TOPDON BT Mobile Pros 12V Wireless Battery and System Tester User Manual

BTMOBILE PROS
12V Wireless Battery and System Tester
USER MANUAL

BT Mobile Pros 12V Wireless Battery and System Tester

Welcome
Thank you for purchasing the TOPDON BTMOBILE PROS wireless battery tester. Please read and understand this manual carefully before using this product. If any issues arise from the operation of this product, you are welcome to contact us via support@topdon.com for official technical support.
About
TOPDON BTMOBILE PROS meets a variety of battery specifications including CCA, JIS, EN, DIN, SAE, IEC, etc., and also an effective detector to pinpoint the bad cell.
It adopts the most advanced conductivity detection technology to effectively help maximize the performance of your 12V vehicles, giving valuable, easy-to- understand information about the vehicle battery health, alternator’s charging, and starter’s cranking conditions.
The built-in ExtraSafe protections against short circuit, reverse polarity, and over voltage allow the tester to safely connect to any battery.

Package List

1. TOPDON BTMOBILE PROS*1
2. User Manual
3. EVA Carrying Case

Compatibility

Please be noted that battery type and CCA values (Cold Cranking Amp) are marked on the battery label. Please refer to it before using BTMOBILE PROS.

1. Regular Flooded
2. AGM Flat plate
3. AGM Spiral
4. GEL
5. EFB

NOTE: If your vehicle battery is not the battery mentioned above and you are not sure about which type it is, please choose AGM to conduct test, and the error is within 10%.

Guide to LED Indicator

APP Installation & Setup

Installation:
Please scan the QR code or visit our offical website: https://www.topdon.com/products/btmobile-pros to download and install the APP.

NOTE: Compatible with Android 4.4 smart devices, or newer.
Set up
For the first time, you can choose to register with email or skip login. But we strongly recommend the registration for latest product news and timely technical assistance.

BTMobile Pros

Operation Introduction

Before Test:

1. Before you test a battery in a vehicle, turn off the ignition, all accessories and loads. Close all of the vehicle’s doors and trunk lid.

2. Make sure the battery terminals are clean. Use a wire brush to clean them, if necessary.
   NOTE: This tester works best if the battery connectors have been removed and the battery posts have been cleaned. Any corrosion between the tester clamps and the battery connectors, or between the battery connectors and the battery posts, will degrade the tester’s efficiency.

3. Connect the RED (+) Positive Battery Clamp to the (+) positive battery terminal, and connect the BLACK (-) Negative Battery Clamp to the (-) negative battery terminal. Ensure that the clamps are securely attached to the correct terminals.

4. Open the Bluetooth on mobile device or tablet.

5. Test Introduction

• BATTERY TEST: Display SOH (State of Health), SOC (State of Charge), Voltage, Test Value, Internal Resistance, and the readable analysis results on App;
• CRANKING TEST: Analyze the actual cranking voltage and the cranking time to help you quickly figure out the whole state of the starting system;
• CHARGING TEST: Test different parts of charging system, including generator, rectifier, rectifier diode, and so on for a reliable charging volt value.

1. Battery Test (for 12V battery)

1. Open the APP on your tablet and log in.

2. Click “Bluetooth-SCAN”, search for the matching device name.

3. Click the matching device name to connect.

4. Click “Battery Test” on the home screen.

5. Select battery type and click the corresponding type.

6. Select the battery standard marked on the battery label, and click the corresponding type.
   NOTE: If the battery is JIS standard, please refer to the table for value and select CCA (SAE) as the test standard (please Google JIS to CCA).

7. Select battery capacity value marked on the battery label.

8. Click “NEXT” and wait a few seconds for results.

9. Click “Share” to share the results.

2. Cranking Test
NOTE: The engine and all other accessory loads must be OFF before test.

1. Click “Cranking Test”.
2. Follow the steps and start vehicle.
3. Click “OK” to get the results.
4. Click “Share” to share the results.

3. Charging Test
NOTE: The engine must be ON during test.

1.  Click “Charging Test”.
2. Follow the steps and start vehicle.
3. Step on the accelerator, increase the value of RPM to 2500, keep it for 5 seconds.
4. Click “OK” to get the results.
5. Click “Share” to share the results.

4. System Test (Overall Test for Battery)

1. Click “System Test” .
2. Follow the steps to complete all tests (refer to Battery Test, Cranking Test, Charging Test for details).
3. After completing all test, the test result report will generate automatically. Drop down to see each test result.

5.Test Report

1. Select “Test Report” on the home screen.
2. Click the test report which you want to check. Or you can select it and delete it.

Battery Library

1. To know your battery information, you can check on Battery Library. Click “Battery Library” on the home screen. Follow the prompts, select your options such as  vehicle TYPE, MAKE, MODEL, YEAR and CC.
2. The result will show automatically:

Technical Specification

Operating Voltage: 8V~16V
Working Temperature: -10°C to 45°C (14°F to 113°F)
Storage Temperature: -20°C to 75°C (-4°F to 167°F)
Clamp Line Length: 556mm (21.89 inch)
Safety Protection: Reverse Polarity Protection

Warranty
TOPDON One Year Limited Warranty
The TOPDON Company warrants to its original purchaser that TOPDON products will be free from defects in material and workmanship for 12 months from the date of  purchase (Warranty Period).
For the defects reported during the Warranty Period, TOPDON will, according to the technical support analysis and confirmation, either repair or replace the defective part or product.
This limited warranty is void under the following conditions:
Misused, disassembled, altered or repaired by a non-TOPDON technical repair specialist.
Careless handling and violation of operation.
Notice: All information in this manual is based on the latest information available at the time of publication and no warranty can be made for its accuracy or completeness.  TOPDON reserves the right to make changes at any time without notice.

Warnings
DO NOT place the tester near the engine or exhaust pipe to avoid damage from high temperatures.
DO NOT smoke, cause sparks, or strike matches near the battery when testing.
DO NOT remove battery clamps while testing.
DO NOT put the tester into a highly humid or dusty environment.
DO NOT disassemble the tester.

FCC Warnings:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this  device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide  reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and  used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a  particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the  user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Cautions
Use this tester in accordance with these instructions, taking into account the working conditions and the work to be performed.
Hazardous results could occur if tool is used for purposes not intended.
Before testing, make sure the battery terminals are clean. Grease and dust could result in inaccurate test results.
Wear eye protection when working around batteries.
Check the insulation layer of the battery clamps is in good condition (no damage, bareness or disconnection) to avoid electric shock.
Test in a well-ventilated area. Vehicle exhaust contains toxic carbon monoxide.
Keep hair, hands, and clothing as well as tester leads and cords away from moving blades and belts.
Keep the tester out of the reach of children.

FAQ

Q: Can BTMOBILE PROS test the battery installed in the vehicle?****

– A: Yes, it supports in-vehicle and out-of-vehicle testing.

Q: Is the test result accurate?****

– A: Yes. Our BTMOBILE PROS features advanced conductance detection giving you accurate test results in seconds.

Q: What batteries can BTMOBILE PROS work on?****

– A: It works on 12V regular flooded, AGM Flat plate, AGM Spiral, GEL and Deep Cycle batteries,with CCA between 100 to 2000.

Q:Is BTMOBILE PROS designed with any built-in protections?****

– A:Yes. It offers peace of mind with extra-safe Reverse Polarity and Sparkproof protection, and easy operations even if you’re new to battery testing.

Q: How do I confirm if my vehicle battery is bad or good?****

– A: The battery tester will display SOH (State of Health), SOC (State of Charge), CCA (Cold Cranking Ampere), Voltage, Internal Resistance, and Rating, with an intuitive test result of “GOOD” or “BAD” for your reference.If the internal resistance is too large, it indicates a broken battery.

Q: Can this battery tester estimate the remaining capacity of my battery?****

– A: Yes.The battery tester will display SOC (State of Charge) to express as a percentage of your battery’s rated capacity, a measure of its condition to assess the potential energy.

Note that a decent SOC (State of Charge) doesn’t mean the battery is in good condition. You need to refer to your battery’s actual CCA Value and Internal Resistance for further analysis.

For Services and Support
86-755-21612590
1-833-629-4832 (North America)
support@topdon.com
www.topdon.com
@TopdonOfficial
f @TopdonOfficial

References

• TOPDON|Automotive Diagnostic Tools, Battery Tools and Key Programmers – TOPDON TECHNOLOGY Co., Ltd.
• TOPDON Battery Tester BTMobile Pros – Topdon Technology Co., LIMITED
• TOPDON|Automotive Diagnostic Tools, Battery Tools and Key Programmers
• Collections – TOPDON TECHNOLOGY Co., Ltd.
• TOPDON Battery Tester BTMobile Pros – Topdon Technology Co., LIMITED

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>