pureit Copper Mineral RO UV MF 7 stage Table top Wall Mountable Black and Copper Instruction Manual

pureit Copper Mineral RO UV MF 7 stage Table top Wall Mountable Black and

Copper

INTRODUCTION

• Copper+ RO Product details
• TDS definition
• TDS handheld meter details
• FAQs

KNOW YOUR PUREIT

COPPER+ MINERAL RO+UV+MF

1. LED Display Panel
2. Touch buttons – Copper Enriched Water & Ambient RO Water
3. Water Dispensing Outlet
4. Pre-sediment Filter
5. Inlet Water Tube
6. Reject Water Tube
7. Diverter
8. Ball Valve
9. Drip Tray

UNIQUE FEATURES

• COPPER CHARGE TECHNOLOGY-

  • A unique modern technology that charges water with 99.8% pure copper, in real time.

• **PRECISE COPPER DOSING***

  • Infuses the right amount of copper in every glass of water.

• DUAL WATER DISPENSING

  • Two buttons give you the choice of RO water and copper-charged RO water.

• INTELLIGENT COPPER CLEANING MODE

  • Smartly senses and schedules copper auto-cleaning, for fresh copper infusion at all times.

• ADVANCED 7 STAGE PURIFICATION WITH RO+UV+MF

  • That ensures 100% RO purified water.

• LARGE STORAGE CAPACITY

  • Upto 8 litres^ storage capacity of purified water so that you never run out of RO water.

• DOUBLE PURITY LOCK

  • Digital Advance Alert System, alerts you 15 days** before the life of the Germ Kill Kit gets over and Auto Shut off stops water if the filter is not changed, providing a 100% guarantee of safe and sweet water.

• UNITED STATES ENVIRONMENT PROTECTION AGENCY (USEPA) COMPLAINTS

  • Meets the toughest safety standards by removing 1 crore viruses and 10 crore bacteria from 1 litre of water.

• 100 % FOOD GRADE PLASTIC
  

  • Prevents harmful toxins from leaching into the water, unlike non-food grade plastics.

UNIQUE TECHNOLOGY

This is a graphic representation of filters
An advanced purifier that brings together modern technology and traditional goodness to enhance your family’s health. Its advanced 7-stage purification process with RO+UV+MF purifies water and its proprietary Copper Charge Technology™~ charges it with the goodness of copper.

1. Pre-Sediment Filter (SF)
   • Removes fine and coarse particulate impurities/dirt and improves the life of the Carbon Filter.
2. Pre-RO Carbon Filter
   • Removes chlorine and organic impurities such as harmful pesticides. It also absorbs bad taste and odor-causing organic compounds from water.
3. Mesh Filter
   • Filters water further to ensure the removal of finer particulate impurities.
4. RO Membrane
   • Removes dissolved salts, hardness, pesticides, and heavy metals like arsenic, lead, and mercury. It also removes microbial contaminants like bacteria, viruses, protozoa, and cysts.
5. UV Chamber
   • Acts as an additional stage of purification to further inactivate bacteria, viruses, and parasites to deliver safe water.
6. Post RO Carbon Filter
   • This level of purification acts as a polisher and enhances the taste of purified water.
7. Micro Filtration Membrane
   • The filtration Membrane is the stage after Post-RO and UV, which ensures that the water is purified not once but thrice.

Advance Alert System will alert you 15 days before the end of every 360 days (approximately) or 15 hours before the completion of every 400 hours of pump running time, whichever is earlier. The purifier will communicate the alert only if the Heirs nation one US A lure is or 4 log virus move rom mo contaminated water. Copper charge Te ology is a unique proprietary teal which 5 based on electrocortical is in proper in water. Smart technology ensures precise dosing in every glass of water. Consumption of 2 liters of copper- charged RO water every day, will add up to approximately 30% of the RDA for copper ( for adults, as guided by the Indian Council of Medical Research, ICMR) ^7,6 to 8 liters in running water conditions, ***Applicable for all water contact parts,

INSTALLING YOUR PUREIT COPPER+ MINERAL RO+UV+MF

1. The purifier should be installed by a trained Pureit technician
2. It can be wall-mounted or used as a table top purifier
3. The purifier should be placed in an area that is free of ants/insects/other pests.
4. The purifier should be placed close to the plumbed inlet connection (not more than 2 meters).
5. Do not install the purifier above any electric socket
6. Avoid sharp bends to the pipes of the product
7. Do not use an extension cord
8. Make sure you test the input water TDS (Total dissolved salts) before installing the purifier. The maximum input TDS should not exceed 2000 PPM.

TAKING CARE OF PUREIT COPPER+ MINERAL RO+UV+MF

1. Use only the plug provided with the purifier
2. The purifier should not be connected to any hot water tap. Do not run hot water over 45°C through the purifier
3. Make sure that the power is kept on to dispense the water. Press the Touch button to dispense water from the storage tank.
4. Water from waste water tube is not suitable for drinking. You can use that water for gardening or cleaning floors.
5. Store water only in the purifier and don’t use bottles and containers. If you do so, water may get contaminated.

CLEANING AND MAINTENANCE

Water Dispensing Point

1. Do not use detergents, soap, or wet cloth to clean the external parts. Use a dry and soft cloth to clean the front cover. It is recommended to use a 3M mop cloth for cleaning.
2. Clean the dispenser by using disinfectants like bleach/hypochlorite (50 PPM available chlorine). Discard 2 liters of water after cleaning the dispenser.
3. Discard water from the detachable tray & maintain it in a dry condition.

Storage Tank

1. Discard the water in the storage tank once in 15 days.
2. Drain the water in the storage tank if the purifier is not used for 2 days.
3. Clean the storage tank once a month with a disinfectant solution. To purchase this solution, call us at 1860-210-1000 now.
4. How to clean the tank: Open the cleaning solution dispenser and put 1 ml of the disinfectant solution (10-15 drops) into the storage tank. (Ensure the tank is full). Drain the entire tank after 10 minutes.
5. No foreign material (like dust/ants/insects/other pests) should enter the storage tank. The filtered water in the storage tank may deteriorate in the process.
6. The point-of-use reverse osmosis drinking water treatment systems addressed by NSF-58 standard are designed to be used for the reduction of specific substances that may be present in drinking water supplies (public or private) which are considered to be microbiologically safe and are of known quality.
7. The output water may continue to have flora which are harmless and pose no health hazard to normal healthy adults and children.

Disposal Guidelines (Electrical): To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate electrical items in this product such as power supply adaptor, control circuits, LED panel, and wiring from other types of waste and recycle them responsibly to promote sustainable use of material resources. Contact either the retailer where you purchased this product, or the local government office for details of where and how these items can be taken for environmentally safe recycling.

KEEP YOURSELF SAFE

1. Do not open the purifier for cleaning or for any replacements. This can be done only by a qualified company personnel or an authorized agent.
2. Do not plug or unplug the power cord with wet hands to avoid any untoward accident due to electrical shock or fire.
3. Do not splash the filtration system with water while cleaning.
4. Do not put heavy or sharp objects on the purifier.
5. Never put the cord near stoves or heaters.
6. If the power cord is damaged, it must be replaced and not used again.
7. Always switch-off the “Ball Valve” and electrical power in case you notice any leakage from the purifier or you are going out of home for more than 2 days.
8. Ensure input pressure is more than 10 PSI and less than 30 PSI ***
9. In case UV lamp breaks, carefully sweep all the fragments, wipe the area with a wet towel, and dispose of all the fragments including the used towel in a sealed plastic bag. Open windows to allow room to ventilate. Do not use a vacuum cleaner. Hand over the bag to the service technician for proper disposal of the same when he visits to replace the UV lamp.
10. In case of any smoke or burning smell, switch-off power, remove the plug immediately, and call us at 1860-210-1000.

If the pressure is more than 30 PSI, you need to use a ‘Pressure reducing Valve’ which must be bought at an additional cost, If the pressure is less than 10 PSI then you need to buy a ‘Pressure enhancing Pump’ which can be bought at an additional cost. Ensure you buy them from the authorized service personnel of Pureit.

SF (Sediment Filter)

ATTENTION

• Close the ball valve before opening the SF housing for cleaning.
• Please do not use any abrasive/pointed tool to clean the Sediment
• Filter as it may damage the Sediment Filter.
• In case you observe the rubber ring is dirty, clean the rubber ring & fix it on the housing again properly.
• Clean the inner portion of the housing as well.
• If required, a Spanner for opening ESF housing can be bought from a Pureit service technician.

LED INDICATOR GUIDE

• While the Germkill Kit and the Sediment Filter have a fixed replacement schedule, you might be required to clean/change the SF in the interim depending on the quality of your input water.
• If the External Sediment Filter is not replaced/cleaned in time (when the blue blinking happens), it may affect the performance of the purifier.
• Permeate ow rate and recovery are based on standard test conditions and may vary depending on input water quality, TDS, pressure and life of Filter elements.
• Input water quality and TDS content are important determinants of output water quality.
• If input pressure exceeds 30 PSI, please install a company-provided pressure-reducing valve at an additional cost.
• If the pressure is less than 10 PSI then you need to buy a ‘Pressure enhancing pump’ at an additional cost.
• The device should not be installed in a house where the input pressure is greater than 60 psi.

TECHNICAL SPECIFICATIONS

• After every 400 hours of pump running time or 360 days of clock time, whichever is earlier, the respective Germkill Kit needs to be changed.
• Every 400 hours of pump running time typically gives 4000 liters of purified water under test conditions of 10 PSI input pressure, 750 ppm TDS, and 25 °C temperature.
• Any variations from the test conditions will lead to variations in the littered life.
• Technical specifications are subject to change or improvement without prior notice.
• In case the TDS is >1000 PPM, a company-provided anti-scalant is recommended to be installed. This has to be purchased at extra cost.
• lf the iron content in the input water is higher, it is recommended to install a company-provided iron filter at an additional cost. $ 7.6 to 8 liters in running water conditions.

HANDHELD TDS METER

• What is TDS (Total Dissolved Solids)?
  • TDS is a measurement that refers to the combined total amount of both inorganic and organic substances dissolved in water. These solids include salts such as calcium, magnesium, sodium, potassium, bicarbonates, carbonates, chlorides, etc. as well as organic materials.
• What is a TDS meter?
  • A TDS meter is a small hand-held device, used to indicate the amount of total dissolved solids (TDS) in a solution.
  • Since dissolved ionized solids like salts and minerals contribute to the conductivity of a solution, a TDS meter measures the conductivity of the solution and then converts that figure to an estimated TDS reading.
  • The device is known for quick measurement. This hand-held device is suitable for checking TDS of natural surface water, tap water, tanker water, drinking water, treated water etc.
• What does the TDS meter not measure?
  • A TDS meter does not measure contaminants which means that it will not indicate if the water is healthy or not. The TDS meter reading simply refers to the amount of total dissolved solids in the water, it will not indicate what those solids are and if they are harmful to your health.
  • For example, the device can reflect a high TDS meter reading but no harmful contaminants in the water.
  • Some healthy minerals like potassium, magnesium, and calcium can cause the TDS meter to spike the reading. So, any water filter with a remineralizer could cause a high reading on
  • the TDS meter, even though the remineralizer is adding good minerals.
  • On the other hand, the device can reflect a low TDS level even if several harmful contaminants are present in the drinking water.
  • The water can have heavy metals like lead, or other contaminants like pesticides, pharmaceuticals, or hexavalent chromium. The TDS meter will not pick these contaminants.
  • This is why you shouldn’t rely on a TDS meter to determine the water purity i.e. healthy to consume or not. It is important to not just understand how many dissolved solids are present in the water, but also, what those solids are and if they’re harmful to your health.

USAGE INSTRUCTIONS

KNOW YOUR TDS METER AND ITS USAGE INSTRUCTIONS

For TDS measurement, use only room-temperature water. Do not use hot or cold water. It can display up to 999 ppm TDS if the feed water TDS is more than 999 ppm it will show as 10^1 for 1000 ppm and 2×10^1 for 2000 ppm. This TDS meter can not be used for water samples which has TDS > 2000 ppm. There can be a variation of around ‡ 20% between the value that is being measured by handheld TDS meter and other desktop conductivity meter or when measured using conventional gravimetric method for checking the TDS.

FAQS

• How does Pureit Copper+ Mineral RO+UV+MF work?
  Pureit Copper+ Mineral RO+UV+MF has a 7-stage purification system that ensures you get ‘Safer than boiled water’. It also removes excess total dissolved salts (TDS) to make the water tastier.

• What is the storage capacity of Pureit Copper 1 Mineral RO+UV+MF?
  Pureit Copper+ Mineral RO+UV+MF has a storage tank capacity of up to 8 Litres under running water. The process of filling the storage tank is fully automatic. When you take water out of the tank the purification process automatically refills the storage tank.

• How much time does it take to purify water in Pureit Copper+ Mineral RO+UV+MF?
  Pureit Copper+ Mineral RO+UV+MF can purify water up to 28 liters per hour. However, the time taken to purify is influenced by life of the filters, the input water pressure, and other impurities present in water.

• How will I get the new Consumables/Membranes and Copper module replaced?
  You need to call the Pureit Helpline and order a Germkill Kit™. A technician will visit your place to replace it, at a nominal cost.

• Can I drink the first purification cycle of water from the purifier?
  After Pureit Copper+ Mineral RO+UV+MF is installed or whenever the Germkill Kit™ (s) are replaced, discard the first cycle of water (8 litres) that is filled in the storage tank.

• What should I do if there is no water being dispensed from the spout?
  In case you cannot dispense water from the spout, first check whether the power supply is on. If it is on, then check if there are any fault indicators on, or the “SF/GKK* indicator is blinking. Get either the fault resolved or Germkill Kit™ replaced. If none of these indicators are lit up on the indicator panel, then check if the ball valve is closed. If none of these cases are true, then please call the Pureit helpline for assistance.

• Can I open and service my purifier?
  It is not recommended to open and service the device yourself. Call the Pureit helpline if you face any issue that requires servicing and opening the device.

• Can I use any type of water to purify through my Pureit Copper+ Mineral RO+UV+MF?
  Pureit Copper+ Mineral RO+UV+MF will purify “potable” water for the removal of hardness and other impurities to give you safe drinking water. If the input water has impurities normally not present in drinking water (high iron/ turbidity/ microbial contamination etc.) or water is from an unknown source (river/lake/pond/borewell etc.)| then suitable pre-treatment may be required.

• The Advance Alert System™ did not give me 15 days warning before the purifier stopped working. Why is it so?
  There may be several reasons for this: While the Germkill Kits and the Pre- Sediment Filter have a pre-determined life, depending on your input water quality the Pre-Sediment Filter might need a replacement/cleaning even before the purifier gives you an alert. In such cases, please contact the Pureit helpline and get the Pre-Sediment Filter replaced/cleaned. The purifier will communicate the alert only if the purifier is in a switched-on condition during the scheduled alert time. Post the completion of the scheduled alert time, Auto Shut off™ of water will be activated automatically for GKK, even if the purifier is in a switched-off condition. Does Pureit Copper+ Mineral RO+UV+MF remove arsenic, fluoride, and nitrates? Yes. RO technology can remove arsenic, fluoride, and nitrates.

• Can I use the reject water?
  It is not recommended to use rejected water for any kind of consumption (drinking or cooking). I can probably be used for gardening or floor cleaning.

• What should I do if any part of the purifier is broken?
  Please call the Pureit helpline to guide you on any repairs required. You might need to buy the replacement parts at an additional cost.

• What should I do if there is a leakage from the purifier?
  Turn off the ball valve and switch off the power, if you find any failure. Check for any visually improper fitment and then call the Pureit helpline and register a service request. How long the stored water in Pureit Copper+

• Mineral RO+UV+MF can be used for drinking?
  It is recommended for the stored water to be consumed within 2 days. Water stored for over 2 days should ideally be discarded.

• How do I know when I have to change my Germ Kill Kit™?
  Pureit Copper+ Mineral RO+UV+MF has an indicator panel with SF/GKK indicator that will blink to prompt you to call the Pureit helpline to get the respective GKK changed, whenever the life of the Germ kill Kit™ is near expiry (refer to “Understanding LED indicator panel” section of this user manual for further details).

• Can the Pre-Sediment Filter or the other Do filter parts choke before the Advance Alert?
  While the Germkill Kit™ and the Pre-Sediment Filter have a pre-determined life, you might be required to change the filters in the interim depending on the quality of your input water. Should the tap flow rate be very low or if it is taking too long for the tank to fill, then please contact the Pureit helpline to change the membranes. These extra visits will be chargeable as per T&C.

• For how long can I continuously dispense water?
  Once the Soft-Touch button is pressed water dispenses for 3 minutes (2 minutes if in Warning/ ASO/Fault condition) and it automatically stops dispensing after that. In case you need more water, you need to press the button again. You can stop the flow of wate in between by pressing the Soft-Touch button again.

• Will the Guided Alert System indicate any leakage complaints?
  No. It only indicates key electrical faults.

• How can I clean my Pureit Copper+ Mineral RO+UV+MF?
  To clean the device body clean dry or wet wiping with a 3M foam mop/cloth is recommend- ed. Do not spray water on the device’s front cover as it may damage the electronic part. Do not use soap or hard cleaning detergents.

• What should I do if the water from the purifier tastes unusual or if the purification is taking more time?
  Please call the Pureit helpline. A technician will visit you to help resolve the issue.

• What should I do if the copper-charged RO water is not dispensing?
  Please check if the Copper RO Water LED is blinking yellow, if yes then please wait as the device is in Copper Auto-Cleaning Mode. Once the auto-cleaning process is complete you can dispense Copper RO water by pressing the Soft- Touch button. If the copper LED is red, it will not allow dispensing. In such a case check for the presence of water from the main line, wait for some time, then switch off and switch on the purifier again. If the LED is still red, then contact the Pureit helpline.

• Can I dispense water in the absence of electricity?
  Depending on the amount of water already filled in the tank, you can dispense up to 8 liters of water even without electricity when the tank is full by installing a manual tap as a spare by an authorized service technician. However, Copper RO water can be dispensed only with electricity as Copper is infused in real-time.

CONTACT

• Pureit Helpline
• 1860-210-1000
• www.pureitwater.com.
• To know more
• Contact Pureit helpline number 1860 210 1000
• Or Visit: www.pureitwater.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>