H Koenig oly900 Oil Press Instruction Manual

H Koenig oly900 Oil Press

Product Information

Product Name

oly900 Oil press

General Description:

The oly900 Oil press is a machine designed to process various seeds and nuts such as sunflower seeds, pumpkin seeds, flaxseed, sesame, rapeseed, peanuts, walnuts, and more.
It is important to consult the list of processable items in the user manual for accurate usage.

Technical Specifications:

• Switching Control: ON / OFF
• Dimensions: 355 178 264 mm
• Thermal Control: Temperature probe + Thermal protection
• Motor Power: 180 W
• Heating Mode: Heating element and extrusion shaft
• Heating Power: 330 W
• Output Power: 510 W
• Voltage Rating: 220-240V~/50-60 HZ
• Weight: 6.8 KG

Accepted Seeds:

• Brown flax seeds
• Mustard seeds
• Chia seeds
• Cashews nuts
• Peanuts
• Hazelnuts
• Raw coconut
• Almonds
• Pistachios
• Hemp seeds
• Grape seeds
• Sunflower seeds
• Macadamia nuts
• Walnuts
• Rapeseed
• Brazil nuts
• Pine nuts
• Pumpkin seeds
• Poppy seeds
• Sesame seeds
• Pecans
• Argan seeds
• Coriander seeds

Warning:

This oil press does not allow the extraction of olive oil.

Product Usage Instructions

1. Rotate to open the hopper lid.

2. Put the ingredients in the hopper.
   Note: Please use clean and high oil content ingredients (dried). If they contain stones, sand, or metal, this could damage the inner parts. Ingredients larger than a peanut should be cut into smaller pieces before being inserted.

3. Close the hopper lid and put the oil box below the extrusion hole.

4. Connect to the power source and press the Power button, the selection screen will be lit.
   Note: The hopper lid must be in the correct position; otherwise, the machine won’t work.

5. Select the proper program, according to the ingredient you are using.*

6. Press the Start/Pause button, the light will flash when the machine starts to preheat.

7. The oil pressing machine has 7 Presets as follows: Peanuts, Sesame, Sunflower Seeds, Rapeseeds, Flaxseeds, Walnut Core, Mixed. Select the proper program for the ingredient you are using. If the seed or nut is not listed, consult the matching table.

8. Preheating will last for about 30 seconds – 1 minute, depending on the program you have selected; then, the pressing operation will start.

9. The machine will automatically stop after 1 minute and power off after 5 minutes if the hopper has no ingredients inside. You need to press the Power button to start squeezing again.

10. The machine will automatically stop cooling down if it has been working for more than 45 minutes. Then, it won’t work for the next 30 minutes. However, if you need to force starting it, you have to pull out the power plug for 10 seconds and connect it again to work).

11. When the oil press jams, please press the Start/Pause button and then press Reverse for 5 seconds. The ingredients will be pushed into reverse, unjamming the oil pressing machine. Press the Start/Pause button to operate it again. Please keep in mind that if this happens 3 times, it will enter protection mode and it will not work until stopped and powered again.

Please read carefully this user manual and all the safety precautions before using the product.

SAFETY INSTRUCTIONS

• When using electrical appliances, basic safety precautions should be observed, including the following:
• Make sure that your output voltage corresponds to the voltage stated on the rating label of the appliance.
• If the appliance orits power cord has been damaged, it must be repaired or replaced by the manufacturer, a service technician, or a similarly qualified person, to prevent hazards.
• Before cleaning the appliance, be sure that it has cooled completely and that it is unplugged from the outlet.
• To protect yourself from electric shock, do not immerse the power cord, plug, or appliance in water or other liquids.
• Misuse of this appliance may result in severe personal injury.
• Always unplug the unit prior to assembly, after use, before cleaning, and in the event of any malfunction.
• Always unplug the unit before opening the bean or collection container and before removing either from the housing.
• This appliance may be used by persons with reduced physical, sensory or mental capabilities or lack of experience or knowledge, provided that they are supervised or instructed in the safe use of the appliance and that they fully understand the potential hazards.
• Before each use, check the appliance, its power cord, and its attachments for any defects. If the appliance has been dropped or if excessive force has been used to pull the power cord or plug, then the appliance should not be used because even invisible damage may have adverse effects on the operational safety of the appliance.
• The appliance and its cord must never be placed near or on top of hot surfaces such as a radiator, ovens, gas burners, open flames, etc.
• When unplugging the unit, always grip the plug itself. Do not jerk or pull the power cord.
• Do not allow the cord to hang over the edge of the counter or table.
• This appliance may be used by children of at least 8 years of age, as long as they are supervised and have been given instructions about using the appliance safely and are fully aware of the dangers involved.
• Cleaning and maintenance should not be carried out by children unless they are at least 8 years of age and are supervised by an adult.
• Keep the appliance and its power cord out of reach of children under 8 years of age.
• When using electrical equipment, safety precautions must always be taken to prevent the risk of fire, electric shock and/or injury in the event of misuse.
• Make sure that the voltage rating on the typeplate corresponds to your main voltage of your installation. If this is not the case, contact the dealer and do not connect the unit
• Please keep this document at hand and give it to the future owner in case of transfer of your device
• Never leave the unit unattended while in operation.
• The device must not be used if it has been dropped, it obvious signs of damage are visible or if it has leaks.
• This appliance is intended for use in domestic and similar applications such as :
• kitchen areas in shops, offices and other working environments
• farmhouses
• in hotels, motels and other residential environments
• guest rooms.
• Please do not use the machine for other purposes outside of its original function.

NOTE:

Do not try to change parts or the power The machine is designed to process sunflower seeds, pumpkin seeds, flaxseed, sesame, rapeseed, peanuts, walnuts, etc. Do not try to process anything else but the seeds and nuts we advise you to! Consult the list of processable items in this user

GENERAL DESCRIPTION

TECHNICAL SPECIFICATIONS

• SWITCHING CONTROL: ON / OFF
• DIMENSIONS: 355 178 264 mm
• THERMAL CONTROL: Temperature probe + Thermal protection
• MOTOR POWER: 180 W
• HEATING MODE: Heating element and extrusion shaft
• HEATING POWER: 330 W
• OUTPUT POWER: 510 W
• VOLTAGE RATING: 220-240V~/50-60 HZ
• WEIGHT: 6,8 KG

ACCEPTED SEEDS

We advise you to dry/dehydrate your seeds before use.
WARNING : This oil press does not allow the extraction of olive oil.

HOW TO USE THE OIL PRESS MACHINE

1. Rotate to open the hopper lid.
2. Put the ingredients in the hopper.
   • Note: Please use clean and high oil content ingredients (dried). If they contain stones, sand, or metal, this could damage the inner parts. Ingredients larger than a peanut should be cut into smaller pieces before being inserted.

When the oil press jams, please press the Start/Pause button and the press Reverse for 5 seconds. The ingredients will be pushed into reverse, unjamming the oil pressing machine. Press the Start/Pause button to operate it again. Please keep in mind that if this happens 3 times, it will enter protection mode and it will not work until stopped and powered again.

CLEANING AND MAINTENANCE

1. We recommend that you leave the machine to cool down a bit, after it has been used, but still, the items have to be like warm, so this will ease your job, the residues will not stick to the metal parts.
2. Remove the protection cover.
3. Unscrew the extrusion shaft with the special spanner included in the box, in a counterclockwise direction and then take out the outer part.
4. Clean the extrusion shaft and its outer element with a soft towel or cloth. Corrosive detergent should not be used.
5. Clean the outer element with the brush and make sure there is no residue inside.
6. Fix the extrusion shaft and then the outer element when you assemble the machine.

TROUBLESHOOTING

“reverse” button for 5 seconds and the extrusion shaft will reverse back the ingredients. Then press “Start/Pause” button.

B: Turn off and pull out the plug. Disassemble the out element and extrusion shaft, clean the items as well as the hopper and its entrance. Assemble it back!

2| The motor stops rotating and doesn’t squeeze the oil| **** A: It is normal for the motor to take 30-45 seconds to preheat the extrusion shaft before it starts squeezing.

B: Check if the hopper lid or oil box are in the correct position.

3| The motor stops without any notice while the machine is working| A: If it has been working for more than 45 minutes, it is normal that it enters self-protection mode.

B: If more than a minute has passed from the last processed ingredient, it is normal the oil presing machine has stopped.

C: If the oil pressing machine has stopped 3 times, because being jammed, it will enter as well, in self protection mode.

---|---|---

TIPS & TRICKS

• To make high quality oil and avoid the machine getting stuck or parts damaging, please select good quality ingredients, with high oil content, without stones or sand otherwise it will damage parts or stuck the machine.
• Use ingredients with high oil content, avoid ingredients that are rotten, oxidized or have low oil content. Soybean is not a proper ingredient, please avoid it!
• Special tip for peanuts: we suggest you fry the peanuts before pressing them. Fry them at 80 centigrades but don’t over fry them because the beans could get burn.
• The oil extraction rate is very good if the ingredients are dry up to 90%. For better results, we reccomend you to dry the ingredients for about 1 hour under the sun or in a dehydrator at 60 centigrades.
• It is necessary to clean the extrusion shaft with a clean and soft cloth or towel after every use. Try not to use water, don`t use detergent!
• Depending on the type of ingredient you are using, it processes around 100-150 g of ingredients every 5 minutes.
• The efficiency of the squeezing process is between 30-75 %, depending on ingredients, for instance, out of 100 g of walnuts, you can squeeze about 75 ml of oil, out of 100 g of flaxseed you get around 45 ml of oil.
• Freshly squeezed oil is not clear, it has sediments, after a while, if it is not stirred, the sediment settles. Anyway, the oil is cold pressed, it does not oxidize, it is a natural source of proteins, vitamins and fatty acids.
• The residue can be used for preparing food or as a sauce material.

HOW MUCH OIL CAN YOU SQUEEZE OUT OF: (FOR REFERENCE ONLY)

Ingredients| Oil content| Oil extraction| factors that influence efficiency
---|---|---|---
Peanut| 40-52| 40-50| **** Type of ingredient Moisture Squeezing speed

Squeezing temperature

Sesame| 40-50| 45-55
Rape seed| 30-35| 30-40
Sunflower seed| 45-50| 50-65
Flax seed| 35-40| 30-34

MATCHING TABLE

not listed elsewhere

NOTE: walnuts, peanuts, macadamia and hazelnuts should be squashed into smaller pieces.

ATTENTION

1. We don’t recommend you to process soybeans as their oil content is lower than 10%.
2. Be careful when selecting the preset to be in accordance with the ingredient you are processing and if the ingredient is not listed, find the proper correspondant in the matching table.
3. Pick carefully your ingredients and remove any trace of dirt, iron residue, sand, stones, wood, or anything else that is not suitable for being squeezed.
4. If you haven`t used the oil pressing machine for a long time and decide to use it again, take into consideration that you first have to process a small quantity of ingredients just to clean the extrusion shaft, we would advise you not to drink the oil that comes out first.
5. Check if all the parts are well fitted, if not, fit them accordingly to instructions. Don`t operate the machine if the parts are not in place.
6. Don’t try to disassemble the extrusion shaft or the outer element immediately after processing, leave them to cool off, otherwise, you will burn your hands. The parts are hot immediately after processing.
7. We advise you to follow the operating guidelines provided. Do not operate the oil pressing machine for more than 45 minutes, however, if it enters protection mode, do not force restart, leave it for 30 minutes to cool down and then try to start it again.

FREQUENTLY ASKED QUESTIONS

Is the machine safe? Did it pass testing?

• Yes – it is safe, it is UL and CE certificated.

Which is the power rating?

• Motor power is rated at 180W, the heating element power is rated at 300 W. The motor runs as long as it processes, the heating element runs just when heating the extrusion shaft. The motor does not
  run all the time at full power.

How much material can be put in the hopper at one time?

• The hopper can hold 400-450g of ingredients, the extracted oil meets the daily needs of 3-5 people.

What is oil content and extracting rate?

• It depends a lot on the type of ingredient you are squeezing. Usually, seeds or nuts produce around 40-75 % of their weight as oil.

What is oil content and extracting rate of soybean or corn?

• Soybeans and corn are two ingredients with very low oil content. The oil content of soybeans is only 10-15%, so, they are very dry and hard, as corn is. We advise you not to try to use this kind of ingredients.

Why does the oil look turbid?

• Natural, cold pressed oil is not clear, it contains sediments, if you leave it for 2-3 hours to settle, it will become clear and you will have sediments on the bottom of the glass.
• Why is the outcome from some ingredients very low?
• Mainly because you are not using the proper ingredient or the proper preset. Check out if your ingredient is listed in our chart, if not, check for compatibility, otherwise, it means that it is not good for being squeezed.

How can I store the oil?

• The oil can be stored for at least one month in the refrigerator in a sealed glass bottle.

Can I eat the oil if it’s turbid?

• Yes, even if it is turbid, the oil is fresh, natural and edible.

Why is the residue moist sometimes?

• It has to do with the ingredients themselves. If the ingredients are not dry, the residue will not be as dry as powder. The moisture in the ingredients will come out as residue. If you fry or dry in the sun the ingredients that still have moisture you will obtain a very dry powder as residue. Another reason would be not using the proper preset for your ingredients.

The filter gets often blocked – what can I do about it?

• It has to do with the used ingredients, they are not of good quality, are too large or contain moisture. Choose other ingredients or clean them more often the filter;

Why is there still oil coming out of the oil press even if I have stopped it?

• There is still oil left inside even after the machine stops, so please keep the oil box in place for around 10 minutes after the machine stops.

When the machine stops there is still residue inside or in front of the extrusion shaft – what should I do?

• When the pressing operation is nearly finished there is no material inside to push the residues out so there will be some residues that will remain inside. Disassemble the extrusion shaft and the outer element and clean them.

How should I clean the bottom of the oil box and the surrounding area?

• Use a dry cloth, a clean towel, and/or a brush.

The machine is hot when operating – why is this?

• Do not worry, heating is absolutely normal. The machine can get as hot as 50 centigrade, anyway, it has overheating protection so when the temperature will exceed the safety level, the machine will stop and enter protection mode.

Why does the machine stop itself after not having anything in the hopper for 1 minute?

• It is a safety precaution, when not having anything to process, it will stop itself after 1 minute.

There are no ingredients in the hopper – why is the oil pressing machine still working?

• You can only see that there is nothing in the hoper, but there are still ingredients in the outer element so the machine will continue to work until it finishes processing all the ingredients.
• There is a smell coming out during the first operation of the machine

How should I proceed?

• Usually, home appliances that have plastic elements tend to smell a bit sometimes, because the fresh plastic heats up and produces odor. The smell will disappear after processing 3-4 times.

WARRANTY

• The warranty period for our products is 2 years unless otherwise stated, starting from the date of initial purchase or the date of delivery.
• If you have any problems or questions, you can easily access our help pages, troubleshooting tips, FAQs, and user manuals on our service site: https://sav.hkoenig.com.
• By typing the reference name of your device in the search bar, you can access all available online support, designed to best meet your needs.
• If you still cannot find an answer to your question or problem, then click on “Did the answer solve your problem?”. This will direct you to the Customer Support Request Form, which you can fill out to validate your request and get help.

WARRANTY CONDITIONS

• The warranty covers all failures occurring under normal use, in accordance with the usage and specifications in the user’s manual.
• This warranty does not apply to packaging or transportation problems during the shipment of the product by the owner. It also does not include normal wear and tear of the product, nor maintenance or replacement of consumable parts.

EXCLUSION OF WARRANTY

• Accessories and wearing parts (*).
• Normal maintenance of the device.
• All breakdowns resulting from improper use (shocks, failure to comply with power supply recommendations, poor conditions of use, etc.), insufficient maintenance or misuse of the device, as well as the use of unsuitable accessories.
• Damage of external origin: fire, water damage, electrical surge, etc.
• Any equipment that has been disassembled, even partially, by persons other than those authorized to do so (notably the user).
• The products whose serial numbers would be missing, deteriorated, or illegible would not allow identification.
• The products are subjected to leasing, demonstration, or exhibition.
• Some parts of your device, called worn parts or consumables, deteriorate with time and frequency of use of your device. This wear and tear are normal but can be accentuated by poor conditions of use or maintenance of your device. These parts are therefore not covered by the warranty.
• The accessories supplied with the device are also excluded from the warranty. They cannot be exchanged or refunded. However, some accessories can be purchased directly through our website: https://sav.hkoenig.com/.

ENVIRONMENT

CAUTION:

• Do not dispose of this product as it has with other household products. There is a separation of this waste product into communities, you will need to inform your local authorities about the places where you can return this product. In fact, electrical and electronic products contain hazardous substances that have harmful effects on the environment or human health and should be recycled. The symbol here indicates that electrical and electronic equipment should be chosen carefully, a wheeled waste container is marked with a cross.
• Adeva SAS / H.Koenig Europe – 8 rue Marc Seguin – 77290 Mitry Mory – France  www.hkoenig.com – sav@hkoenig.com – contact@hkoenig.com – Tél: +33 1 64 67 00 05

References

• H.Koenig : Le spécialiste du petit électroménager
• HKOENIG SAV: Pièces détachées ,accessoires, FAQ
• HKOENIG SAV: Pièces détachées ,accessoires, FAQ

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>