Pureit RO ADVANCED MAX MINERAL PURIFIER Instruction Manual

Pureit RO ADVANCED MAX MINERAL PURIFIER

KNOW YOUR PUREIT ADVANCED MAX MINERAL RO+UV+MF+MP PURIFIER

1. LED Indicator
2. Tap
3. Waste Water Tube
4. Compound ESF Outlet Tube
5. Water Level Indicator
6. Compound ESF
7.  ESF Inlet Tube
8. Diverter
9. Ball Valve

UNIQUE FEATURES OF PUREIT ADVANCED MAX MINERAL RO+UV+MF+MP PURIFIER

PUREIT ADVANCED MAX MINERAL RO+UV+MF+MP PURIFIER’S ADVANCED PURIFICATION

PROCESS

This is a graphic representation of filters

1. Pre Sediment Filter
   Removes visible dirt and impurities.

2. Membrane Protector
   Removes chlorine, harmful pesticides, bad taste and odour-causing organic compounds, increasing the life of the RO membrane.

3. Minifilter
   Filters water further to ensure removal of finer particulate impurities.

4. RO Membrane
   Removes dissolved salts, hardness, pesticides and heavy metals like arsenic, lead and mercury, microbial contaminants like bacteria, virus, protozoa and cysts.

5. UV Chamber^
   Additional stage of purication that destroys bacteria, virus and parasites.

6. Micro Filtration (MF) Membrane^
   Additional stage of purification to further purify water.

7. Post RO Carbon Filter
   Acts as a polisher and enhances the taste of purified water.

INSTALLING YOUR PUREIT ADVANCED MAX MINERAL RO+UV+MF+MP PURIFIER

1. The purifier should be installed by a trained Pureit technician.
2. It can be wall-mounted or used as a table top purifier.
3. The purifier should be placed in area which is free of ants/insects/other pests.
4. The purifier should be placed close to the plumbed inlet connection (not more than 2 metres).
5. Do not install the purifier above any electric socket.
6. Avoid sharp bends to the pipes of the product.
7. Do not use an extension cord.
8. Before installing the purifier please check the inlet pressure.
9. Make sure you test the input water TDS (Total dissolved salts) before installing the purifier. The maximum input TDS should not exceed 2000 PPM.
10. Do not connect the purifier to any hot water tap.
11. Please do not terminate the reject line tubing directly into the drainage (keep it hanging over the drainage).
12. Do not place the unit where it will be exposed to freezing and/or direct sunlight and ensure there is enough ventilation.

TAKING CARE OF YOUR PUREIT ADVANCED MAX MINERAL RO+UV+MF+MP PURIFIER

Cleaning

1. Clean the tap nozzle using disinfectants like bleach/hypochlorite (50 PPM available chlorine). Discard 2 litres of water after cleaning the dispenser.
2. Clean the external portion of the purifier using a dry cloth only. Do not use any detergent or soap.
3.  Do not clean aggressively or rub the surface as this might lead to scratches on the parts.
4. Never splash water on the purifier while cleaning.
5.  Do not try to open the purifier for cleaning or for any replacements. This can be done only by a qualified company personnel or an authorised agent.
6. You should maintain good hygiene in the area around your water purifier. Ensure that this area is free of ants/insects/other pests.
7. Do take care of the reject line and other tubes while cleaning the purifier else water can flow into the kitchen.

Storage Tank

1. Discard the water in the Storage Tank once in 15 days through the tap.
2. Always drain the water in the Storage Tank if you have not used the purifier more than 2 days.
3. Do not allow any foreign or unexpected material (like dust/ants/insects/other pests) to enter into the storage tank. The filtered water in the storage tank may deteriorate in the process.

Other Important Instructions

1. When you are away / during over head tank cleaning always ensure to switch off the electrical power and the ball valve.
2. Do not put any heavy or sharp objects on the purifier.
3. Please dispose the used consumables like Sediment Filters, Carbon Filters and Membranes along with the other household waste through the municipal disposal system.

Disposal Guidelines (Electrical): To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate electrical items in this product such as power supply adaptor, control circuits, LED panel and wiring from other types of waste and recycle them responsibly to promote sustainable use of material resources. Contact either the retailer where you purchased this product or local government office for details of where and how these items can be taken for environmentally safe recycling.

KEEP YOURSELF SAFE

1. Do not consume the water from the waste water tube for drinking purpose. However, you can use that water for gardening or cleaning the floors.
2. Do not plug or unplug the power cord with wet hands. Ensure that the plug isn’t wet while plugging in, or plugging out to avoid risks such as electrical shock or fire.
3. Keep the cord away from wiring conjunctions to avoid hazard. Never put the cord under rugs, near heat resistors, radiators, stoves or heaters.
4. If the power cord is damaged, the power cord must be replaced and not used.
5. In case of any smoke or burning smell, remove the plug immediately and call the Pureit Helpline.
6. When shifting your house, get the purifier duly inspected and packed by the Pureit service technician. Remove water from the Storage Tank and pack the purifier properly in case of shifting.
7. Please ensure to switch off the power whenever you turn off the Ball Valve.
8. The point-of-use reverse osmosis drinking water treatment systems addressed by NSF-58 standard are designed to be used for reduction of specific substances that may be present in drinking water supplies (public or private) which are considered to be microbiologically safe and are of known quality.
9. The output water may continue to have flora which are harmless and pose no health hazard to normal healthy adults and children.

UNIQUE ADVANCE ALERT SYSTEM

• During the initial start up, the tank full LED and GKK LED will light up for 2 seconds. GKK LED will come on Red-Green-Blue sequence. The tank full LED will blink for max. 15 minutes and then restore to normal operation thereafter.
• In case of any key electrical faults (RO Pump, UV Fault) GKK LED will start blinking Red-Green-Blue in sequence.
• The blinking blue for sediment filter change will happen from approximately 165-180 days of clock time or 150-165 hours of pump running time,whichever is earlier, after device installation or GKK replacement. You can either clean the SF or call Pureit Helpline for buying a new SF at a nominal cost.
• Approx. 330 hours of pump running time or 360 days of clock time, whichever is earlier the respective Germkill Kit needs to be changed. Approx. 330 hours of pump running time typically gives 6000 litres of purified water under test conditions of 10 PSI input pressure. 750 ppm TDS and 25˚C temperature. In case of replacement. Variations from the test conditions could lead to variation in filtered water volume.
• While the Germkill Kits and the Sediment Filter have a fixed replacement schedule, you might be required to change the SF in the interim depending on the quality of your input water.

TECHNICAL SPECIFICATIONS

• 5.8 to 6.1 under running water conditions Permeate flow rate and recovery are based on standard test conditions and may vary depending on input water quality, TDS, pressure and life of Filter elements.
• Input water quality and TDS content are important determinants of output water quality.
• If input pressure exceeds 30 PSI, please install a company provided pressure reducing valve at an additional cost.
• If the pressure is less than 10 PSI then you need to buy ‘Pressure enhancing pump’ at an additional cost.
• Device should not be installed in a house where input pressure is greater than 60 PSI.
• Post-RO Carbon Filter fitted in the device may need to be changed intermittently at extra cost in case you face smell issues. Technical specifications are subject to change or improvement without prior notice.
• In case the TDS is >1000 PPM, a company provided anti-scalant is recommended to be installed
• This has to be purchased at extra cost.
• If the iron content in the input water is high, it is recommended to install a company provided iron removal filter at 5
  an additional cost.

FAQs

• How does Pureit Advanced Max Mineral RO+UV+MF+MP purify water?
  Pureit Advanced Max Mineral RO+UV+MF+MP has a 7-stage purification process which ensures you to get water that is ‘As Safe As Boiled Water’ and also removes excess Total Dissolved Solids (TDS) to make your water tastier.

• Stage 1st
  Pre-Sediment Filter: Removes visible dirt and impurities.

• Stage 2nd:
  Membrane Protector: Removes chlorine, harmful pesticides, bad taste and odour- causing organic compounds, increasing the life of the RO membrane.

• Stage 3rd:
  Mini Filter: Filters water further to ensure removal of finer particulate impurities.

• Stage 4th:
  RO Membrane: Removes dissolved salts, hardness, pesticides and heavy metals like arsenic, lead and mercury, microbial contaminants like bacteria, virus, protozoa and cysts.

• Stage 5th:
  UV Chamber: Additional stage of purication that destroys bacteria, virus and parasites.

• Stage 6th:
  Micro Filtration (MF) Membrane^: Additional stage of purification to further purify water.

• Stage 7th:
  Post RO Carbon Filter: Acts as a polisher and enhances the taste of purified water.

• What is the storage capacity of Pureit Advanced Max Mineral RO+UV+MF+MP?
  Pureit has Storage Tank capacity of upto 6L. The storage tank is fully automatic and well shielded and as and when you take water out of the tank, the purification process starts automatically again and refills the Storage Tank.

• How much time does it take to purify water in Pureit Advanced Max Mineral RO+UV+MF+MP?
  Pureit can purify water upto 20 litres/hour depending on the device you have purchased. However, the time taken to purify depends on the life of the filters, the input water pressure, TDS and other impurities present in the water.

• Does Pureit Advanced Max Mineral RO+UV+MF+MP remove arsenic, fluoride and nitrates?
  Like other ions, the RO technology can also remove arsenic, fluoride and nitrates. How will I get new consumables/membranes replaced?You need to call the Pureit Helpline and order the consumables. The customer care specialist will visit your place and replace the consumable/Germkill Kit at a nominal cost.What are all the consumables which are to be replaced?You need to clean/replace Sediment Filter approximately every 6 months from the date of installation based on the input water quality conditions and GKK approximately every 1 year from date of installation.

• Can I drink the first purification cycle of water from the purifier?
  No, recommendation is to throw the first cycle of water that is filled in the Storage Tank when the new Pureit
  purifier is installed and also whenever the Germkill Kit are replaced.

• Can I open and service my purifier?
  It is not recommended to open and service purifier by an individual. Call our Pureit Helpline if you face any issue which requires servicing and opening of the purifier.

• Can I use reject water?
  It is not recommended to use the reject water for any kind of human/pets consumption (drinking or cooking). It may be used for gardening or cleaning floors.

• What should I do if any part of purifier is broken?
  Please call the Pureit Helpline. Our technicians will visit your house and guide you on the repairs required. There will be a nominal visiting charge and you would need to buy the parts required.

• What should I do if there is leakage from the purifier?
  First switch off the Ball Valve if you find any leakage from the purifier and turn off the power switch. Check for any visual improper fitment and then call our Pureit Helpline number and register a service request.

• How long the stored water in Pureit Advanced Max Mineral RO+UV+MF+MP can be used for drinking?
  You can use stored water for 2 days. If it is not used for more than 2 days we advise you to discard that water, refill and then consume.

Reach Pureit @ 1860-210-1000 1860-180-1000 www.pureitwater.com

References

• pureitwater.com

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>