Kuryakyn 2713 Weather Resistant Motorcycle Speakers User Guide
- June 4, 2024
- KURYAKYN
Table of Contents
Kuryakyn 2713 Weather Resistant Motorcycle Speakers
Specifications
- Product Dimensions :15 x 10.5 x 5.2 inches
- Item Weight:4.5 pounds
- Exterior:Satin Black
- Speaker Type :Soundbar
- Connectivity Technology: Bluetooth
- Compatible Devices: Android & IOS
- Brand: Kuryakyn
Introduction
Thank you for purchasing this Kuryakyn RoadThunder Speaker Pods and Bluetooth
Audio Controller by MTX that are designed to work with most Bluetooth-enabled
devices including iPhone® and Android® smartphones and tablets. This easy-to-
install and use, the all-in-one unit is capable of transforming your
Bluetooth-enabled mobile device into the center of your vehicle’s audio
system. Designed to mount on any motorcycle handlebars with a 7/8” or 1”
diameter. Congratulations and enjoy the ultimate audio experience!
The compact size and maximum sound quality of the Kuryakyn 2713 MTX Road
Thunder Speaker Pods with Bluetooth Audio Controller enable you to bring the
noise and wirelessly connect any Bluetooth-enabled device. Gain 100W of peak
power with only 5 amps of current draw. High-impact ABS casings are used to
create the speaker pods, which have a satin-black appearance. The pods and
controller also meet IP66 classification standards for weather resistance.
Protect yourself and others from possible injury and property damage or loss.
Pay close attention to all instructions, warnings, cautions, and notices
regarding the installation, use, and care of this product.
Warning
THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED
HEREIN CAN RESULT IN POTENTIAL DEATH OR SERIOUS INJURY
Caution
THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED
HEREIN CAN RESULT IN POTENTIAL DEATH OR SERIOUS INJURY.
Notice
THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED
HEREIN MAY NEGATIVELY AFFECT PRODUCT PERFORMANCE AND FUNCTIONALITY OR DAMAGE
THE PRODUCT ITSELF OR THE PRODUCT TO WHICH IT IS BEING ATTACHED.
ENSURE THAT THE FOLLOWING PARTS HAVE BEEN INCLUDED IN THE KIT YOU WILL ALSO
NEED
Metric Hex, Allen wrenches, Pliers
INSTALLATION INSTRUCTIONS
Notice
THESE INSTALLATION INSTRUCTIONS CONTAIN IMPORTANT INFORMATION. ENSURE THE END
USER RECEIVES THIS COPY AND IS AWARE OF ITS IMPORTANCE FOR FUTURE USE.
WHEN CONNECTING POWER AND GROUND WIRES ENSURE THAT THE RED POWER WIRE IS FUSED
AT THE POINT WHERE IT IS CONNECTED TO THE VEHICLE’S BATTERY. FAILURE TO DO SO
CAN RESULT IN DAMAGE TO THE VEHICLE IF A SHORT CIRCUIT DEVELOPS BETWEEN THE
VEHICLE CONNECTION POINT AND THE PRODUCT.
Warning
THE END USER’S SAFETY DEPENDS UPON PROPER INSTALLATION OF THIS PRODUCT. IF A
STEP IN THESE INSTRUCTIONS IS NOT WITHIN YOUR CAPABILITIES OR YOU DO NOT HAVE
THE CORRECT TOOLS, HAVE YOUR DEALER PERFORM THE PROCEDURE. IMPROPER
INSTALLATION OF THIS PRODUCT COULD RESULT IN DEATH OR SERIOUS INJURY.
ACCIDENTAL VEHICLE START-UP COULD CAUSE DEATH OR SERIOUS INJURY, REMOVE THE
MAIN FUSE BEFORE PROCEEDING.
FEATURES
BLUETOOTH CONTROLLER SPECS
- Compatible with most Bluetooth devices, including Android and iPhone
- Easy to install with hassle-free auto pairing and five front panel touch controls
- Durable, weather-proof design
- Includes two adjustable bar mount brackets: 7/8” through 1” and 1-1/8” through 1-1/4”
- Includes power, ground, and output connections 3” SPEAKER PODS SPECS
- High-impact ABS enclosures in chrome or satin black finish
- Low current draw: 5 amps
- Overall height when mounted is 4.8”
- Includes 3.5 mm input and output connectors
- 1-1/4” handlebar clamp mount available separately, P/N 1468 Chrome, 2792 Satin Black
- 100W Peak Music Power
INSTALLATION
The RoadThunder Speaker Pods & Bluetooth Audio Controller can be used with any
12-volt battery and can be mounted to a variety of bars using the included
hardware. Mount the speakers where they have sufficient clearance, and
position the speakers so the speakers are directly at the rider.
MOUNT BRACKETS TO HANDLEBAR FIRST, THEN INSTALL SPEAKER PODS
-
STEP 1 Determine the diameter of the handlebar and use either the 7/8” Adaptor with 1” Bracket or just the 1” Bracket
Note
If you have a 1-1/4” diameter handlebar you can purchase that bracket separately on the Kuryakyn website. -
STEP 2
Install brackets on handlebars where Sound Bars do not obstruct the riders view. Use hardware that is included with the brackets. -
STEP 3
Once brackets are installed, add the Speaker Pods with the hardware provided: A) Add the 3” Amp Speaker POD to the left side of the rider’s perspective & 3” Speaker POD to the right side of the rider Use one of the M8 1-1/4” x 45 Cap Screw provided on each bracket along with two M8 internal Tooth Lock Washers add to top and bottom surface of the bracket, do the same on another bracket. -
STEP 4
Adjust the speaker pods so the speakers are directed at the rider’s head. To adjust and align the logo on the Speaker Pods mesh screen there is a very small pin size hole located at the bottom of the front ring. Use a small pin or paper clip, press in, and turn the ring. Rotate trim counterclockwise to remove trim ring. Once the ring has been removed, adjust the mesh screen accordingly, then reinstall. Make sure all screws are securely fastened and tightened. -
STEP 5
Connect Speaker Pods to the Wire Harness.
Route all harness wires through the bike’s frame to the battery and proceed to the next steps in power connection.
Notice
SECURE THE WIRING AWAY FROM MOVING PARTS, PINCH POINTS, OR EXTREME HEAT.
KURYAKYN WILL NOT PROVIDE WARRANTY COVERAGE ON ANY ELECTRICAL COMPONENT THAT
FAILS DUE TO PINCHED, CRIMPED, BROKEN ABRADED, MELTED, OR FRAYED WIRES.
POWER CONNECTION
SPEAKER PODS WIRE HARNESS CONNECTION (RECOMMENDED INSTALLATION)
STEP 1
Connect the Red wire (with the in-line fuse) power wire from the wire harness
to the positive terminal on the battery. The Black wire is a ground wire and
needs to be attached to the negative terminal on the battery.
Note
Keep the included fuse off the fuse holder until all wiring connections have
been made and secured.
BLUETOOTH AUDIO CONTROLLER POWER CONNECTION
-
STEP 1
Connect the Red wire power wire from the wire harness to the positive terminal on the battery. The Black wire is a ground wire and needs to be attached to the negative terminal on the battery. -
STEP 2
Extend and connect the Blue 12V output wire from the Bluetooth Audio Controller to the Orange wire on the POD wire harness. This will allow the Bluetooth Audio Controller to turn on and off the Speaker Pods. In this installation you will need to tap into the side of the blue wire from the Bluetooth Audio Controller with the T-Tap Quick Connect Female provided and then connect the orange wire terminal from the Speaker Pods to this T-Tap connector.
Note
The blue wire on the Bluetooth Audio Controller should not be connected to any positive or negative 12V source. This wire will energize when the unit is turned on, and will turn off when the unit is turned off. It should only be connected to a 12V turn on circuit. Do not connect it to the main power of any device.
BLUETOOTH AUDIO CONTROLLER POWER CONNECTION (OPTIONAL INSTALLATION)
-
STEP 1
Use the included T-Tap Quick Connect Female connector and install directly onto the ACC/Key ignition wire on the motorcycle using a pair of pliers. Then once the T-Tap female connector is installed, connect the Orange wire with red male connector onto this T-Tap female connector.
Notice
IF THE ORANGE WIRE ON THE SPEAKER PODS IS CONNECTED TO ACC/KEY OF THE BIKE, THE BLUE WIRE FROM THE BLUETOOTH AUDIO CONTROLLER SHOULD NOT BE CONNECTED TO THE ORANGE WIRE. -
STEP 2
The blue wire on the Bluetooth Audio Controller can be left disconnected. This will allow the ACC/Key ignition to turn on the Speaker Pods.
BLUETOOTH AUDIO CONTROLLER POWER CONTROL (OPTIONAL INSTALLATION)
-
STEP 1
Connect the RED wire directly to the ACC/Key ignition. This will allow the Bluetooth unit to be turned on and off with the Bike electrical system. In this installation you will need a Quick Connect Male connector (same as what is on the existing POD’s orange wire) and merge both Red (Bluetooth Audio Controller) and Orange (Speaker Pods) wires together. -
STEP 2
Connect the Black wire directly to the negative terminal on the battery.
AUDIO CONNECTION WITH BLUETOOTH AUDIO CONTROLLER
STEP 1
Use the included 3.5mm male connector on the Speaker Pods and connect directly
to the 3.5mm female connector on the Bluetooth Audio Controller. Route and
secure the wiring away from any moving parts, pinch points or extreme heat
DIRECT CONNECTION FROM AUDIO SOURCE
STEP 1
Use the included 3.5mm male connector on the Speaker Pods and connect directly
to an audio source.
Note
Please note with this type of connection, the audio source will control the
volume of the pods.
BLUETOOTH AUDIO CONTROLLER AND SPEAKER PODS AUDIO OPERATION
-
STEP 1
Play/Pause – The Play/Pause button gives you the ability to play or to pause the current track with a single press. Holding the Play/Power button for 2 seconds will turn the unit On if currently Off or Off if currently powered On. The unit will beep to indicate when power is turned Off.
Note- The unit will stay on indefinitely as long as a Bluetooth device is actively paired to the Bluetooth Audio Controller.
- The unit will turn Off after 5 minutes when there is no active Bluetooth device connection.
- The Play/Pause button will illuminate when the unit is powered On.
- The Play/Pause button will blink when the music track is paused.
-
STEP 2
Track Forward and TrackBack – The unit will switch audio tracks being played by pressing the track forward and track back buttons. Pressing and holding these buttons for 2 seconds will fast forward or rewind the audio track that is being played. -
STEP 3
Volume Up and Volume Down – These buttons will turn up or turn down the output connected to the Speaker Pods controlling the system volume. When the unit has reached the minimum or maximum output level, the unit will beep to indicate that no further adjustment is possible.
BLUETOOTH AUTO-PAIR MODE
-
STEP 1
Turn the unit On. -
STEP 2
Search for MTX REMOTE from your device’s Bluetooth menu -
STEP 3
Select Pair
AUDIO OUTPUT ON SPEAKER PODS
The 3.5mm audio output on the Speaker Pods can be connected to a second
Speaker Pods system or any other audio device.
If connected to a second Speaker Pods system, the second set of powered pods
will be controlled by the volume setting of the connected Bluetooth Audio
Controller or audio source. Both sets of Speaker Pods will play at the same
volume.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
this is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, you are encouraged to try to correct the interference by one or more of
the following measures
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a different circuit than the one to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
LIMITED WARRANTY
Kuryakyn warrants that any Kuryakyn products sold hereunder, shall be free of defects in materials & workmanship for a period of one (1) year from the date of purchase by the consumer excepting the following provisions
- Kuryakyn shall have no obligation in the event the customer is unable to provide a receipt showing the date the customer purchased the product(s).
- The product must be properly installed, maintained & operated under normal conditions.
- Kuryakyn shall not be liable for any consequential & incidental damages, including labor & paint, resulting from the failure of a Kuryakyn product, failure to deliver, delay in delivery, delivery in nonconforming condition, or for any breach of contract or duty between Kuryakyn & a customer.
- Kuryakyn products are often intended for use in specific applications. Kuryakyn makes no warranty if a Kuryakyn product is used in applications other than intended.
- Kuryakyn electrical products are warranted for one (1) year from the date of purchase by the consumer. L.E.D.’s contained in components of Kuryakyn products will be warranted for defects in materials & workmanship for 3 years from the date of purchase whereas all other components shall be warranted for one (1) year.
- All warranty claims must be directed to the place of purchase. Merchandise sold through internet auction sites or any other unauthorized reseller shall not carry a Kuryakyn warranty. If unsure, please contact the place of purchase to verify they are an authorized Kuryakyn reseller.
RETURN POLICY
Merchandise determined to be defective may be returned up to one year from the
date of purchase. Returns must be processed through the original seller.
Returned merchandise for any other reason other than warranty claims must be
in like new condition & subject to a 20% restocking fee. All returns are
subject to inspection for determination of full or partial credit. Any
returned part that shows evidence of being used or installed contrary to
manufacturer’s instructions, &/or subjected to improper handling, packaging or
return shipping by the customer, will not be eligible for exchange, refund or
warranty consideration. All returned electrical items will be inspected &
tested. If an electrical item is deemed functional, no credit will be issued &
item will be returned. All sales are final on discontinued or closeout
merchandise.
©2015 KURYAKYN HOLDINGS, LLC ALL RIGHTS RESERVED
URYAKYN, KURYAKYN K logo, and the marks appearing on this instruction sheet
are registered and common law trademarks of Kuryakyn Holdings except for noted
third-party trademarks. A full listing of trademarks and trademark
registrations owned by Kuryakyn Holdings can be found at www.kuryakyn.com
/legal-notice.
Emissions Notice
The California Air Resources Board (CARB) does not permit the use of
aftermarket emission-related parts(s) that alter the performance of OEM
emission-related devices unless CARB has issued an Executive Order, other than
on racing vehicles on closed courses. Check your local laws and manufacturer’s
information
Listed Manufacturers and product model names are for reference only. All
product and company names are trademarks or registered trademarks of their
respective holders. Use of them does not imply any affiliation with or
endorsement by them. All specifications are subject to change without notice.
For additional information on third-party products and company names, please
consult our Web page at www.kuryakyn.com/legal-
notice
Frequently Asked Questions
Are these speakers self-powered, or do you need to add an amp to them?
You will not add an amp as they are self-powered.
You will not add an amp as they are self-powered.
You are able to add the 6 1/2″ speakers but they will not perform properly due to the pods only having a 150-watt amp. Also adding the 6 1/2″ will decrease the performance of the pods themselves.
Can these connect to the 2719 road thunder sound bar?
Yes, they can but when I did it, it still wasn’t loud enough for my bike’s loud pipes at higher speeds or higher RPMs and highway speeds forget it. I even set up two soundbars (both 300watt) and still wasn’t loud enough. So my point is if you’re adding them to try and get a louder sound system because just the sound bar isn’t loud enough for your setup, then save yourself the money and time and don’t buy them.
Can a motorcycle have speakers?****
Motorcycle speakers are a wonderful method to make your bike stand out because buyers frequently search for benefits and features that set one motorcycle apart from the competition. Installing motorbike speakers is a long-term investment that will pay you if you ever decide to sell, in addition to the short-term, immediate benefits they provide.
Are amplifiers required for motorcycle speakers?****
The majority of decks and motorcycle speaker systems come with built-in amplifiers, which improve the sound even more than it was before. You need a specialised amplifier for the job because these default amplifiers typically lack the power to send high-quality sound signals to premium speakers.
Can you ride a motorcycle and listen to music?****
Although many people hold this belief, it is untrue. 9.4% of respondents also believed that singing along to music while riding a motorcycle was against the law. It is not against the law for motorcycle riders to sing along or listen to music.
How wide it the clamp bar? I know it fits a 1″ tube but I need the mount width.
The clamp is 3/4″ wide.
Are all the dimensions in inches? A 15-inch speaker sounds huge for a handlebar?
The #2713 is Diameter – 3.07” / 78mm & Overall height when mounted – 4.8” / 122mm. The 15 is a misprint apparently.
How many watts are recommended for motorcycle speakers?****
WATTAGE OF MOTORCYCLE SPEAKERS
Aim for closer to 600 watts if you commute by bike on the highway. When turned
up to maximum volume, your music will sound better the higher the wattage.
Can a motorcycle have a radio?****
On a motorcycle, installing an aftermarket radio is a little trickier than in a car. A radio might already be installed on a larger touring motorbike. On these kinds of motorcycles, adding an aftermarket radio is a simple exchange.
VIDEO
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>