bticino XW8002W Thermostat With Integrated Wlan Interface Instruction Manual
- June 13, 2024
- bticino
Table of Contents
bticino XW8002W Thermostat With Integrated Wlan Interface
Product Information
Product Name: XW8002W
Product Features:
- Touch screen display
- Temperature and humidity display
- Boost mode indicator
- Wi-Fi connection capability
- Temperature setting keys
- Reset key
- Manual mode indicator
- Heating and cooling indicators
- Thermostat indicator
- Connection clamps for installation
Manufacturer: BTICINO SpA
Manufacturer Address: Viale Borri, 231, 21100
VARESE ITALY
- Power Supply: 110-240V, 50/60Hz
- Max Power Consumption: 2W
- Current Rating: 5(2)A
Product Usage Instructions
- Display touch-screen: Use the touch-screen display to interact with the device.
- Tasto connessione WiFi: Press this button to connect the device to a Wi-Fi network.
- Tasti per impostazione temperatura: Use these keys to set the desired temperature.
- Tasto Reset: Press and hold this button for 10 seconds to restore the device to its factory settings.
- Indicatore riscaldamento acceso: This indicator shows when the heating function is turned on.
- Indicatore raffrescamento acceso: This indicator shows when the cooling function is turned on.
- Indicatore Termostato spento: This indicator shows when the thermostat is turned off. In heating function, it indicates temperature (frost guard) and in cooling function, it shows “OFF”.
- Indicatore connessione Wi-Fi: This indicator shows the status of the Wi-Fi connection.
- Morsetti di collegamento: Use the connection clamps as per the provided diagrams for installation.
Note: Avoid fastening the base on irregular surfaces and excessive screw tightening to prevent base distortion. Ensure that the front is tightly fixed to the base and the fastening clip locks into place. After installation, wait for 2 hours before checking the read temperature.
Installation
Recommended height, unless different regulations are specified.
Caution: avoid fastening the base on irregular surfaces and excessive
screw tightening, in order to prevent any base distortion that may compromise
the correct installation of the device. The front must be tightly fixed to the
base and the fastening clip should lock into place.
Once the installation has been done, wait for 2 hours before checking the read
temperature.
- Touch screen display
- Temperature/humidity display
- “Boost” mode indicator
- Wi-Fi connection key
- Keys for temperature setting
- Boost mode activation
- Reset key (keep pressed for 10”, it restores the factory settings)
- Manual mode indicator
- ON heating indicator
- ON cooling indicator
- “OFF thermostat” indicator; temperature (frost guard) in heating function; OFF in cooling function.
- Wi-Fi connection indicator
- Connection clamps (see diagrams)
- During power shortage the device is not working and not reachable, any collection of personal data is stopped.
Wiring Diagrams
-
System only for heating with clean contact (e.g. boiler agreement)
-
System only for heating with load to be controlled to the network voltage (e.g. 230Vac solenoid valve)
-
Heating and cooling with floor system
-
Heating and cooling with different systems
Available Features
- Management with Home + Control App
- Display and change the temperature
- Boost
- Room humidity display
- Compatible with Netatmo Additional Smart Radiator Valve
- Compatible with Google Assistant
- Compatible with Alexa
- Compatible with HomeKitt
Technical Data
Power supply | 110 – 240 Vac , 50/60Hz |
---|---|
Absorption | 2 W max |
Maximum cable section | 1 x 1.5mm2 |
Contact output | 5(2) A |
Operating temperature | 5 – 40 °C |
Setpoint for heating | 5 – 30 °C |
Setpoint for cooling | 5 – 40 °C |
Type of activation | 1BU |
Pollution level | 2 |
Rated pulse voltage | 4 kV |
Wireless device in compliance with 802.11b/g/n standard, frequency 2.4 – 2.4835 GHz, transmission power < 20 dBm. WEP/WPA/WPA2 safety protocol. Protocol IPv4.
Radio link: short range communication, frequency 868MHz/915MHz, transmission power < 25mW e.r.p.
For device configuration and installation and for any other information, refer to the documentation that can be downloaded from the website.
www.homesystems-legrandgroup.com
Look for “Home + Control” to download the application in Apple Store or Google Play
- ANDROID: Requires Android 5.0 and higher with access to Google Play.
- iOS: Requires an iPhone, iPad, or iPod touch with iOS 12,0 or later.
This device includes Open Source software. For information on licenses and software used, please see the product technical sheet.
Warnings and Consumer Rights
Read carefully before use and keep for future reference
- Touching the units with wet hands is forbidden
- Using liquid cleaners or aerosols is forbidden
- Blocking the ventilation openings is forbidden
- Modifying the devices is forbidden
- Removing protective parts from the devices is forbidden
- Exposing the unit to water drops or splashes is forbidden.
- Installing the units near heat/cold sources or hot/cold air emission points is forbidden.
- Installing the units near harmful gases and powders is forbidden.
- Fastening the units on unsuitable surfaces is forbidden.
Danger of electrical shock
- Risk of devices falling because the surface on which they are installed collapses or inappropriate installation.
- Switch the power supply OFF before any work on the system
- Caution: remote operation may cause damage to people or property.
- Caution: Installation, configuration, starting-up and maintenance must be performed exclusively by qualified personnel.
- Check that the wall installation has been carried out correctly according to the installation instructions.
- Check that the unit installation complies with the standards in force.
- Connect the power supply wires as indicated.
- Use only the items indicated in the technical specifications for any system expansions.
Controlling this HomeKit-enabled accessory automatically and away from home
requires a HomePod, Apple TV, or iPad set up as a home hub. It is recommended
that you update to the latest software and operating system.
Apple HomeKit technology provides an easy, secure way to control your home’s
thermostats from your iPhone, iPad, Apple Watch, HomePod, or Mac using the
Apple Home app. Control your HomeKit-enabled accessories with your voice by
asking Siri directly from your iPhone, iPad, Apple Watch, HomePod, or Mac.
Use of the Works with Apple badge means that an accessory has been designed to
work specifically with the technology identified in the badge and has been
certified by the developer to meet Apple performance standards. Apple is not
responsible for the operation of this device or its compliance with safety and
regulatory standards.
© 2019 Apple Inc. All rights reserved. Apple, the Apple logo, Apple TV, Apple
Watch, HomeKit, iPad, iPhone, Mac, and Siri are trademarks of Apple Inc.,
registered in the U.S. and other countries. HomePod, iPadOS, Multi-Touch, and
tvOS are trademarks of Apple Inc. App Store, iCloud, and iTunes Store are
service marks of Apple Inc., registered in the U.S. and other countries. IOS
is a trademark or registered trademark of Cisco in the U.S. and other
countries and is used under license. Other product and company names mentioned
herein may be trademarks of their respecti ve companies.
Google, Google Play, Android, and related marks and logos are trademarks of
Google LLC.
- Warning: Unique Apple HomeKit installation code to be stored somewhere safe.
- Apple HomeKit: The user will be asked for this code during the installation of the iOS mobile app.
Hereby, BTicino S.p.A. , declares that the radio equipment type Smarther with Netatmo item XW8002W is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.bticino.it/red
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>