eLinkSmart 904Z Keyless Deadbolt Lock User Manual

eLinkSmart 904Z Keyless Deadbolt Lock

Specifications

• Model: 904Z / 905Z / 906Z / 907Z
• Material: Aluminum Alloy+PC+Silicagel
• Available thickness: 35mm ~ 50mm
• Unlock way: Fingerprint/Password/Key
• Power supply: 4*AA alkaline batteries
• Emergency Supply: USB(Type-C Interface)
• Working voltage: 6V
• Alarm voltage: 4.8V
• Code capacity: Master code:10 sets User code:40 sets One-time code:10 sets

Parts List

• Exterior Assembly x 1
• Mounting Plate x 1
• Interior Assembly x 1
• Deadbolt x 1
• Striking Plate x 1
• Hole Aligning Device x 1
• Key x 2
• Reset-Pin x 1
• Pan Head Screw x 2
• Screw x 3
• Self-Tapping Screw x 4

Installation

1. According to the template, create a hole in the door and adjust the size of the door frame according to the demand.
2. Put the deadbolt into the hole dug on the door.
3. Turn the follower and keep the latch bolt out. Fix it on the door with two self-tapping screws.
4. Turn and keep the spindle in a vertical position. Ensure that the latch bolt is fully retracted (in the unlocked position) before installation.
5. Insert the Exterior Assembly into the door hole. Route the cable below the latch.
6. Wear the cable into the square hole of the mounting plate.
7. Fix the mounting plate on the door with two pan head screws.
8. Turn the knob left or right based on the position of the latch bolt.
9. If the latch bolt is on the left, rotate the knob to the left.
10. Connect the cable and ensure the connection is tight.
11. Fix the Interior Assembly on the mounting plate with three screws.
12. Install 4 AA alkaline batteries.
13. Install the battery box.
14. Turn the knob to test lock and unlock. Check for completion.
15. Twist the back knob manually to extend the lock bolt and keep it extended. Refer to the following settings to set the locking direction.

Set Up

After the installation is completed, it is necessary to correct the locking direction of the door lock through the Self-test Function of the device:

1. Keep the door open, twist the back knob manually to extend the lock bolt and keep it extended.
2. Press the key + + 9 + , and the device will automatically adjust the locking direction.
3. After the adjustment is completed, the lock bolt will automatically retract and become the unlocked state. If not, repeat the above operation.
4. If the device enters the user, it needs to verify the master code or fingerprint before performing the Self-test Function.

Note:

• The master code is 123456 under factory default conditions.
  After adding a master, the default code becomes invalid.

• If there is no master, the default code has administrator privileges.

• Users can set a 6-8-digit code.

• Users can prevent the code from being exposed to strangers by entering random numbers before and after the code, and the number of digits does not exceed 40.

• The key has the function of locking and returning, and the key has the function of unlocking and confirming. Users can also unlock and lock by verifying fingerprint.

• If you enter the wrong code or fingerprint 5 times in a row, the system will be locked for 3 minutes.

FAQ

Q: How many sets of codes can be stored?

A: The lock can store up to 10 sets of master codes, 40 sets of user codes, and 10 sets of one-time codes.

Q: What is the default master code?

A: The default master code is 123456. However, after adding a master code, the default code becomes invalid.

Q: How can I prevent my code from being exposed to strangers?

A: You can enter random numbers before and after your code to prevent it from being exposed. The number of digits should not exceed 40.

Q: What happens if I enter the wrong code or fingerprint multiple times?

A: If you enter the wrong code or fingerprint 5 times in a row, the system will be locked for 3 minutes.

Details

Parameters

• Model:
  904Z / 905Z / 906Z / 907Z

• Material:
  Aluminum Alloy+PC+Silicagel

• Available thickness:
  35mm ~ 50mm

• Unlock way:
  Fingerprint/Password/Key

• Power supply:
  4*AA alkaline batterys

• Emergency Supply:

• USB(Type-C Interface)
  Working voltage: 6V
  Alarm voltage : 4.8V

• Code capacity:
  Master code:10 sets
  User code:40 sets
  One-time code:10 sets

Parts list

Installation

5.Set up

After the installation is completed, it is necessary to correct the locking direction of the door lock through the “Self-test Function” of the device:

1. Keep the door open, twist the back knob manually to extend the lock bolt and keep it extended.
2. Press the key , and the device will automatically adjust the locking direction.
3. After the adjustment is completed, the lock bolt will automatically retract and become the unlocked state, otherwise perform the above operation again.
4. If the device enters the user, it needs to verify the master code or fingerprint before performing the “Self-test Function” .

Note:

1. The master code is “ 123456 ” under factory default conditions. After adding master, the default code becomes invalid.
2. If there is no master, the default code has administrator privileges.
3. Users can set a 6-8-digit code.
4. Users can prevent the code from being exposed to strangers by entering random numbers before and after the code, and the number of digits does not exceed 40.
5. The key has function of locking and returning , and the key has the function of unlocking and confirming. Users can also unlock and lock by verifying fingerprint.
6. If you enter the wrong code or fingerprint 5 times in a row, the system will be locked for 3 minutes.
   This state can be released after the time is up or the power is cut off.

Instructions(press or timeout to exit)

Add master code or fingerprint:

1. Press .
   ( Need to enter a master code before enter fingerprints)

2. Verify the master code confirm or verify the master fingerprint.

3. Enter the master code twice in a row or enter fingerprint 5 times.

4. 10 master codes or fingerprint can be added, and the location number range is 001-010.

5. The location number of the first master code or fingerprint added is 001 and so on.

Add user code or fingerprint:

1. Press .
2. Verify the master code confirm or verify the master fingerprint.
3. Enter the user code twice in a row or enter fingerprint 5 times.
4. 40 user codes or fingerprint can be added, and the location number range is 011-040.
5. The location number of the first user code or fingerprint added is 011 and so on.

Add a one-time code:

1. Press .
2. Verify the master code confirm or verify the master fingerprint.
3. Enter the one-time code twice in a row.
4. The one-time code can only open the lock once, and the code will be automatically invalidated and deleted after use.
5. 10 one-time codes can be added.

Delete user code (There are three ways):

1. Press .

2. Verify the master code + confirm or verify the master fingerprint.

3. Enter the unneeded code or fingerprint .

4. Enter the location number of the unneeded code or fingerprint .
   (For example, 002 represents the second master code, 012 represents the second user code)

5. Enter “0000” to delete all user codes or fingerprint except the master code or fingerprint.

6. Master code or fingerprint need to be kept at least one.

7. The newly added code and fingerprint will be filled to the front position.

Vacation mode:

1. Press .
2. Verify the master code confirm or verify the master fingerprint.
3. When vacation mode is enabled, no user code or fingerprint other than the master will be able to
   open the door until the mode is disabled.

Silent mode:

1. Press .
2. Verify the master code confirm or verify the master fingerprint.
3. Enable and disable silent mode.

Delayed auto-lock function:

1. Press .
2. Verify the master code + “ ” confirm or verify the master fingerprint.
3. Enter the delay auto-lock time .
4. The time can be set for 5-30 seconds / input “0” to disable the delay automatic locking function.

Self-test Function:

1. Keep the door open, twist the back knob manually to extend the lock tongue and keep it extended.
   Press the , and the device will automatically adjust the opening direction.

2. Verify the master code confirm or verify the master fingerprint.

3. After the adjustment is completed, the lock tongue will automatically retract and become the unlocked state, otherwise perform the above operation again.

4. When the device cannot be used normally, it can be adjusted to the normal state through the “Self-test Function” .

Restore to factory default settings:

Method 1:

1. Press and hold the reset button 5 seconds through the “ Reset-PIN ” until a long beep is heard.
2. Release the reset button.
3. The factory default settings are restored successfully.

Method 2:

1. Press .
2. Verify the master code confirm or verify the master fingerprint.
3. The factory default settings are restored successfully.

Functions

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>