VSYSTO V7S Truck Dash Camera User Manual

VSYSTO V7S Truck Dash Camera User Manual

Safety Instructions

In order to use this product safely, please confirm that you fully understand the following.
WARNING: This section indicates that mishandling can have serious consequences.
Note: This section indicates that improper handling may cause injury to the user or damage the product.

Prohibit

Obey

WARNING

Please use this product under the premise of obeying traffic rules.
Do not install the device in a position that blocks the view or obstructs driving.
Do not disassemble or modify this product by yourself.
Do not use accessories not included.
Do not allow water to enter this product.

ATTENTION

If the product makes an abnormal noise or smell,please stop using it immediately.
The waterproof rating of the camera is IP67, and the host is not waterproof.
When disposing of this product, please follow the classification principle and do not discard it at will.
Do not store this product in a high temperature and humid environment.

Features

Replace conventional lithium batteries with super capacitors for longer life and safer

1. HD display screen.
2. Support reversing auxiliary line.
3. Support battery voltage display.
4. Infrared night vision camera.
5. Video can be recorded after inserting Micro SD card.

Standard Accessories

• Host

• Camera

• User Manual

• Power Cable
  

If there is any change of specification and appearance due to improvement, we are not able to inform you in advance. Please understand.
Please note that there are differences between the schematic diagram and the real object in the manual.

Description of Each Part

1. Up Button
2. OK Button
3. Down Button
4. Card Slot
5. Reset Button
6. Microphone
7. Camera Connector
8. Power Connector
9. Power Cable
10. Camera

Micro SD Card

1. Please use the high-quality Class10 or above genuine SD card;
2. The recorder supports 16G-256G memory card;
3. If the memory card cannot save the file properly, please format it on the recorder.

Formatting will delete the data, please backup the card data before performing formatting.

1. Insert the card into the card slot as shown in the picture.
2. When picking up the card, gently press the SD card and slowly release it after hearing “Da”.
3. Please pay attention to the direction of the gold finger on the SD card.

If it is inserted reversely, the SD card and recorder will be damaged.

Attention:

1. The card used on other devices will be automatically formatted after being inserted into our DVR. Please back up the data.
2. In the case of high frequency of use, it is recommended to format the memory card every two weeks.
3. Please do not pull out the card in the recording state to avoid damaging the video file and recorder.

Specifications

Installation Guide

Please connect the yellow wire on the rear camera to the 12V positive pole of the inverted light. When the vehicle is in reverse gear, the rear camera screen will be displayed in full screen on the main unit of the recorder, with a reversing auxiliary line. It is convenient for users to observe the surrounding environment when reversing.

Host Fixed Installation Diagram:

1. Hang it on the windshield.
2. Stand on the center console.

Note: You can choose to rotate 180° to adjust the screen interface in the host menu.

Power on

After installing the recorder and inserting the SD card, insert the charger into the cigarette lighter. Start the car to start recording automatically

Attention
This recorder uses the latest supercapacitor design to replace the traditional lithium battery design, supercapacitor will automatically charge and can save the last file after disconnecting the power.

Time Setting

Pause recording after the recorder is turned on→Enter Menu→Choose time setting→Press↑↓to adjust time→Press ok to save the settings

Manually Trigger Lock Video

In the recording state, long press the up button, the recorder will enter the emergency lock mo de, record a locked video and capture a photo of the rear camera at the same time. The video file name is named after KEY-XXXXX. The locked video will not be overwritte n by the normal recorded “REC-XXXXX” file. When the SD card video file exceeds 10 KEY-XXXXX videos, the system will delete the earliest KEY-XXXXX emergency video. G-sensor trigger lock video
In the recording state, if the G-sensor sensitivity is turned on, the video will be locked after the G-sensor is triggered by a collision and reaches the system preset level. And the locked video will not be overwritten by the normal recorded “REC-XXXXX”. The name of the locked video file is GSR-XXXXX. When the SD card video file exceeds 10 GSR-XXXXX videos,the system will delete the earliest emergency video of GSRXXXXX.

Recording Mode

Please format the SD card before inserting it. After inserting the SD card, turn on the power of the motorcycle, and the recorder starts to enter the normal loop recording mode. You can set 1/2/3/5 minutes to save a video in the menu. When the SD card is full, new video files will overwrite the oldest saved files. To prevent loss of important files, please backup important video files in time.

Playback Video Mode

In the recording state of the recorder, short press the OK button to pause the recording. Then long press the OK button, the recorder enters the system setting interface, use the up/down button to select the video to be played, and then short press the OK button to enter the playback mode. If you need to exit the playback mode, long press the OK button to return to the system setting interface. Then use the up/down button to select the recording icon, and then short press the OK button again to successfully return to the recording mode.

Screen Information and Menu Descriptions

1. After selecting, press OK o enter recording mode.
2. The icon becomes larger to indicate that the function has been selected.

Description of characters on the display in recording mode:

1. After selecting, press OK o enter playback mode.

2. The icon becomes larger to indicate that the function has been selected.

3. Press to select the video to playback “R/” indicates rear camera video playback Reversing auxiliary line.
   

4. After selecting, press to enter setting mode.

5. The icon becomes larger to indicate that the function has been selected.

1min/3min
10.Protection Level| G-Sensor  sensitivity  level  adjustment
11.System reset| Restore to the factory default settings
12.Format SD card| Delete all videos from the memory card
13.FW version| Information about the current software version of the recorder

1. After selecting, press to enter language selection mode.

2. The icon becomes larger to indicate that the function has been selected.

3. Language identification — corresponding to the selected language.

4. The number of language options depends on the actual model.

The specific functions are subject to the actual product received.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>