GENAI J01 Wireless Earphones User Guide
- June 15, 2024
- GENAI
Table of Contents
GENAI J01 Wireless Earphones
Product Overview
- The headset MFB key
- Headphone indicator light
- Earphone charging contact
- Loudspeaker sound hole
- Charging bin indicator
- Type-C Charging port
Power On/Off
Power on: Power on: Turn on the earphones on both sides of the lid of the charging box to automatically power on and enter the group pairing state, the and white lights flash for 200ms, and then turn off after connection, and issue “Power on” or “Power on”(manual power on) and long press the MFB touch key for about 3 seconds.
Shutdown: Put the earphone into the charging compartment under the cover and enter the charging state, The earphone will automatically shut down and disconnect. The and white light will flash for 3 times and then go off.
Bluetooth Pairing
- Open the charging chamber, take out the headset and start it automatically; Please connect the Bluetooth headset with the mobile phone (or other connecting devices)The distance is within 50CM, the closer the better.
- 0pen the Bluetooth interface of the mobile phone, Search and link the Bluetooth name “J01”, click Pairing, and the and white light will flash for 200ms.After pairing is complete, the left ear light will turn off, and the right ear and white light will flash quickly. After connecting the mobilephone successfully, the light will turn off， and send “Pairing successful or” Successful”;
LED Indication Status
- Pairing status: White lights flash alternately
- Voice switching status: white light flashing
- Music status: No light.
- Earphone charging status: white light flashing
- Earphone charging complete: white light is solid
- Earbuds out of the charging case: The headphones flash white
- Headphone reset: After successful reset, the headphone white light is always on
Product Operating Instructions
Boot| Open the charging compartment (or lift the headphones and place them in
the charging case),The headset turns on automatically. Long press the headset
touch key 2S, Power on manually
---|---
Shutdown| Put the earbuds back into the charging case, close the lid of the
charging compartment, and the earbuds are automatic Disconnects and goes to
sleep. Long press the headset touch key 5S,Manual shutdown.
Volume up and down| Three hits on the right to add, and three hits to the left
to subtract.
Up and down| Double-click on the left for the previous song Double-click on
the right for the next song.
Play/pause dialing| Click
Answer the phone| Click when a call comes in
Reject the call| Press and hold the call duration for two seconds
Sini features| Press and hold for 2 seconds and beep
Headset pairing| Headsets are automatically paired out of the warehouse
Specifications
- P The name of the match: J01
- Bluetooth version: V5.3
- Battery capacity of headset: 50mAh
- Battery capacity of charging box: 400mAh
- Bluetooth effective distance: 10m
- Operating voltage: 3-4.2V
Matters Needing Attention
- Do not use abrasive cleaners to clean this product.
- Do not allow this product to be heated or close to a fire source, such as a cooking stove.
- Do not expose the product to direct sunlight for a long time.
- Do not discard this product in fire to avoid explosion.
- Do not attempt to disassemble this product to make any modifications, as it does not contain any maintenance components.
- Do not use this product in rain.
- If you do not plan to use this product for a long time, please store it in a dry environment and Charge the headset less once to prolong its life and avoid extreme temperature and dust.
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular
installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Note: The Grantee is not responsible for any changes or modifications not
expressly approved by the party responsible for compliance. such modifications
could void the user’s authority to operate the equipment.
The device has been evaluated to meet general RF exposure requirement.
This equipment complies with FCC’s RF radiation exposure limits set forth for
an uncontrolled environment. This device and its antenna(s) must not be co-
located or conjunction with any other antenna or transmitter.
Label:
FCC ID:2A27V-J01
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>