarks or questions concerning the product, please do not hesitate to contact us: help@lionelo.com
Producer:
Brandline Group Sp. z o. o.
A Kreglewskiego 1, 61-248 Poznan, Poland
For the range of 100 – 150 cm:
Notice: This is a i-Size booster seat Enhanced Child Restraint System. It is approved according to UN Regulation No 129, for use primarily in” i-Size seating positions” as indicated by vehicle manufacturers in the vehicle user’s manual.
If in doubt, consult either the Enhanced Child Restraint System manufacturer or the retailer.
For the range of 135 – 150 cm:
Notice: This is a Universal booster cushion Enhanced Child Restraint System. It is approved according to UN Regulation No 129, for use in i-Size compatible and universal vehicle seating positions as indicated by vehicle manufacturer in the vehicle user’s manual.
If in doubt, consult the Enhanced Child Restraint System manufacturer or the
retailer. The product is only suitable for installation on the locations
marked with symbols 0 in fig. B and marked i-Size.
The seat is designed for forward-facing installation with three-point seat
belts only (fig. B).
WARNINGS:
1. The product is designed for children between 100 – 150 cm tall.
2. Hard parts and plastic parts of the child restraint system should be
placed and installed in such a way that they cannot be trapped by a sliding
seat or vehicle door under normal vehicle operating conditions.
3. Any seat belts that restrain a child must be well-fitted to the child’s
body structure. The belts must not be twisted.
4. The straps securing the restraint to the vehicle must be tight.
5. Make sure the lap belts run low to adequately secure the pelvis.
6. If the product has been exposed to strong elements (such as impact), it
should be replaced.
7. Do not make any changes to the seat or add new components without approval
from the approval authority. To ensure maximum safety for your child, the
equipment should be attached and used as recommended in the instructions.
8. The plastic parts of this seat can heat up in the sun and cause burns on
the child’s skin.
9. Never leave a child alone in a car seat in a vehicle.
10. Luggage and other similar items should be secured so that they will not
cause any injury in a collision situation.
11. Do not use the seat without its fabric cover.
12. The cover cannot be replaced with an item from another set. It is an
integral part of the set and affects the operation of the restraint.
13. Always carry this instruction manual with you.
14. Refer to the vehicle manufacturer’s owner’s instruction manual.
15. The device may not fit all approved vehicles when adjusted for a range
above 135 cm.
DEVICE DESCRIPTION (FIG. A)
1. Headrest
2. Shoulder belt guide
3. Backrest
4. Seat
5. Lap belt guide
6. Headrest adjustment lever
7. ISOFIXarms
INSTALLATION IN THE CAR
FOLDING OF THE SEAT
1. Connect the backrest of the seat to the seat with connectors (see ng. 1).
2. Position the backrest vertically (perpendicular to the seat) (ng. 2).
HEADREST ADJUSTMENT
Pull the headrest adjustment lever and adjust the headrest height (ng. 3). The height of the headrest should be matched to the height of the child, it should be neither too high nor too low (fig. 4). The headrest of the car seat should surround the head. It should not be positioned below (e.g., at neck or shoulder level) or above (e.g., leaving the lower part of the head without any protection). A properly adjusted headrest secures the lower and upper parts of the child’s head, as well as its sides.
SEAT INSTALLATION
Child height: 100- 150 cm
1. Place the car seat on the couch of the car.
2. Press the buttons on the ISOFIX arms and slide them out towards the
attachment points, located in the couch. Push the seat toward them until the
arms tighten and you hear a characteristic click. Tighten the seat by making a
left-right movement toward the backrest to make sure it is pressed as tightly
as possible against the car’s bench seat. The indicator on both ISOFIX arms
must turn green, any other color indicates improper anchoring of the ISOFIX
arms (fig. 5).
Skip the above point if you are not installing the seat using the ISOFIX system.
3. Press the seat against the backrest of the couch.
4. Place the child in the seat and adjust the height of the headrest (see
section: Headrest adjustment).
5. Pass the shoulder belt through the shoulder belt guide (A in ng. 6),
located in the headrest. Pass the lap belt through the lap belt guide under
the armrest. Then pass both belts under the armrest and fasten them (B in ng.
6) while making sure they are not twisted.
Note! Make sure the seat belts are tight, nt tightly around the child’s body and are not twisted. Make sure the lap belts run low and protect the child’s pelvis. The belts should be tight against the child’s body, but should not be too tight and cause discomfort.
Child height: 135- 150 cm
Note! It is recommended to use the car seat with the backrest for as long as possible. 1. Push the backrest of the seat down (ng. 7), then separate the backrest from the seat.
2. Place the base on the couch of the car.
3. Press the buttons on the ISOFIX arms and slide them out towards the
attachment points, located in the couch. Push the seat toward them until the
arms tighten and you hear a characteristic click. Tighten the seat by making a
left-right movement toward the backrest to make sure it is pressed as tightly
as possible against the car’s bench seat. The indicator on both ISOFIX arms
must turn green, any other color indicates improper anchoring of the ISOFIX
arms (fig. 8).
Skip the above point if you are not installing the seat using the ISOFIX system.
4. Press the seat against the backrest of the couch.
5. Place the child in the seat.
6. Pass the lap belt through both lap belt guides under the armrests. Fasten
the belts while making sure they are not twisted and the shoulder belt runs
over the armrest (fig. 9).
Note! Make sure the seat belts are tight, fit tightly around the child’s body and are not twisted. Make sure the lap belts run low and protect the child’s pelvis. The belts should be tight against the child’s body, but should not be too tight and cause discomfort.
SEAT REMOVAL
Unbuckle the car seat belt. If the seat was also installed using the ISOFIX system, press the buttons on both ISOFIX arms and slide them out of the attachment points (fig. 10).
REMOVING AND ATTACHING THE COVER
1. Push the backrest of the seat down (fig. 7), then separate the backrest
from the seat.
2. Unfasten the snaps in the fabric, located at the bottom of the backrest,
and remove the cover. Slide them off the headrest as well (fig. 11).
3. Unfasten the snaps, located under the seat (fig. 12), and slide off the
cover.
To reattach the cover, follow the above steps in reverse order.
CLEANING AND MAINTENANCE
Plastic parts can be cleaned with a damp cloth and mild detergent. Do not use
strong detergents or bleaching agents. The cover can be machine washed at
30°C.
The photos are for reference only, the actual look of the products may differ
from the ones shown in the pictures.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>