SIM-LAB 75-100 VARIO Triple Monitor Mount Instruction Manual
- June 14, 2024
- SIM-LAB
Table of Contents
SIM-LAB 75-100 VARIO Triple Monitor Mount
BEFORE YOU START
Thank you for purchasing this Sim-Lab product! On the following pages, you
will find detailed instructions on assembly. This requires only a set of
simple tools and some of your time. Please check the bill of materials before
starting (page 13) and make sure all the parts are delivered.
This product combines some products we normally offer separately. In some
cases there are slight changes in the assembly instructions in this manual
versus what the products’ own manual states.
We encourage you to read the product manuals for included products if this one
doesn’t answer all of your questions.
Please refer to the following if needed:
www.sim-lab.eu/xero-play-pivots-manual
www.sim-lab.eu/vario-vesa-manual
Inserting Slot-Nuts:
You got excited, finished the build, put the caps on, but forgot to install
one element. Do not worry. It happens to everyone. In this diagram, you can
see how to insert a Slot-Nut directly into the slot from the side.
You can also use one of your smaller Hex wrenches to help wiggle the Slot-Nut
in place.
Tools needed
Installation Instruction
BOX A – VARIO TRIPLE MONITOR MOUNT PROFILE KIT
#| Part| QTY| Note
P1| 80X40 Length=1195mm| 1|
P2| 80X40 3N Length=1195mm| 1| Left upright, engraved.
P3| 80X40 3N Length=1195mm| 1| Right upright, engraved.
P4| 80X40 3N Length=580mm| 1| Left arm, engraved.
P5| 80X40 3N Length=580mm| 1| Right arm, engraved.
P6| 40X40 Length=580mm| 2|
HARDWARE KIT
A7| VESA 100/200 adapter (optional)| 4| Depends on purchase.
A8| Rubber foot| 4|
A9| Triple sandwich plate 80| 2|
A10| Corner bracket 40×40| 4|
A11| Corner bracket 40×40 cap| 4|
A12| Profile 80×40 end-cap| 8|
A13| Profile 40×40 end-cap| 4|
A14| Bolt M8 X 25 DIN 912| 4|
A15| Bolt M8 X 20 DIN 912| 8|
A16| Bolt M8 X 16 DIN 912| 8|
A17| Bolt M8 X 20 DIN 7380| 4| Buttonhead.
A18| Cap-Washer M8| 10|
A19| Washer M8 DIN 125-A| 8|
A20| Washer M8 DIN 988| 4|
A21| Slot-Nut M8| 24|
Disclaimer: for some entries on this page, we supply more than required as
spare materials. Don’t worry if you have some leftovers, this is intentional.
BOX B – Xero-Play triple pivot set HARDWARE KIT
#| Part| QTY| Note
B1| Xero-Play triple pivot adapter| 8|
B2| Bolt M8 X 40 DIN 912| 4|
B3| Bolt M8 X 25 DIN 912| 16|
B4| Nut M8| 4|
B5| Slot-Nut M8| 16|
BOX C – Vario VESA triple adapter set HARDWARE KIT
#| Part| QTY| Note
C1| Vario VESA holder| 3|
C2| Vario VESA plate| 3|
C3| Vario VESA pin holder| 6|
C4| Vario VESA pin| 3|
C5| Bolt M6 X 12 DIN 7991| 12| Used with VESA 100/200 adapter.
C6| Bolt M5 X 20 DIN 7991| 12|
C7| Bolt M4 X 16 DIN 7985| 12| Philips head.
C8| Bolt M4 X 10 DIN 7985| 12| Philips head.
C9| Bolt M8 X 16 DIN 912| 6|
C10| Bolt M6 X 16 DIN 912| 12|
C11| Bolt M5 X 16 DIN 912| 12|
C12| Set screw M8 X 40 DIN 916| 9|
C13| Set screw M5 X 20 DIN 916| 6|
C14| Washer M8 DIN 125-A| 6|
C15| Slot-Nut M8| 6|
If you still have some questions regarding assembly of this product or about the manual itself, please refer to our support department. They can be reached at [email protected]
Alternatively, we now have a Discord server where there are quite some
experienced Sim-Lab customers hanging out. They might just help you along if
you ask them nicely 😉 www.sim-lab.eu/discord
If you feel like printing this manual, please consider the environment before
doing so. For the best results, make sure you print at 100% scale without
borders.
Product page on the Sim-Lab website:
Documents / Resources
| SIM-
LAB 75-100 VARIO Triple Monitor
Mount
[pdf] Instruction Manual
75-100, 100-200, 75-100 VARIO Triple Monitor Mount, VARIO Triple Monitor
Mount, Triple Monitor Mount, Monitor Mount, Mount
---|---