bticino 373005, 6, 7 Touch Screen Video Indoor Unit Installation Guide
- June 12, 2024
- bticino
Table of Contents
bticino 373005, 6, 7 Touch Screen Video Indoor Unit
Product Information
- Product Name: DoorBell
- Model Numbers: 373005, 373006, 373007
- Dimensions: – Height: 27 mm – Width: 8 mm – Length: 142.5 mm –
- Depth: 49 mm
- Recommended Height: 49 mm
- Power Supply: DC24V
- Connectivity: RJ45
- Maximum Consumption: 560 V
- Operating Temperature: 12 V
- IP Degree of Protection: F8 F7 F6 F5 F4 F3 F2 F1
- Website : www.homesystems-legrandgroup.com
Product Usage Instructions
- Connect the DoorBell to a DC24V power supply using the provided power supply clamp.
- Connect the additional SOS call clamp and doorbell call clamp to their respective terminals.
- If using an RJ45 connection, connect the cat5/5e/6 FTP or cat5/5e/6 UTP cable with ferrite supplied to the connector.
- Make sure to use only POE power supplies identified with 375002, as the device does not support standard POE power supplies.
- Place the DoorBell at a recommended height of 49 mm, unless specified by different regulations.
- The DoorBell features a 7-inch touch screen display for easy navigation.
- The microphone and loudspeaker are available for audio communication.
- The product also includes a clamp for additional SOS calls and a clamp for doorbell calls.
- The device has an IP degree of protection specified by the F8 F7 F6 F5 F4 F3 F2 F1 rating.
- The maximum relative humidity for proper operation is not specified in the given information.
- The display resolution is not specified in the given information.
For more detailed information and support, please visit the website www .homesystems-legrandgroup.com.
Dimensional data
Recommended height, unless different regulations are specified.
Mounting
The RJ45 cable must be at least 200 mm long
Disassembling
Front and rear view
- Display 7″ (touch screen)
- Microphone
- Loudspeaker
- Clamp for additional SOS call
- Clamp for doorbell call
- RJ45 Connector ( * )
- Power supply clamp 24Vdc
- Alarm connection clamp (see table)
This device does not support standard POE power supplies, but only POE power supplies identified with 375002. Connect the cat5/5e/6 FTP or cat5/5e/6 UTP cable with ferrite supplied to the connector
Alarm connection clamp
- F1 – Infrared
- F2 – GND Magnetic contact
- F3 – GND Smoke sensor
- F4 –GND Gas sensor
- F5 – GND Water sensor
- F6 – GND Magnetic contact F7 – GND
- F8 – GND SOS
- +12V – GND massimo 150 mA – 12 Vdc
All contacts must be connected to GND and the corresponding dedicated input. The functions and wiring mode of the inputs are set by default as shown in the table and diagram, they can be customized using the software and/or straight from the device. Doorbell input isn’t customizable and SOS-GND is disable by default.
Configuration
www.homesystems-legrandgroup.com
The device must be configured by software. For software download, installation device documentation and for any other information, refer to the website.
Technical data
- Voltage 24 Vdc
- Maximum consumption 0,16 A
- Max. cable section for clamps 0.8 mm²
- Operating temperature (- 10) – (+ 40)°C
- IP degree of protection IP30
- Maximum relative humidity 90 %
- Display resolution 1024 x 600 dpi
Warnings and consumer rights
- Read carefully before use and keep for future reference.
- Touching the units with wet hands is forbidden.
- Using liquid cleaners or aerosols is forbidden.
- Blocking the ventilation openings is forbidden.
- Modifying the devices is forbidden.
- Removing protective parts from the devices is forbidden.
- Exposing the unit to water drops or splashes is forbidden.
- Installing the units near heat/cold sources is forbidden.
- Installing the units near harmful gases and powders is forbidden.
- Fastening the units on unsuitable surfaces is forbidden.
- The danger of electrical shock.
- Risk of devices falling because the surface on which they are installed collapses or inappropriate installation.
- Switch the power supply OFF before any work on the system.
- Remote operations may cause damage to people or property.
- Caution: Installation, configuration, starting-up and maintenance must be performed exclusively by qualified personnel.
- Check that the wall installation has been carried out correctly according to the installation instructions.
- Check that the unit installation complies with the standards in force.
- Connect the power supply wires as indicated.
- Use only the items indicated in the technical specifications for any system expansions
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>