Kuryakyn GL1800 7513 LED Mirror Lights Instruction Manual
- June 13, 2024
- KURYAKYN
Table of Contents
Kuryakyn GL1800 7513 LED Mirror Lights Instruction Manual
ATTENTION!
THE LED MIRROR LIGHTS ARE MADE TO BE “PLUG AND PLAY” COMPATIBLE WITH KÜRYAKYN
LIGHT BARS. WHILE THE LED MIRROR LIGHTS ARE ALSO COMPATIBLE WITH ORIGINAL
LIGHTS, OR CAN BE USED ALONE, THEY WILL REQUIRE HARD WIRING TO THE BIKE’S
STOCK WIRING HARNESS UNLESS YOU ORDER TWO PLUG AND PLAY ADAPTERS, P/N 607312P,
SOLD SEPARATELY.
PARTS INCLUDED
2 LED Mirror Lights
1 Installation Instructions
Please read and understand entire instructions before starting installation.
THANK YOU FOR CHOOSING KijRYAKYN!
PLEASE NOTE
It is the installers’ responsibility to make sure all fasteners (including
pre-assembled) are tightened before operation of motorcycle. Küryakyn will not
warranty components that are lost due to improper installation. Periodic
maintenance may be required.
TOOLS SUGGESTED
Phillips screwdriver, Wire stripper, Soldering supplies, Electrical tape
PROCEDURE
STEP 1 See PIC.I. Insert your Phillips screwdriver into the hole on the
bottom of each mirror housing and remove the Phillips screw that holds the
mirror assembly in place. Loosen or remove the mirror assembly.
NOTE
If Küryakyn “Light Bars” are being installed with these mirror lights, the
mirror lights may simply be plugged into the connector that comes with the
Light wiring. Proceed to STEP 4.
If these lights are used with the original Lights without the plug in
connection or used by themselves, cut the plug off, and proceed with STEP 2
through STEP 4.
STEP 2 See PIC.2. Cut back some of the vinyl enclosure that surrounds the
three turn signal wires in each mirror housing.
-cont.-
steP 3 See PIC.3. DO nOT fully cut any of the bikes OEM wiring.
LEFT SIDE: Skin back a little of the insulation on the green and orange wires.
Splice the black wire from the LED harness to the green wire on the bike’s
stock harness. Splice the black and white wire from the LED harness to the
orange wire on the bike’s stock harness. Carefully solder and insulate your
splices.
RIGHT SIDE: Skin back a little of the insulation on the green and light blue
wires. Splice the black wire from the LED harness to the green wire on the
bike’s wiring harness. Splice the black and white wire from the LED harness to
the light blue wire on the bike’s wiring harness. Carefully solder and
insulate your splices.
steP 4 See PIC.4. Trial fit the light pod on the mirror to determine the
points where the adhesive pads will rest on the mirror back. Thoroughly clean
this area with windex, alcohol, etc. and let dry. Remove the adhesive backing
and permanently affix the light pods to the mirror as shown.Test the light by
activating the turn signal. Re-install the mirror in the housing.
Ride On!
CUSTOMER SERVICE
877.370.3604 (toll free)
INSTALLATION QUESTIONS
techsupport@kuryakyn.comor call 715.247.2983
LIMITED WARRANTY
Küryakyn warrants that any Küryakyn products sold hereunder, shall be free of
defects in materials and workmanship for a period of one (1) year from the
date of purchase by the consumer excepting the following provisions:
Küryakyn shall have no obligation in the event the customer is unable to provide a receipt showing the date the customer purchased the product(s).
The product must be properly installed, maintained and operated under normal conditions.
Küryakyn makes no warranty, expressed or implied, with respect to any gold plated products.
Küryakyn shall not be liable for any consequential and incidental damages, including labor and paint, resulting from failure of a Küryakyn product, failure to deliver, delay in delivery, delivery in nonconforming condition, or for any breech of contract or duty between Küryakyn and a customer.
Küryakyn products are often intended for use in specific applications. Küryakyn makes no warranty if a Küryakyn product is used in applications other than intended.
Küryakyn electrical products are warranted for one (1) year from the date of purchase by the consumer. Components of Küryakyn products containing L.E.D.s will be warranted for defects in materials and workmanship for 3 years from the date of purchase.
Küryakyn makes no warranty of any kind in regard to other manufacturer’s products distributed by Küryakyn. Küryakyn will pass on all warranties made by the manufacturer and where possible, will expedite the claim on behalf of the customer, but ultimately, responsibility for disposition of the warranty claim lies with the manufacturer.
ABOUT OUR CATALOG
You’ll find all our innovations for H-D, GL and Metric Cruisers in our annual
catalogs. Order online today–select the ”CATALOGS” icon. Each Küryakyn®
product comes with a Proof-of-Purchase good for a complimentary catalog.
Details in packaging. Be sure to ask your local dealer about other Küryakyn
products, the motorcycle parts and accessories designed for riders by riders.
©2005 Küryakyn USA® All Rights reserved.
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>