eLinkSmart 904Z Keyless Entry Door Lock Deadbolt Instruction Manual
- June 15, 2024
- eLinkSmart
Table of Contents
eLinkSmart 904Z Keyless Entry Door Lock Deadbolt
Product Information
Specifications
- Model: 904Z / 905Z / 906Z / 907Z
- Material: Aluminum Alloy+PC+Silicagel
- Available thickness: 35mm ~ 50mm
- Unlock way: Fingerprint/Password/Key
- Power supply: 4*AA alkaline batterys
- Emergency Supply: USB(Type-C Interface)
- Working voltage: 6V
- Alarm voltage: 4.8V
- Code capacity: Master code:10 sets, User code:40 sets, One-time code:10 sets
Parts List
- Exterior Assembly x 1
- Mounting Plate x 1
- Interior Assembly x 1
- Deadbolt x 1
- Striking Plate x 1
- Hole Aligning Device x 1
- Key x 2
- Reset-Pin x 1
- Pan Head Screw x 2
- Screw x 3
- Self-Tapping Screw x 4
Installation Instructions
- According to the template, drill a hole in the door and adjust the size of the door frame according to your needs.
- Put the deadbolt into the hole on the door.
- Turn the follower and keep the latch bolt out. Fix it on the door with two self-tapping screws.
- Turn and keep the spindle in a vertical position. Make sure the latch bolt is fully retracted (in the unlocked position) before installation.
- Insert the Exterior Assembly into the door hole. Route the cable below the latch.
- Wear the cable into the square hole of the mounting plate.
- Fix the mounting plate on the door with two pan head screws.
- Turn the knob left or right based on the position of the latch bolt. If the latch bolt is on the left, rotate the knob to the left as shown.
- Connect the cable and ensure the connection is tight.
- Fix the Interior Assembly on the mounting plate with three screws.
- Install 4 AA alkaline batteries.
- Install the battery box.
- Turn the knob to test locking and unlocking. Check for completion.
- Twist the back knob manually to extend the lock bolt and keep it extended. Refer to the following settings to set the locking direction.
Frequently Asked Questions (FAQ)
How do I change my master code?
To change your master code, follow these steps:
- Enter your current master code using the keypad.
- Press the * button.
- Enter your new master code using the keypad.
- Press the # button to confirm.
Can I use multiple fingerprints for unlocking?
Yes, you can register multiple fingerprints for unlocking. Follow the
instructions in the user manual to add additional fingerprints to the lock
system.
Details
Parameters
-
Model : 904Z / 905Z / 906Z / 907Z
-
Material : Aluminum Alloy+PC+Silicagel
-
Available thickness : 35mm ~ 50mm
-
Unlock way: Fingerprint/Password/Key
-
Power supply: 4*AA alkaline batterys
-
Emergency Supply: USB(Type-C Interface)
-
Working voltage : 6V
-
Alarm voltage : 4.8V
-
Code capacity:
- Master code :10 sets
- User code: 40 sets
- One-time code: 10 sets
Parts list
Installation
- According to the template, hole in the door and door frame.
- According to the demand, adjust the size of the deadbolt.
- Put the deadbolt into the hole digged on the door. Fix it on the door with two self-tapping screws.
- Turn the follower and keep the latch bolt out.
- Turn and keep the spindle in a vertical. Please make sure the latch bolt is fully retracted (in the unlocked position) before installation
- Insert the Exterior Assembly into the door hole. Route the cable below the latch.
- Wear the cable into the square hole of the mounting plate.
- Fix the mounting plate on the door with two pan head screws.
- Turn the knob left or right base on the position of the latch bolt .
- If the latch bolt is on the left, rotating knob to the left as shown .
- Connect the cable and ensure connection is tight.
- Fix the Interior Assembly on the mounting plate with three screws .
- Install 4 pcs AA alkaline battery.
- Install the battery box.
- Turn the knob to test lock and unlock.Check the completion.
- Twist the back knob manually to extend the lock bolt and keep it extended. Refer to the following settings to set the locking
Read User Manual Online (PDF format)
Loading......