lionelo 5903771700061 Sven Plus 2 in 1 Baby Bed User Manual

: June 15, 2024
: lionelo

Table of Contents

5903771700061 Sven Plus 2 in 1 Baby Bed
Preface
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY
Safe use of batteries
Assembly instruction
Cleaning
Warranty conditions:
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Sven Plus Travel bed
User Manual
Warranty card

5903771700061 Sven Plus 2 in 1 Baby Bed

www.lionelo.com

lionelo 5903771700061 Sven Plus 2 in 1 Baby Bed - Figure
1

Preface

Dear Customer!
Thank you for placing your trust in us and choosing Lionelo.
Our products are made with the utmost care to ensure comfort and above all, maximum safety of your child. Implementation of high quality materials and modern technologies allows us to provide users with a product that is perfectly suited for everyday use.

IMPORTANT!
STOP THESE INSTRUCTIONS FOR FUTURE USE.
In case of any questions or comments on the purchased product, please contact us: pomoctechniczna@lionelo.com

Note: The assembly of the product must be performed by an adult.
Failure to comply with this provision and the assembly instructions could result in serious injury or even death.
Producer:
BrandLine Group Sp. z 0. o.
ul. A. Kreglewskiego 1, 61-248 Poznan, Poland

IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY

WARNINGS

Be aware of the risk of open fire and other sources of strong heat, such as electric bar fires, gas fires, etc. in the near vicinity of the cot.
Do not use the cot if any part is broken, torn or missing and use only spare parts approved by the manufacturer.
Do not leave anything in the cot or place the cot close to another product, which could provide a foothold or present a danger of suffocation or strangulation, e.g. strings, blind/ curtain cords.
Donot use more than one mattress in the cot.
The cot is ready for use only when the locking mechanisms are on. Before use, carefully check that these mechanisms are fully switched on.
The lowest position of the cot is the safest and should always be used as soon as the child starts to sit up.
The upper position of the cot is suitable for children weighing up to 9 kg. If your child starts to sit down himself, use only the lower position.
If you leave the child unattended in the crib, always make sure that the side entrance is fastened with a zipper.
Before replacing the base with the lowest one, it is necessary to remove the support rails.
All mounting elements should always be tight, connections should be regularly checked and tightened if necessary.
The cot can not be used by children who can get out of it the mselves, it may cause a fall and serious injuries or even death.
WARNING – Only use the mattress sold with this cot, do not add a second mattress on this one, suffocation hazards.
The mattress is an integral part of the bed.

lionelo 5903771700061 Sven Plus 2 in 1 Baby Bed - integral
Part

CHANGING PAD WARNING – Do not leave your child unattended.

Thebaby cots should be blocked before using the changing table.
The changing table is suitable for children up to 12 months of age and weighing up to 11 kg.
Any additional or replacement parts can only be obtained from the manufacturer.
Donotuse the changing unit if any part is broken, tom or missing.
Be aware of the risk of open fires and other sources of strong heat, such as electric bar fires, gas fires etc. in the near vicinity of the changing unit.
All mounting elements should always be tightened, joints should be checked regularly and tightened if necessary.

Safe use of batteries

Batteries should not be charged.
Batteries should only be charged under adult supervision.
Batteries must be removed from the toy before charging.
Do not insert different types of batteries or new and used batteries.
Insert batteries with the correct polarity.
Exhausted batteries should be removed from the toy.
Shorting clamps should not be shorted.
To replace the batteries: use a screwdriver to open the door and access the battery compartment.
Replace the batteries and make sure they are inserted gua correctly. Screw the door with a screwdriver.
The toy cannot be connected to more power sources than recommended.

Assembly instruction

Take the travel baby bed out of the bag and loosen the adhesive straps. Place the bed on the floor and put the bag aside (see fig. 1).
Separate the legs pulling them apart. Keep the central lock up.
Otherwise handrails will not fit in the right place (see fig. 2).
Note! So that the sides of the cot / handrails are properly blocked, the central blockade of the floor must be raised upwards. The baby rails will not lock when the floor is unfolded.
Pull the middle part of each top rail covered with material so that they fit into place. Start with the longer rails, and then the shorter ones (see fig. 3).
Push the middle lock until the surface is completely flat (you will hear the click sound) (see fig. 4).
Place the mattress in the baby bed (see fig. 5, 6).
Fasten the mattress using Velcro on the two short sides of the mattress (there are special openings in the floor for fastening).
Base installation
The base must be attached using the zipper. Once the base is attached, cover the zipper with a Velcro pad. Slide the reinforcement tubes into the sewn handles and connect them (they must be paired properly). Place the mattress onto the tube-reinforced base and fasten it with Velcro.
Canopy installation
Slide the plastic arches into the material guide of the canopy and connect them in the middle. Place the rear part of the canopy on the baby bed, then stretch the fabric and attach the canopy to the baby bed using plastic clamp holders.
After the roof has been mounted, it should be pressed several times parokrotniefrom the top to get rid of the pointed shape, which is picked up in the carton (see fig. 7, 8).
Changing table assembly instruction
Slide the stiffening tubes into the cloth rewinders. Combine them with additional pipes with plastic fasteners. Fasten the material with all the naps, pull it firmly on the resulting frame. Insert the plastic fastening elements on the longer sides of the cot, insert additional fasteners in the shorter side of the bed. Fasten the organizer’s naps on dedicated places on the bed frame, stretching the organizer’s material at the changing table (see fig. 9).
Organizer installation
Put the hooks on the organizer and mount it on the bed frame (see Fig. 11a, 11b).
Baby bed folding instruction
Remove all the bed accessories. Remove the mattress, Canopy, organizer and all the other accessories. Grasp the centre handle located in the middle of the floor and pull it up (see fig. 12).
To unlock the upper rails, press the indicated buttons on each side of them. Pull it slightly up and then push it down. Unlock the shorter sides first, and then do the same with the longer ones.
While still pulling up the handle, lift the floor of the baby bed and fold the legs (see fig. 13).
Wrap the folded bed with the mattress and fasten it with Velcro straps. Put the folded baby bed into the bag (see fig 14, 15.).If the installation is unsuccessful, repeat the whole process again until submission

Cleaning

Wipe the product with a damp cloth, then allow to dry.
Changing table – clean with warm water and mild soap. Do not dry clean and do not use caustic agents. Do not dry mechanically, do not iron.

The product has been tested and meets all the requirements of the:
EN 716-1:2017+AC:2019
EN 12221-1:2008+A1:2013

Interactive dog:

This product complies with the requirements of the Toy Safety Directive (2009/48 / EC), therefore the CE mark has been affixed and a declaration of compliance with European standards has been issued.
The pictures in this manual are for illustrative purposes only.
Therefore, they may differ from the actual product.

BrandLine Group Sp. z o. o.
ul. A. Kreglewskiego 1
61-248 Poznan, Poland
www.lionelo.com

WARRANTY CARD

Model: ————
SN: ————–

May be sold in:
BE CZ DK DE EEIE EL ES FR HRIT LVLT HU MT NLAT PL PT RO SI SK FI SE UK

Warranty conditions:

The Lionelo brand with its registered office at A. Kreglewskiego 1, 61-248 Poznan, Poland guarantees that the equipment is operational in accordance with the technical-operating conditions described in the manual.
The warranty is granted for a 60 months period from the date of sale. If the Buyer is a company (VAT invoice), the warranty is granted for a 12-month period.
The warranty is valid in the country of purchase.
Revealed manufacturing defects shall be removed during the warranty period free of charge by the Authorised Manufacturer Service.
Any defects or damages discovered and reported within the warranty period will be removed free of charge within 21 working days, but in justifiable cases (for instance, spare parts must be brought from abroad) this period may be extended by another 30 days.
Any defects or damages to the equipment should be reported and delivered to the service site immediately after being revealed.
Accessories included with the devices are under 3-month warranty from the date of purchase.
In case of an unjustified complaint (a complaint of efficient product or the mechanically damaged one), the person who reports a complaint shall be charged for transportation cost.
The Customer is entitled to replacement of the product to another with the same or similar specifications (and) colours if the Service determines that the removal of defects is not possible.
The service is not responsible for any loss of data.
The warranty will be respected only if the customer attaches (to the faulty device) a damage description, all of the accessories received at the moment of the equipment purchase, and proof of purchase containing the date of sale.
The warranty does not cover: natural wear of the product related to its normal operation, damage resulted from improper usage or non-compliance of the instructions described in the manual, tears or cracks caused by the Customer, fading of fabric resulting from prolonged exposure to sunlight or washing the product or its parts in the wrong temperature, mechanical, electrical, thermal and intentional damages and defects caused by them, as well as damage caused by unauthorised modifications or repairs.
The Service may refuse to repair products in case of any traces of unauthorised repair.
If the fault is not covered by the manufacturer’s warranty, paid repair may be offered by the Service.
Neither the Manufacturer nor the Authorised Service is responsible for any damages or losses arising from the inability to use the device that is being repaired.
The product that has not been collected from the service site within 3 months can be charged with storage cost appropriate to the storage time.
Delivery of the product which is incomplete or lack of proper packaging is equivalent to the failure of the warranty conditions by the Buyer, and it can provide a basis to refusal of the repair or extension of the repair period.
In case of sending the product for repair, when no defect is found, the expenses for the expert assessment shall be fully borne by the consumer.
If the product (sent for repair) works properly, and the reason of its invalid operation is, for instance, a low battery, the Consumer shall bear the cost of the expert assessment.
The product warranty shall not exclude, limit or suspend the Customer rights resulting from the guarantee.
Only clean products in original or replacement packagings can be reclaimed.